Registers

The abbreviations given in Column Access are explained in Section Access Types for Registers .

Base Address:

  • CAN0_REG : 0x41005000

  • CAN1_REG : 0x41006000

Name

Address offset

Access

Description

REG_CAN_CTL

000h

R/W

Controls the fundamental operations and modes of the CAN bus

REG_CAN_STS

004h

R

Indicates the overall operational state of the bus

REG_CAN_FIFO_STS

008h

R

Monitors the status of the RX FIFO

REG_CAN_BIT_TIMING

00Ch

R/W

Configures the standard CAN 2.0 bit timing parameters (BRP, SJW, TSEG1, TSEG2)

REG_CAN_INT_EN

018h

R/W

A global switch to enable or mask various CAN system interrupts

REG_CAN_MB_RXINT_EN

01Ch

R/W

Enables or disables receive (RX) interrupts individually for each of the 16 message buffers.

REG_CAN_MB_TXINT_EN

020h

R/W

Enables or disables transmit (TX) interrupts individually for each of the 16 message buffers.

REG_CAN_INT_FLAG

024h

R/W

Stores the status flags that indicate which specific event (TX, RX, error, etc.) triggered an interrupt.

REG_CAN_ERR_STATUS

028h

R/W

Provides detailed diagnostics on the type of bus error that occurred

REG_CAN_ERR_CNT_CTL

02Ch

R/W

Sets the threshold for error warnings and provides a mechanism to clear the internal transmit/receive error counters.

REG_CAN_ERR_CNT_STS

030h

R

Displays the current numeric values of the Transmit Error Count (TEC) and Receive Error Count (REC), as well as node states (Warning, Passive, Bus-off)

REG_CAN_TX_ERROR_FLAG

034h

R/W

Flags which specific message buffer encountered an error during its transmission attempt.

REG_CAN_TX_DONE

038h

R/W

Flags which specific message buffer has successfully completed its transmission.

REG_CAN_RX_DONE

03Ch

R/W

Flags which specific message buffer has successfully received a new message.

REG_CAN_TIME_STAMP

040h

R/W

Manages the internal counter used to apply timestamps to received/transmitted messages, including its prescaler.

REG_CAN_MB_TRIGGER

044h

R/W

Sets up a timer-based trigger mechanism to schedule message transmissions within a specific time window.

REG_CAN_RXDMA_CFG

048h

R/W

Configures how the RX Direct Memory Access (DMA) operates

REG_CAN_RX_DMA_DATA

04Ch

R

Acts as the data port from which the DMA controller reads received message payloads.

REG_CAN_SLEEP_MODE

050h

R/W

Manages low-power sleep states, and configures the digital filter for the wakeup pin.

REG_CAN_TEST

054h

R/W

Enables special diagnostic modes, such as silent mode or internal/external loopback testing

REG_CAN_MB0_STS

100h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB1_STS

104h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB2_STS

108h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB3_STS

10Ch

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB4_STS

110h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB5_STS

114h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB6_STS

118h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB7_STS

11Ch

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB8_STS

120h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB9_STS

124h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB10_STS

128h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB11_STS

12Ch

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB12_STS

130h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB13_STS

134h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB14_STS

138h

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB15_STS

13Ch

R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

REG_CAN_MB0_CTRL

200h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB1_CTRL

204h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB2_CTRL

208h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB3_CTRL

20Ch

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB4_CTRL

210h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB5_CTRL

214h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB6_CTRL

218h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB7_CTRL

21Ch

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB8_CTRL

220h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB9_CTRL

224h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB10_CTRL

228h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB11_CTRL

22Ch

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB12_CTRL

230h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB13_CTRL

234h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB14_CTRL

238h

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB15_CTRL

23Ch

R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

REG_CAN_MB_BA_END

2F0h

R/W

Defines the ending boundary address in RAM allocated for message buffers.

REG_CAN_RAM_DATA_15

300h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_14

304h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_13

308h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_12

30Ch

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_11

310h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_10

314h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_9

318h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_8

31Ch

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_7

320h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_6

324h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_5

328h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_4

32Ch

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_3

330h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_2

334h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_1

338h

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_DATA_0

33Ch

R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the RAM.

REG_CAN_RAM_ARB

340h

R/W

Configures the message identifier (ID), format (IDE), and frame type (RTR) for a message buffer being written to or read from RAM.

REG_CAN_RAM_MASK

344h

R/W

Configures the acceptance filter masks, defining which bits of an incoming message ID must match to be accepted into the buffer.

REG_CAN_RAM_CS

348h

R/W

Configures control and status attributes of the message, such as Data Length Code (DLC) and direction (TX/RX).

REG_CAN_RAM_CMD

34Ch

R/W

Executes the command to transfer data between the CAN_RAM_* registers and the actual internal SRAM for a specified message buffer.

REG_CAN_DBG_PORT

3F8h

R/W

Selects and enables internal hardware signals to be routed to debug pins for hardware troubleshooting.

REG_CAN_DUMMY

3FCh

R/W

A reserved placeholder register used for hardware alignment or future expansion.

REG_CAN_CTL

  • Name: CAN bus control register

  • Size: 32

  • Address offset: 000h

  • Read/write access: R/W

Controls the fundamental operations and modes of the CAN bus

31:8 RSVD 7 CAN_RXDMA_EN 6 RSVD 5 RX_FIFO_EN 4 TEST_MODE_EN 3 AUTO_RE_TX_EN 2 CAN_TRI_SAMPLE 1 BUS_ON_REQ 0 CAN_EN

Bit

Symbol

Access

INI

Description

31:8

RSVD

R

-

Reserved

7

CAN_RXDMA_EN

R/W

0x0

Rx dma enable

6

RSVD

R

-

Reserved

5

RX_FIFO_EN

R/W

0x0

Rx fifo function enable

4

TEST_MODE_EN

R/W

0x0

Test mode enable, for lbk or silent mode use

3

AUTO_RE_TX_EN

R/W

0x0

Auto re-transmission enabled

2

CAN_TRI_SAMPLE

R/W

0x0

Triple sample mode

1

BUS_ON_REQ

R/W

0x0

Request to bus_on

0

CAN_EN

R/W

0x0

Can enable

REG_CAN_STS

  • Name: CAN bus status

  • Size: 32

  • Address offset: 004h

  • Read/write access: R

Indicates the overall operational state of the bus

31:1 RSVD 0 BUS_ON_STATE

Bit

Symbol

Access

INI

Description

31:1

RSVD

R

-

Reserved

0

BUS_ON_STATE

R

0x0

Bus state

  • 1 means the can module is already bus on

  • 0 means the can module is busoff

REG_CAN_FIFO_STS

  • Name: CAN bus FIFO status

  • Size: 32

  • Address offset: 008h

  • Read/write access: R

Monitors the status of the RX FIFO

31:7 RSVD 6:4 FIFO_MSG_LVL 3 RSVD 2 FIFO_MSG_OVERFLOW 1 FIFO_MSG_EMPTY 0 FIFO_MSG_FULL

Bit

Symbol

Access

INI

Description

31:7

RSVD

R

-

Reserved

6:4

FIFO_MSG_LVL

R

0x0

Rx fifo message level

3

RSVD

R

-

Reserved

2

FIFO_MSG_OVERFLOW

R

0x0

Rx fifo overflow

1

FIFO_MSG_EMPTY

R

0x1

Rx fifo empty

0

FIFO_MSG_FULL

R

0x0

Rx fifo full

REG_CAN_BIT_TIMING

  • Name: CAN2.0 bit timing

  • Size: 32

  • Address offset: 00Ch

  • Read/write access: R/W

Configures the standard CAN 2.0 bit timing parameters (BRP, SJW, TSEG1, TSEG2)

31:24 CAN_BRP 23:19 RSVD 18:16 CAN_SJW 15:8 CAN_TSEG2 7:0 CAN_TSEG1

Bit

Symbol

Access

INI

Description

31:24

CAN_BRP

R/W

0x0

CAN bit timing perscaler = <$bit:can_brp>+1

23:19

RSVD

R

-

Reserved

18:16

CAN_SJW

R/W

0x0

SJW length = <$bit:can_sjw>

15:8

CAN_TSEG2

R/W

0x0

TSEG2 length = <$bit:can_tseg2+1>

7:0

CAN_TSEG1

R/W

0x0

TSEG1 length = <$bit:can_tseg1+1>

REG_CAN_INT_EN

  • Name: CAN interrupt control

  • Size: 32

  • Address offset: 018h

  • Read/write access: R/W

A global switch to enable or mask various CAN system interrupts

31:22 RSVD 21 RAM_MOVE_DONE_INT_MASK 20 BUSOFF_INT_MASK 19 WAKEUP_INT_MASK 18 ERROR_INT_MASK 17 RX_INT_MASK 16 TX_INT_MASK 15:6 RSVD 5 RAM_MOVE_DONE_INT_EN 4 BUSOFF_INT_EN 3 WAKEUP_INT_EN 2 ERROR_INT_EN 1 RX_INT_EN 0 TX_INT_EN

Bit

Symbol

Access

INI

Description

31:22

RSVD

R

-

Reserved

21

RAM_MOVE_DONE_INT_MASK

R/W

0x0

Ram move done interrupt mask

  • 1: mask

  • 0: unmask

20

BUSOFF_INT_MASK

R/W

0x0

Wakeup interrupt mask

  • 1: mask

  • 0: unmask

19

WAKEUP_INT_MASK

R/W

0x0

Wakeup interrupt mask

  • 1: mask

  • 0: unmask

18

ERROR_INT_MASK

R/W

0x0

Error interrupt mask

  • 1: mask

  • 0: unmask

17

RX_INT_MASK

R/W

0x0

Rx interrupt mask

  • 1: mask

  • 0: unmask

16

TX_INT_MASK

R/W

0x0

Tx interrupt mask

  • 1: mask

  • 0: unmask

15:6

RSVD

R

-

Reserved

5

RAM_MOVE_DONE_INT_EN

R/W

0x0

Ram move done interrupt enable

4

BUSOFF_INT_EN

R/W

0x0

Wakeup interrupt enbale

3

WAKEUP_INT_EN

R/W

0x0

Wakeup interrupt enbale

2

ERROR_INT_EN

R/W

0x0

Error interrupt enable

1

RX_INT_EN

R/W

0x0

Rx interrupt enable

0

TX_INT_EN

R/W

0x0

Tx interrupt enable

REG_CAN_MB_RXINT_EN

  • Name: CAN rx interrupt for message buffers

  • Size: 32

  • Address offset: 01Ch

  • Read/write access: R/W

Enables or disables receive (RX) interrupts individually for each of the 16 message buffers.

31:16 RSVD 15:0 CAN_MB_RXINT_EN

Bit

Symbol

Access

INI

Description

31:16

RSVD

R

-

Reserved

15:0

CAN_MB_RXINT_EN

R/W

0x0

Rx interrupt enable for each message buffer

REG_CAN_MB_TXINT_EN

  • Name: CAN tx interrupt for message buffers

  • Size: 32

  • Address offset: 020h

  • Read/write access: R/W

Enables or disables transmit (TX) interrupts individually for each of the 16 message buffers.

31:16 RSVD 15:0 CAN_MB_TXINT_EN

Bit

Symbol

Access

INI

Description

31:16

RSVD

R

-

Reserved

15:0

CAN_MB_TXINT_EN

R/W

0x0

Tx interrupt enable for each message buffer

REG_CAN_INT_FLAG

  • Name: CAN interrupt flags

  • Size: 32

  • Address offset: 024h

  • Read/write access: R/W

Stores the status flags that indicate which specific event (TX, RX, error, etc.) triggered an

interrupt.

31:6 RSVD 5 RAM_MOVE_DONE_INT_FLAG 4 BUSOFF_INT_FLAG 3 WAKEUP_INT_FLAG 2 ERROR_INT_FLAG 1 RX_INT_FLAG 0 TX_INT_FLAG

Bit

Symbol

Access

INI

Description

31:6

RSVD

R

-

Reserved

5

RAM_MOVE_DONE_INT_FLAG

R/W

0x0

Data move from register to CAN IP internal RAM finished interupt, move from RAM to register done will NOT generate interrupt, write one to clear

4

BUSOFF_INT_FLAG

R/W

0x0

Busoff interrupt flag, write one to clear

3

WAKEUP_INT_FLAG

R/W

0x0

Wakeup interrupt flag, write one to clear

2

ERROR_INT_FLAG

R/W

0x0

Error interrupt flag, write to clear

1

RX_INT_FLAG

R/W

0x0

Rx interrupt flag, write to clear

0

TX_INT_FLAG

R/W

0x0

Tx interrupt flag, write to clear

REG_CAN_ERR_STATUS

  • Name: CAN error status

  • Size: 32

  • Address offset: 028h

  • Read/write access: R/W

Provides detailed diagnostics on the type of bus error that occurred

31:10 RSVD 9 CAN_ERROR_RX 8 CAN_ERROR_TX 7:6 RSVD 5 CAN_ERROR_ACK 4 CAN_ERROR_STUFF 3 CAN_ERROR_CRC 2 CAN_ERROR_FORM 1 CAN_ERROR_BIT1 0 CAN_ERROR_BIT0

Bit

Symbol

Access

INI

Description

31:10

RSVD

R

-

Reserved

9

CAN_ERROR_RX

R/W

0x0

Can rx error flag

8

CAN_ERROR_TX

R/W

0x0

Can tx error flag

7:6

RSVD

R

-

Reserved

5

CAN_ERROR_ACK

R/W

0x0

Latest error is ack error

4

CAN_ERROR_STUFF

R/W

0x0

Latest error is stuff error

3

CAN_ERROR_CRC

R/W

0x0

Latest error is ctc error

2

CAN_ERROR_FORM

R/W

0x0

Latest error is form error

1

CAN_ERROR_BIT1

R/W

0x0

Latest error is bit1 error, tx=1 but rx=0

0

CAN_ERROR_BIT0

R/W

0x0

Latest error is bit0 error, tx=0 but rx=1

REG_CAN_ERR_CNT_CTL

  • Name: CAN bus error counter control

  • Size: 32

  • Address offset: 02Ch

  • Read/write access: R/W

Sets the threshold for error warnings and provides a mechanism to clear the internal

transmit/receive error counters.

31:17 RSVD 16:8 CAN_ERROR_WARN_TH 7:2 RSVD 1 RX_ERR_CNT_CLR 0 TX_ERR_CNT_CLR

Bit

Symbol

Access

INI

Description

31:17

RSVD

R

-

Reserved

16:8

CAN_ERROR_WARN_TH

R/W

0x60

Error counter warning threshold, programable, default 96. NOTES: 0~127 is availaible to both TEC and REC, 128~255 is only available to TEC

7:2

RSVD

R

-

Reserved

1

RX_ERR_CNT_CLR

R/W

0x0

Write 1 to clear can_rec

0

TX_ERR_CNT_CLR

R/W

0x0

Write 1 to clear can_tec

REG_CAN_ERR_CNT_STS

  • Name: CAN bus error counter status

  • Size: 32

  • Address offset: 030h

  • Read/write access: R

Displays the current numeric values of the Transmit Error Count (TEC) and Receive Error Count (REC),

as well as node states (Warning, Passive, Bus-off)

31 RSVD 30 CAN_ERROR_WARNING 29 CAN_ERROR_BUSOFF 28 CAN_ERROR_PASSIVE 27:25 RSVD 24:16 CAN_REC 15:9 RSVD 8:0 CAN_TEC

Bit

Symbol

Access

INI

Description

31

RSVD

R

-

Reserved

30

CAN_ERROR_WARNING

R

0x0

Error counter arrive at warning threshold

29

CAN_ERROR_BUSOFF

R

0x0

Error counter arrive at bus off level

28

CAN_ERROR_PASSIVE

R

0x0

Error counter arrive at error passive level

27:25

RSVD

R

-

Reserved

24:16

CAN_REC

R

0x0

Receive error count

15:9

RSVD

R

-

Reserved

8:0

CAN_TEC

R

0x0

Transmit error count

REG_CAN_TX_ERROR_FLAG

  • Name: CAN tx error flag for each message buffe

  • Size: 32

  • Address offset: 034h

  • Read/write access: R/W

Flags which specific message buffer encountered an error during its transmission attempt.

31:16 RSVD 15:0 CAN_TX_ERROR_FLAG

Bit

Symbol

Access

INI

Description

31:16

RSVD

R

-

Reserved

15:0

CAN_TX_ERROR_FLAG

R/W

0x0

Indicate which message tx buffer have error detected, cpu can write 1 to clear

REG_CAN_TX_DONE

  • Name: CAN tx done for message buffers

  • Size: 32

  • Address offset: 038h

  • Read/write access: R/W

Flags which specific message buffer has successfully completed its transmission.

31:16 RSVD 15:0 CAN_TX_DONE

Bit

Symbol

Access

INI

Description

31:16

RSVD

R

-

Reserved

15:0

CAN_TX_DONE

R/W

0x0

Tx done for each message buffer

REG_CAN_RX_DONE

  • Name: CAN rx done for message buffers

  • Size: 32

  • Address offset: 03Ch

  • Read/write access: R/W

Flags which specific message buffer has successfully received a new message.

31:16 RSVD 15:0 CAN_RX_DONE

Bit

Symbol

Access

INI

Description

31:16

RSVD

R

-

Reserved

15:0

CAN_RX_DONE

R/W

0x0

Rx done for each message buffer

REG_CAN_TIME_STAMP

  • Name: Timestamp function

  • Size: 32

  • Address offset: 040h

  • Read/write access: R/W

Manages the internal counter used to apply timestamps to received/transmitted messages, including

its prescaler.

31 CAN_TIME_STAMP_EN 30:24 RSVD 23:16 CAN_TIME_STAMP_DIV 15:0 CAN_TIME_STAMP

Bit

Symbol

Access

INI

Description

31

CAN_TIME_STAMP_EN

R/W

0x0

Time stamp function enable and time stamp counter start

30:24

RSVD

R

-

Reserved

23:16

CAN_TIME_STAMP_DIV

R/W

0x0

Timer stamp conter prescalar

15:0

CAN_TIME_STAMP

R

0x0

Time stamp counter value, up count

REG_CAN_MB_TRIGGER

  • Name: CAN tx trigger by timer configuration

  • Size: 32

  • Address offset: 044h

  • Read/write access: R/W

Sets up a timer-based trigger mechanism to schedule message transmissions within a specific time

window.

31:25 RSVD 24 TX_TRIGGER_EN 23:16 TX_TRIGGER_CLOSE_OFFSET 15:0 TX_TRIGGER_BEGIN

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

TX_TRIGGER_EN

R/W

0x0

End of message buffer base address in RAM

23:16

TX_TRIGGER_CLOSE_OFFSET

R/W

0x0

End of trigger time = <$bit:tx_trigger_begin> + <$bit:tx_trigger_close_offset>

15:0

TX_TRIGGER_BEGIN

R/W

0x0

Start of trigger time

REG_CAN_RXDMA_CFG

  • Name: RX dma configuration

  • Size: 32

  • Address offset: 048h

  • Read/write access: R/W

Configures how the RX Direct Memory Access (DMA) operates

31:25 RSVD 24 CAN_RXDMA_OWNER 23:18 RSVD 17:16 CAN_RXDMA_SRC_MSIZE 15:14 RSVD 13:0 CAN_RXDMA_FRAME_SIZE

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_RXDMA_OWNER

R/W

0x0

Can rxdma owner is :

  • 0:GDMA

  • 1:CAN

23:18

RSVD

R

-

Reserved

17:16

CAN_RXDMA_SRC_MSIZE

R/W

0x1

Rx dma burst size:

  • ‘b00: dma burst size=1

  • ‘b01: dma burst size=4

  • ‘b10: dma burst size=8

  • ‘b11: dma burst size=16

15:14

RSVD

R

-

Reserved

13:0

CAN_RXDMA_FRAME_SIZE

R

0x2

Can rx dma data frame size = ceil(<rx_dma_data bytes number>/4 ), for example: rx_dma_data is 9~12 bytes, frame size is 3

REG_CAN_RX_DMA_DATA

  • Name: Register for dma access message buffe

  • Size: 32

  • Address offset: 04Ch

  • Read/write access: R

Acts as the data port from which the DMA controller reads received message payloads.

31:0 CAN_RX_DMA_DATA

Bit

Symbol

Access

INI

Description

31:0

CAN_RX_DMA_DATA

R

0x0

For DMA read received data

REG_CAN_SLEEP_MODE

  • Name: sleep mode request and wakeup pin digital filter

  • Size: 32

  • Address offset: 050h

  • Read/write access: R/W

Manages low-power sleep states, and configures the digital filter for the wakeup pin.

31:18 RSVD 17 CAN_SLEEP_STATE 16 CAN_SLEEP_EN 15:9 RSVD 8 CAN_WAKEPIN_FLT_EN 7:0 CAN_WAKEPIN_FLT_LENGTH

Bit

Symbol

Access

INI

Description

31:18

RSVD

R

-

Reserved

17

CAN_SLEEP_STATE

R

0x0

Can is sleep or not

  • 1: is

  • 0: isn’t

16

CAN_SLEEP_EN

R/W

0x0

Can sleep enable

  • 1:request can to sleep mode

  • 0:wakeup can

15:9

RSVD

R

-

Reserved

8

CAN_WAKEPIN_FLT_EN

R/W

0x0

Wakeup pin digital filter enable

7:0

CAN_WAKEPIN_FLT_LENGTH

R/W

0x1

Wakeup pin digital filter length

REG_CAN_TEST

  • Name: test configuration

  • Size: 32

  • Address offset: 054h

  • Read/write access: R/W

Enables special diagnostic modes, such as silent mode or internal/external loopback testing

31:2 RSVD 1:0 CAN_TEST_CFG

Bit

Symbol

Access

INI

Description

31:2

RSVD

R

-

Reserved

1:0

CAN_TEST_CFG

R/W

0x0

  • 2b’00: silence_mode

  • 2b’01: external loopback mode (enable can_tx_so )

  • 2b’10: internal loopback mode (can_tx_so tie 1)

  • 2b’11: reserved

REG_CAN_MB0_STS

  • Size: 32

  • Address offset: 100h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG0_RX_VLD 2 CAN_MSG0_RX_RDY 1 CAN_MSG0_TX_DONE 0 CAN_MSG0_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG0_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG0_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG0_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG0_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB1_STS

  • Size: 32

  • Address offset: 104h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG1_RX_VLD 2 CAN_MSG1_RX_RDY 1 CAN_MSG1_TX_DONE 0 CAN_MSG1_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG1_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG1_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG1_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG1_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB2_STS

  • Size: 32

  • Address offset: 108h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG2_RX_VLD 2 CAN_MSG2_RX_RDY 1 CAN_MSG2_TX_DONE 0 CAN_MSG2_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG2_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG2_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG2_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG2_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB3_STS

  • Size: 32

  • Address offset: 10Ch

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG3_RX_VLD 2 CAN_MSG3_RX_RDY 1 CAN_MSG3_TX_DONE 0 CAN_MSG3_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG3_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG3_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG3_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG3_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB4_STS

  • Size: 32

  • Address offset: 110h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG4_RX_VLD 2 CAN_MSG4_RX_RDY 1 CAN_MSG4_TX_DONE 0 CAN_MSG4_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG4_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG4_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG4_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG4_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB5_STS

  • Size: 32

  • Address offset: 114h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG5_RX_VLD 2 CAN_MSG5_RX_RDY 1 CAN_MSG5_TX_DONE 0 CAN_MSG5_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG5_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG5_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG5_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG5_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB6_STS

  • Size: 32

  • Address offset: 118h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG6_RX_VLD 2 CAN_MSG6_RX_RDY 1 CAN_MSG6_TX_DONE 0 CAN_MSG6_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG6_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG6_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG6_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG6_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB7_STS

  • Size: 32

  • Address offset: 11Ch

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG7_RX_VLD 2 CAN_MSG7_RX_RDY 1 CAN_MSG7_TX_DONE 0 CAN_MSG7_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG7_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG7_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG7_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG7_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB8_STS

  • Size: 32

  • Address offset: 120h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG8_RX_VLD 2 CAN_MSG8_RX_RDY 1 CAN_MSG8_TX_DONE 0 CAN_MSG8_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG8_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG8_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG8_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG8_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB9_STS

  • Size: 32

  • Address offset: 124h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG9_RX_VLD 2 CAN_MSG9_RX_RDY 1 CAN_MSG9_TX_DONE 0 CAN_MSG9_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG9_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG9_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG9_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG9_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB10_STS

  • Size: 32

  • Address offset: 128h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG10_RX_VLD 2 CAN_MSG10_RX_RDY 1 CAN_MSG10_TX_DONE 0 CAN_MSG10_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG10_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG10_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG10_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG10_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB11_STS

  • Size: 32

  • Address offset: 12Ch

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG11_RX_VLD 2 CAN_MSG11_RX_RDY 1 CAN_MSG11_TX_DONE 0 CAN_MSG11_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG11_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG11_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG11_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG11_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB12_STS

  • Size: 32

  • Address offset: 130h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG12_RX_VLD 2 CAN_MSG12_RX_RDY 1 CAN_MSG12_TX_DONE 0 CAN_MSG12_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG12_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG12_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG12_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG12_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB13_STS

  • Size: 32

  • Address offset: 134h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG13_RX_VLD 2 CAN_MSG13_RX_RDY 1 CAN_MSG13_TX_DONE 0 CAN_MSG13_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG13_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG13_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG13_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG13_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB14_STS

  • Size: 32

  • Address offset: 138h

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG14_RX_VLD 2 CAN_MSG14_RX_RDY 1 CAN_MSG14_TX_DONE 0 CAN_MSG14_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG14_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG14_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG14_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG14_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB15_STS

  • Size: 32

  • Address offset: 13Ch

  • Read/write access: R

Indicates the individual readiness, validity, and TX/RX status of a specific message buffer.

31:4 RSVD 3 CAN_MSG15_RX_VLD 2 CAN_MSG15_RX_RDY 1 CAN_MSG15_TX_DONE 0 CAN_MSG15_TX_REQ

Bit

Symbol

Access

INI

Description

31:4

RSVD

R

-

Reserved

3

CAN_MSG15_RX_VLD

R

0x0

New message have been received in the message buffer

2

CAN_MSG15_RX_RDY

R

0x0

The message buffer is ready for receiving a new message

1

CAN_MSG15_TX_DONE

R

0x0

Tx message in the message buffer finish sending

0

CAN_MSG15_TX_REQ

R

0x0

Tx message is pending for transmit

REG_CAN_MB0_CTRL

  • Size: 32

  • Address offset: 200h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG0_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG0_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG0_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG0_BA

R/W

9’d0

Message buffer base address in RAM

REG_CAN_MB1_CTRL

  • Size: 32

  • Address offset: 204h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG1_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG1_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG1_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG1_BA

R/W

9’d6

Message buffer base address in RAM

REG_CAN_MB2_CTRL

  • Size: 32

  • Address offset: 208h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG2_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG2_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG2_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG2_BA

R/W

9’d12

Message buffer base address in RAM

REG_CAN_MB3_CTRL

  • Size: 32

  • Address offset: 20Ch

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG3_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG3_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG3_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG3_BA

R/W

9’d18

Message buffer base address in RAM

REG_CAN_MB4_CTRL

  • Size: 32

  • Address offset: 210h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG4_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG4_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG4_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG4_BA

R/W

9’d24

Message buffer base address in RAM

REG_CAN_MB5_CTRL

  • Size: 32

  • Address offset: 214h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG5_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG5_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG5_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG5_BA

R/W

9’d30

Message buffer base address in RAM

REG_CAN_MB6_CTRL

  • Size: 32

  • Address offset: 218h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG6_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG6_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG6_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG6_BA

R/W

9’d36

Message buffer base address in RAM

REG_CAN_MB7_CTRL

  • Size: 32

  • Address offset: 21Ch

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG7_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG7_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG7_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG7_BA

R/W

9’d42

Message buffer base address in RAM

REG_CAN_MB8_CTRL

  • Size: 32

  • Address offset: 220h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG8_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG8_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG8_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG8_BA

R/W

9’d48

Message buffer base address in RAM

REG_CAN_MB9_CTRL

  • Size: 32

  • Address offset: 224h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG9_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG9_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG9_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG9_BA

R/W

9’d54

Message buffer base address in RAM

REG_CAN_MB10_CTRL

  • Size: 32

  • Address offset: 228h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG10_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG10_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG10_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG10_BA

R/W

9’d60

Message buffer base address in RAM

REG_CAN_MB11_CTRL

  • Size: 32

  • Address offset: 22Ch

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG11_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG11_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG11_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG11_BA

R/W

9’d66

Message buffer base address in RAM

REG_CAN_MB12_CTRL

  • Size: 32

  • Address offset: 230h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG12_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG12_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG12_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG12_BA

R/W

9’d72

Message buffer base address in RAM

REG_CAN_MB13_CTRL

  • Size: 32

  • Address offset: 234h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG13_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG13_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG13_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG13_BA

R/W

9’d78

Message buffer base address in RAM

REG_CAN_MB14_CTRL

  • Size: 32

  • Address offset: 238h

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG14_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG14_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG14_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG14_BA

R/W

9’d84

Message buffer base address in RAM

REG_CAN_MB15_CTRL

  • Size: 32

  • Address offset: 23Ch

  • Read/write access: R/W

Configures the starting address in RAM and enables DMA functionality for a specific message buffer.

31:25 RSVD 24 CAN_MSG15_RXDMA_EN 23:9 RSVD 8:0 CAN_MSG15_BA

Bit

Symbol

Access

INI

Description

31:25

RSVD

R

-

Reserved

24

CAN_MSG15_RXDMA_EN

R/W

0x0

Dma enable when the message buffer used as rx

23:9

RSVD

R

-

Reserved

8:0

CAN_MSG15_BA

R/W

9’d90

Message buffer base address in RAM

REG_CAN_MB_BA_END

  • Size: 32

  • Address offset: 2F0h

  • Read/write access: R/W

Defines the ending boundary address in RAM allocated for message buffers.

31:10 RSVD 9:0 CAN_MSG_BA_END

Bit

Symbol

Access

INI

Description

31:10

RSVD

R

-

Reserved

9:0

CAN_MSG_BA_END

R/W

10’d96

End of message buffer base address in RAM

REG_CAN_RAM_DATA_15

  • Name: CAN data

  • Size: 32

  • Address offset: 300h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_15_3 23:16 CAN_RAM_DATA_15_2 15:8 CAN_RAM_DATA_15_1 7:0 CAN_RAM_DATA_15_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_15_3

R/W

0x0

Data_byte 4*15+3

23:16

CAN_RAM_DATA_15_2

R/W

0x0

Data_byte 4*15+2

15:8

CAN_RAM_DATA_15_1

R/W

0x0

Data_byte 4*15+1

7:0

CAN_RAM_DATA_15_0

R/W

0x0

Data_byte 4*15+0

REG_CAN_RAM_DATA_14

  • Name: CAN data

  • Size: 32

  • Address offset: 304h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_14_3 23:16 CAN_RAM_DATA_14_2 15:8 CAN_RAM_DATA_14_1 7:0 CAN_RAM_DATA_14_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_14_3

R/W

0x0

Data_byte 4*14+3

23:16

CAN_RAM_DATA_14_2

R/W

0x0

Data_byte 4*14+2

15:8

CAN_RAM_DATA_14_1

R/W

0x0

Data_byte 4*14+1

7:0

CAN_RAM_DATA_14_0

R/W

0x0

Data_byte 4*14+0

REG_CAN_RAM_DATA_13

  • Name: CAN data

  • Size: 32

  • Address offset: 308h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_13_3 23:16 CAN_RAM_DATA_13_2 15:8 CAN_RAM_DATA_13_1 7:0 CAN_RAM_DATA_13_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_13_3

R/W

0x0

Data_byte 4*13+3

23:16

CAN_RAM_DATA_13_2

R/W

0x0

Data_byte 4*13+2

15:8

CAN_RAM_DATA_13_1

R/W

0x0

Data_byte 4*13+1

7:0

CAN_RAM_DATA_13_0

R/W

0x0

Data_byte 4*13+0

REG_CAN_RAM_DATA_12

  • Name: CAN data

  • Size: 32

  • Address offset: 30Ch

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_12_3 23:16 CAN_RAM_DATA_12_2 15:8 CAN_RAM_DATA_12_1 7:0 CAN_RAM_DATA_12_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_12_3

R/W

0x0

Data_byte 4*12+3

23:16

CAN_RAM_DATA_12_2

R/W

0x0

Data_byte 4*12+2

15:8

CAN_RAM_DATA_12_1

R/W

0x0

Data_byte 4*12+1

7:0

CAN_RAM_DATA_12_0

R/W

0x0

Data_byte 4*12+0

REG_CAN_RAM_DATA_11

  • Name: CAN data

  • Size: 32

  • Address offset: 310h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_11_3 23:16 CAN_RAM_DATA_11_2 15:8 CAN_RAM_DATA_11_1 7:0 CAN_RAM_DATA_11_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_11_3

R/W

0x0

Data_byte 4*11+3

23:16

CAN_RAM_DATA_11_2

R/W

0x0

Data_byte 4*11+2

15:8

CAN_RAM_DATA_11_1

R/W

0x0

Data_byte 4*11+1

7:0

CAN_RAM_DATA_11_0

R/W

0x0

Data_byte 4*11+0

REG_CAN_RAM_DATA_10

  • Name: CAN data

  • Size: 32

  • Address offset: 314h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_10_3 23:16 CAN_RAM_DATA_10_2 15:8 CAN_RAM_DATA_10_1 7:0 CAN_RAM_DATA_10_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_10_3

R/W

0x0

Data_byte 4*10+3

23:16

CAN_RAM_DATA_10_2

R/W

0x0

Data_byte 4*10+2

15:8

CAN_RAM_DATA_10_1

R/W

0x0

Data_byte 4*10+1

7:0

CAN_RAM_DATA_10_0

R/W

0x0

Data_byte 4*10+0

REG_CAN_RAM_DATA_9

  • Name: CAN data

  • Size: 32

  • Address offset: 318h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_9_3 23:16 CAN_RAM_DATA_9_2 15:8 CAN_RAM_DATA_9_1 7:0 CAN_RAM_DATA_9_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_9_3

R/W

0x0

Data_byte 4*9+3

23:16

CAN_RAM_DATA_9_2

R/W

0x0

Data_byte 4*9+2

15:8

CAN_RAM_DATA_9_1

R/W

0x0

Data_byte 4*9+1

7:0

CAN_RAM_DATA_9_0

R/W

0x0

Data_byte 4*9+0

REG_CAN_RAM_DATA_8

  • Name: CAN data

  • Size: 32

  • Address offset: 31Ch

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_8_3 23:16 CAN_RAM_DATA_8_2 15:8 CAN_RAM_DATA_8_1 7:0 CAN_RAM_DATA_8_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_8_3

R/W

0x0

Data_byte 4*8+3

23:16

CAN_RAM_DATA_8_2

R/W

0x0

Data_byte 4*8+2

15:8

CAN_RAM_DATA_8_1

R/W

0x0

Data_byte 4*8+1

7:0

CAN_RAM_DATA_8_0

R/W

0x0

Data_byte 4*8+0

REG_CAN_RAM_DATA_7

  • Name: CAN data

  • Size: 32

  • Address offset: 320h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_7_3 23:16 CAN_RAM_DATA_7_2 15:8 CAN_RAM_DATA_7_1 7:0 CAN_RAM_DATA_7_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_7_3

R/W

0x0

Data_byte 4*7+3

23:16

CAN_RAM_DATA_7_2

R/W

0x0

Data_byte 4*7+2

15:8

CAN_RAM_DATA_7_1

R/W

0x0

Data_byte 4*7+1

7:0

CAN_RAM_DATA_7_0

R/W

0x0

Data_byte 4*7+0

REG_CAN_RAM_DATA_6

  • Name: CAN data

  • Size: 32

  • Address offset: 324h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_6_3 23:16 CAN_RAM_DATA_6_2 15:8 CAN_RAM_DATA_6_1 7:0 CAN_RAM_DATA_6_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_6_3

R/W

0x0

Data_byte 4*6+3

23:16

CAN_RAM_DATA_6_2

R/W

0x0

Data_byte 4*6+2

15:8

CAN_RAM_DATA_6_1

R/W

0x0

Data_byte 4*6+1

7:0

CAN_RAM_DATA_6_0

R/W

0x0

Data_byte 4*6+0

REG_CAN_RAM_DATA_5

  • Name: CAN data

  • Size: 32

  • Address offset: 328h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_5_3 23:16 CAN_RAM_DATA_5_2 15:8 CAN_RAM_DATA_5_1 7:0 CAN_RAM_DATA_5_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_5_3

R/W

0x0

Data_byte 4*5+3

23:16

CAN_RAM_DATA_5_2

R/W

0x0

Data_byte 4*5+2

15:8

CAN_RAM_DATA_5_1

R/W

0x0

Data_byte 4*5+1

7:0

CAN_RAM_DATA_5_0

R/W

0x0

Data_byte 4*5+0

REG_CAN_RAM_DATA_4

  • Name: CAN data

  • Size: 32

  • Address offset: 32Ch

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_4_3 23:16 CAN_RAM_DATA_4_2 15:8 CAN_RAM_DATA_4_1 7:0 CAN_RAM_DATA_4_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_4_3

R/W

0x0

Data_byte 4*4+3

23:16

CAN_RAM_DATA_4_2

R/W

0x0

Data_byte 4*4+2

15:8

CAN_RAM_DATA_4_1

R/W

0x0

Data_byte 4*4+1

7:0

CAN_RAM_DATA_4_0

R/W

0x0

Data_byte 4*4+0

REG_CAN_RAM_DATA_3

  • Name: CAN data

  • Size: 32

  • Address offset: 330h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_3_3 23:16 CAN_RAM_DATA_3_2 15:8 CAN_RAM_DATA_3_1 7:0 CAN_RAM_DATA_3_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_3_3

R/W

0x0

Data_byte 4*3+3

23:16

CAN_RAM_DATA_3_2

R/W

0x0

Data_byte 4*3+2

15:8

CAN_RAM_DATA_3_1

R/W

0x0

Data_byte 4*3+1

7:0

CAN_RAM_DATA_3_0

R/W

0x0

Data_byte 4*3+0

REG_CAN_RAM_DATA_2

  • Name: CAN data

  • Size: 32

  • Address offset: 334h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_2_3 23:16 CAN_RAM_DATA_2_2 15:8 CAN_RAM_DATA_2_1 7:0 CAN_RAM_DATA_2_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_2_3

R/W

0x0

Data_byte 4*2+3

23:16

CAN_RAM_DATA_2_2

R/W

0x0

Data_byte 4*2+2

15:8

CAN_RAM_DATA_2_1

R/W

0x0

Data_byte 4*2+1

7:0

CAN_RAM_DATA_2_0

R/W

0x0

Data_byte 4*2+0

REG_CAN_RAM_DATA_1

  • Name: CAN data

  • Size: 32

  • Address offset: 338h

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_1_3 23:16 CAN_RAM_DATA_1_2 15:8 CAN_RAM_DATA_1_1 7:0 CAN_RAM_DATA_1_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_1_3

R/W

0x0

Data_byte 4*1+3

23:16

CAN_RAM_DATA_1_2

R/W

0x0

Data_byte 4*1+2

15:8

CAN_RAM_DATA_1_1

R/W

0x0

Data_byte 4*1+1

7:0

CAN_RAM_DATA_1_0

R/W

0x0

Data_byte 4*1+0

REG_CAN_RAM_DATA_0

  • Name: CAN data

  • Size: 32

  • Address offset: 33Ch

  • Read/write access: R/W

Serves as the register interface to read or write the actual data payload (up to 64 bytes) into the

RAM.

31:24 CAN_RAM_DATA_0_3 23:16 CAN_RAM_DATA_0_2 15:8 CAN_RAM_DATA_0_1 7:0 CAN_RAM_DATA_0_0

Bit

Symbol

Access

INI

Description

31:24

CAN_RAM_DATA_0_3

R/W

0x0

Data_byte 4*0+3

23:16

CAN_RAM_DATA_0_2

R/W

0x0

Data_byte 4*0+2

15:8

CAN_RAM_DATA_0_1

R/W

0x0

Data_byte 4*0+1

7:0

CAN_RAM_DATA_0_0

R/W

0x0

Data_byte 4*0+0

REG_CAN_RAM_ARB

  • Name: CAN message buffer arb field configuration

  • Size: 32

  • Address offset: 340h

  • Read/write access: R/W

Configures the message identifier (ID), format (IDE), and frame type (RTR) for a message buffer

being written to or read from RAM.

31 RSVD 30 CAN_RAM_RTR 29 CAN_RAM_IDE 28:0 CAN_RAM_ID

Bit

Symbol

Access

INI

Description

31

RSVD

R

-

Reserved

30

CAN_RAM_RTR

R/W

0x0

Can frame RTR bit, determine DATA or REMOTE frame

29

CAN_RAM_IDE

R/W

0x0

Can frame IDE bit, determine standard or extend format

28:0

CAN_RAM_ID

R/W

0x0

Can frame ID, including high 11 bit standard ID and low 18 bit extend ID

REG_CAN_RAM_MASK

  • Name: CAN message buffer arb field mask configuration

  • Size: 32

  • Address offset: 344h

  • Read/write access: R/W

Configures the acceptance filter masks, defining which bits of an incoming message ID must match to

be accepted into the buffer.

31 RSVD 30 CAN_RAM_RTR_MASK 29 CAN_RAM_IDE_MASK 28:0 CAN_RAM_ID_MASK

Bit

Symbol

Access

INI

Description

31

RSVD

R

-

Reserved

30

CAN_RAM_RTR_MASK

R/W

0x0

Can frame RTR mask, 0 means don’t care, 1 means the bit should match

29

CAN_RAM_IDE_MASK

R/W

0x0

Can frame IDE mask, 0 means don’t care, 1 means the bit should match

28:0

CAN_RAM_ID_MASK

R/W

0x0

Can frame ID mask, 0 means the ID bit in CAN_RAM_ARB don’t care, 1 means the bit should match.

REG_CAN_RAM_CS

  • Name: CAN message type control

  • Size: 32

  • Address offset: 348h

  • Read/write access: R/W

Configures control and status attributes of the message, such as Data Length Code (DLC) and

direction (TX/RX).

31:16 CAN_RAM_TIMESTAMP 15:7 RSVD 6 CAN_RAM_AUTOREPLY 5 CAN_RAM_RXTX 4 CAN_RAM_LOST 3:0 CAN_RAM_DLC

Bit

Symbol

Access

INI

Description

31:16

CAN_RAM_TIMESTAMP

R/W

0x0

The received message time stamp

15:7

RSVD

R

-

Reserved

6

CAN_RAM_AUTOREPLY

R/W

0x0

Set the message buffer with remote frame auto reply function

5

CAN_RAM_RXTX

R/W

0x0

Can frame RX or TX, 0 is for RX, 1 is for TX

4

CAN_RAM_LOST

R/W

0x0

Data have lost in the read buffer, means more than one frame have beed received since last read; only avaliable when rx FIFO is disabled

3:0

CAN_RAM_DLC

R/W

0x0

Data length

REG_CAN_RAM_CMD

  • Name: CAN message buffer access control

  • Size: 32

  • Address offset: 34Ch

  • Read/write access: R/W

Executes the command to transfer data between the CAN_RAM_* registers and the actual internal SRAM

for a specified message buffer.

31 CAN_RAM_START 30 CAN_RAM_DIR 29 CAN_RAM_BUFFER_EN 28:27 RSVD 26 CAN_RAM_ACC_DATA15 25 CAN_RAM_ACC_DATA14 24 CAN_RAM_ACC_DATA13 23 CAN_RAM_ACC_DATA12 22 CAN_RAM_ACC_DATA11 21 CAN_RAM_ACC_DATA10 20 CAN_RAM_ACC_DATA9 19 CAN_RAM_ACC_DATA8 18 CAN_RAM_ACC_DATA7 17 CAN_RAM_ACC_DATA6 16 CAN_RAM_ACC_DATA5 15 CAN_RAM_ACC_DATA4 14 CAN_RAM_ACC_DATA3 13 CAN_RAM_ACC_DATA2 12 CAN_RAM_ACC_DATA1 11 CAN_RAM_ACC_DATA0 10 CAN_RAM_ACC_ARB 9 CAN_RAM_ACC_CS 8 CAN_RAM_ACC_MASK 7:0 CAN_RAM_ACC_NUM

Bit

Symbol

Access

INI

Description

31

CAN_RAM_START

R/W

0x0

Start to exchange data with RAM, the bit will clear automatically after the data change is finshed.

30

CAN_RAM_DIR

R/W

0x0

0 is for read from RAM to CAN_RAM_* registers, 1 is for write from CAN_RAM_* to RAM

29

CAN_RAM_BUFFER_EN

R/W

0x0

Enable the can_ram_acc_num specified message buffer for rx/tx

28:27

RSVD

R

-

Reserved

26

CAN_RAM_ACC_DATA15

R/W

0x0

Access CAN_RAM_DATA_15 field, the field will exchange with RAM space

25

CAN_RAM_ACC_DATA14

R/W

0x0

Access CAN_RAM_DATA_14 field, the field will exchange with RAM space

24

CAN_RAM_ACC_DATA13

R/W

0x0

Access CAN_RAM_DATA_13 field, the field will exchange with RAM space

23

CAN_RAM_ACC_DATA12

R/W

0x0

Access CAN_RAM_DATA_12 field, the field will exchange with RAM space

22

CAN_RAM_ACC_DATA11

R/W

0x0

Access CAN_RAM_DATA_11 field, the field will exchange with RAM space

21

CAN_RAM_ACC_DATA10

R/W

0x0

Access CAN_RAM_DATA_10 field, the field will exchange with RAM space

20

CAN_RAM_ACC_DATA9

R/W

0x0

Access CAN_RAM_DATA_9 field, the field will exchange with RAM space

19

CAN_RAM_ACC_DATA8

R/W

0x0

Access CAN_RAM_DATA_8 field, the field will exchange with RAM space

18

CAN_RAM_ACC_DATA7

R/W

0x0

Access CAN_RAM_DATA_7 field, the field will exchange with RAM space

17

CAN_RAM_ACC_DATA6

R/W

0x0

Access CAN_RAM_DATA_6 field, the field will exchange with RAM space

16

CAN_RAM_ACC_DATA5

R/W

0x0

Access CAN_RAM_DATA_5 field, the field will exchange with RAM space

15

CAN_RAM_ACC_DATA4

R/W

0x0

Access CAN_RAM_DATA_4 field, the field will exchange with RAM space

14

CAN_RAM_ACC_DATA3

R/W

0x0

Access CAN_RAM_DATA_3 field, the field will exchange with RAM space

13

CAN_RAM_ACC_DATA2

R/W

0x0

Access CAN_RAM_DATA_2 field, the field will exchange with RAM space

12

CAN_RAM_ACC_DATA1

R/W

0x0

Access CAN_RAM_DATA_1 field, the field will exchange with RAM space

11

CAN_RAM_ACC_DATA0

R/W

0x0

Access CAN_RAM_DATA_0 field, the field will exchange with RAM space

10

CAN_RAM_ACC_ARB

R/W

0x0

Access CAN_RAM_ARB field, the field will exchange with RAM space

9

CAN_RAM_ACC_CS

R/W

0x0

Access CAN_RAM_CS field, the field will exchange with RAM space

8

CAN_RAM_ACC_MASK

R/W

0x0

Access CAN_RAM_MASK field, the field will exchange with RAM space

7:0

CAN_RAM_ACC_NUM

R/W

0x0

Access buffer number

REG_CAN_DBG_PORT

  • Name: debug register

  • Size: 32

  • Address offset: 3F8h

  • Read/write access: R/W

Selects and enables internal hardware signals to be routed to debug pins for hardware

troubleshooting.

31:9 RSVD 8 CAN_DBG_EN 7:0 CAN_DBG_SEL

Bit

Symbol

Access

INI

Description

31:9

RSVD

R

-

Reserved

8

CAN_DBG_EN

R/W

0x0

Debug port enable

7:0

CAN_DBG_SEL

R/W

0x0

Debug port selection

REG_CAN_DUMMY

  • Name: dummy register

  • Size: 32

  • Address offset: 3FCh

  • Read/write access: R/W

A reserved placeholder register used for hardware alignment or future expansion.

31:0 DUMMY

Bit

Symbol

Access

INI

Description

31:0

DUMMY

R/W

0x0

Rsvd for hw