寄存器
请查看
寄存器访问类型
,了解 Access 列缩写的含义。
Base Address: 0x41010000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
||
004h |
R/W |
||
008h |
R |
||
030h |
R/W |
||
038h |
R/W |
||
03Ch |
R/W |
||
040h |
R |
||
044h |
R |
||
048h |
R/W |
||
04Ch |
R/W |
||
050h |
R |
||
060h |
R/W |
||
064h |
R |
||
068h |
R/W |
||
06Ch |
R |
||
078h |
R |
REG_GPIO_DR
Name: PortA/B data register
Size: 32
Address offset: 000h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORT_DATA |
R/W |
0 |
Values written to this register are output on the I/O signals for Portx if the corresponding data direction bits for Portx are set to output mode and the corresponding control bit for Portx is set to software mode. The value read back equals to the last value written to this register. |
REG_GPIO_DDR
Name: PortA/B data direction register
Size: 32
Address offset: 004h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORT_DATA_DIRECTION |
R/W |
0 |
Values written to this register independently control the direction of the corresponding data bit in Portx. The default direction can be configured as input or output after system reset through the GPIO_DFLT_DIR_x parameter.
|
REG_GPIO_CTL
Name: PortA/B data source register
Size: 32
Address offset: 008h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_GPIO_INT_EN
Name: PortA/B interrupt enable register
Size: 32
Address offset: 030h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EN |
R/W |
0 |
Allows each bit of Portx to be configured for interrupts. By default, the generation of interrupts is disabled. Whenever a 1 is written to a bit of this register, it configures the corresponding bit on Portx to become an interrupt; otherwise, Portx operates as a normal GPIO signal. Interrupts are disabled on the corresponding bits of Portx if the corresponding data direction register is set to output or if Portx mode is set to hardware.
|
REG_GPIO_INT_TYPE
Name: PortA/B interrupt trigger type register
Size: 32
Address offset: 038h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_TYPE |
R/W |
0 |
Controls the type of interrupt that can occur on Portx. Whenever a 0 is written to a bit of this register, it configures the interrupt type to be level-sensitive; otherwise, it is edge-sensitive.
|
REG_GPIO_INT_POLARITY
Name: PortA/B interrupt polarity register
Size: 32
Address offset: 03Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_POLARITY |
R/W |
0 |
Controls the polarity of edge or level sensitivity that can occur on input of Portx. Whenever a 0 is written to a bit of this register, it configures the interrupt type to falling-edge or active-low sensitive; otherwise, it is rising-edge or active-high sensitive.
|
REG_GPIO_INT_STATUS
Name: PortA/B interrupt status register
Size: 32
Address offset: 040h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_STATUS |
R |
0 |
Interrupt status of Portx. |
REG_GPIO_INT_STATUS_RAW
Name: PortA/B raw interrupt status register
Size: 32
Address offset: 044h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_RAW_INT_STATUS |
R |
0 |
Raw interrupt status of Portx (premasking bits). |
REG_GPIO_DEBOUNCE
Name: PortA/B interrupt debounce register
Size: 32
Address offset: 048h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_DEBOUNCE_EN |
R/W |
0 |
Controls whether an external signal that is the source of an interrupt needs to be debounced to remove any spurious glitches. Writing a 1 to a bit in this register enables the debouncing circuitry. A signal must be valid for two periods of an external clock before it is internally processed.
This register is available only if Portx is configured to generate interrupts (GPIO_PORTA_INTR = Include(1)) and when the debounce logic is included (GPIO_DEBOUNCE = Include(1)). |
REG_GPIO_INT_EOI
Name: PortA/B edge type interrupt clear register
Size: 32
Address offset: 04Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EOI |
R/W |
0 |
Controls the clearing of edge type interrupts from Portx. When a 1 is written into a corresponding bit of this register, the interrupt is cleared. All interrupts are cleared when Portx is not configured for interrupts.
|
REG_GPIO_EXT_PORT
Name: External PortA/B data register
Size: 32
Address offset: 050h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_EXT_PORTA |
R |
0 |
When Portx is configured as Input, then reading this location reads the values on the signal. When the data direction of Portx is set as output, reading this location reads the data register for Portx. |
REG_GPIO_ITN_LS_SYNC
Name: PortA/B level interrupt synchronization
Size: 32
Address offset: 060h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
GPIO_LEVEL_SYNC |
R/W |
0 |
Writing a 1 to this register results in all level-sensitive interrupts being synchronized to pclk_intr.
|
REG_GPIO_ID_CODE
Name: PortA/B GPIO ID code register
Size: 32
Address offset: 064h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_ID_CODE |
R |
32'h1 |
This register is available only if Portx is configured to generate interrupts (GPIO_PORTx_INTR = Include(1)) and interrupt detection is configured to generate on both rising and falling edges of external input signal (GPIO_INT_BOTH_EDGE=Include(1)). |
REG_GPIO_INT_BOTHEDGE
Name: PortA/B both edge interrupt register
Size: 32
Address offset: 068h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_BOTHEDGE |
R/W |
0 |
Controls the edge types of interrupt that can occur on Portx. Whenever a particular bit is programmed to 1, it enables the generation of interrupt on both the rising edge and falling edge of an external input signal corresponding to that bit on Portx. The values programmed in the registers gpio_intype_level and gpio_int_polarity for this particular bit are not considered when the corresponding bit of this register is set to 1. Whenever a particular bit is programmed to 0, the interrupt type depends on the value of the corresponding bits in the gpio_inttype_level and gpio_int_polarity registers.
|
REG_GPIO_VER_ID_CODE
Name: PortA/B GPIO component version register
Size: 32
Address offset: 06Ch
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_VER_ID_CODE |
R |
32'h3231302A |
ASCII value for each number in the version, followed by *. For example, 32_30_31_2A represents the version 2.01*. |
REG_GPIO_DB_DIV_CONFIG
Size: 32
Address offset: 078h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
Base Address: 0x4101A000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
||
004h |
R/W |
||
008h |
R |
||
030h |
R/W |
||
034h |
R/W |
||
038h |
R/W |
||
03Ch |
R/W |
||
040h |
R |
||
044h |
R |
||
048h |
R/W |
||
04Ch |
R/W |
||
050h |
R |
||
060h |
R/W |
||
064h |
R |
||
068h |
R/W |
||
06Ch |
R |
REG_GPIO_DR
Name: PortA/B data register
Size: 32
Address offset: 000h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORT_DATA |
R/W |
0 |
Values written to this register are output on the I/O signals for Portx if the corresponding data direction bits for Portx are set to Output mode and the corresponding control bit for Portx is set to software mode. The value read back is equal to the last value written to this register. Valid bits is: PortA[31:0] and PortB[19:0]. |
REG_GPIO_DDR
Name: PortA/B data direction register
Size: 32
Address offset: 004h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORT_DATA_DIRECTION |
R/W |
0 |
Values written to this register independently control the direction of the corresponding data bit in Portx. The default direction can be configured as input or output after system reset through the GPIO_DFLT_DIR_x parameter.
Valid bits is: PortA[31:0] and PortB[19:0]. |
REG_GPIO_CTL
Name: PortA/B data source register
Size: 32
Address offset: 008h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_GPIO_INT_EN
Name: PortA/B interrupt enable register
Size: 32
Address offset: 030h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EN |
R/W |
0 |
Allows each bit of Portx to be configured for interrupts. By default, the generation of interrupts is disabled. Whenever a 1 is written to a bit of this register, it configures the corresponding bit on Portx to become an interrupt; otherwise, Portx operates as a normal GPIO signal. Interrupts are disabled on the corresponding bits of Portx if the corresponding data direction register is set to Output or if Portx mode is set to Hardware.
|
REG_GPIO_INT_MASK
Name: PortA/B interrupt mask register
Size: 32
Address offset: 034h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_MASK |
R/W |
0 |
Controls whether an interrupt on Portx can create an interrupt for the interrupt controller by not masking it. By default, all interrupts bits are unmasked. Whenever a 1 is written to a bit in this register, it masks the interrupt generation capability for this signal; otherwise interrupts are allowed through. The unmasked status can be read as well as the resultant status after masking.
|
REG_GPIO_INT_TYPE
Name: PortA interrupt trigger type register
Size: 32
Address offset: 038h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_TYPE |
R/W |
0 |
Controls the type of interrupt that can occur on Portx. Whenever a 0 is written to a bit of this register, it configures the interrupt type to be level-sensitive; otherwise, it is edge-sensitive.
|
REG_GPIO_INT_POLARITY
Name: PortA interrupt polarity register
Size: 32
Address offset: 03Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_POLARITY |
R/W |
0 |
Controls the polarity of edge or level sensitivity that can occur on input of Portx. Whenever a 0 is written to a bit of this register, it configures the interrupt type to falling-edge or active-low sensitive; otherwise, it is rising-edge or active-high sensitive.
|
REG_GPIO_INT_STATUS
Name: PortA/B interrupt status register
Size: 32
Address offset: 040h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_STATUS |
R |
0 |
Interrupt status of Portx. |
REG_GPIO_INT_STATUS_RAW
Name: PortA/B raw interrupt status register
Size: 32
Address offset: 044h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_RAW_INT_STATUS |
R |
0 |
Raw interrupt status of Portx (premasking bits). |
REG_GPIO_DEBOUNCE
Name: PortA/B interrupt debounce register
Size: 32
Address offset: 048h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_DEBOUNCE_EN |
R/W |
0 |
Controls whether an external signal that is the source of an interrupt needs to be debounced to remove any spurious glitches. Writing a 1 to a bit in this register enables the debouncing circuitry. A signal must be valid for two periods of an external clock before it is internally Processed.
This register is available only if Portx is configured to generate interrupts (GPIO_PORTA_INTR = Include (1)) and when the debounce logic is included (GPIO_DEBOUNCE = Include (1)). |
REG_GPIO_INT_EOI
Name: PortA/B edge type interrupt clear register
Size: 32
Address offset: 04Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EOI |
R/W |
0 |
Controls the clearing of edge type interrupts from Portx. When a 1 is written into a corresponding bit of this register, the interrupt is cleared. All interrupts are cleared when Portx is not configured for interrupts.
|
REG_GPIO_EXT_PORT
Name: External PortA/B data register
Size: 32
Address offset: 050h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_EXT_PORTA |
R |
0 |
When Portx is configured as Input, then reading this location reads the values on the signal. When the data direction of Portx is set as Output, reading this location reads the data register for Portx. |
REG_GPIO_ITN_LS_SYNC
Name: PortA/B level interrupt synchronization
Size: 32
Address offset: 060h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
GPIO_LEVEL_SYNC |
R/W |
0 |
Writing a 1 to this register results in all level-sensitive interrupts being synchronized to pclk_intr.
|
REG_GPIO_ID_CODE
Name: PortA/B GPIO ID code register
Size: 32
Address offset: 064h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_ID_CODE |
R |
32'h1 |
This register is available only if PortxA/B is configured to generate interrupts (GPIO_PORTx_INTR = Include (1)) and interrupt detection is configured to generate on both rising and falling edges of external input signal (GPIO_INT_BOTH_EDGE=Include (1)). |
REG_GPIO_INT_BOTHEDGE
Name: PortA/B both edge interrupt register
Size: 32
Address offset: 068h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_BOTHEDGE |
R/W |
0 |
Controls the edge types of interrupt that can occur on Portx. Whenever a particular bit is programmed to 1, it enables the generation of interrupt on both the rising edge and falling edge of an external input signal corresponding to that bit on PortA. The values programmed in the registers gpio_intype_level and gpio_int_polarity for this particular bit are not considered when the corresponding bit of this register is set to 1. Whenever a particular bit is programmed to 0, the interrupt type depends on the value of the corresponding bits in the gpio_inttype_level and gpio_int_polarity registers.
|
REG_GPIO_VER_ID_CODE
Name: PortA/B GPIO component version register
Size: 32
Address offset: 06Ch
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_VER_ID_CODE |
R |
32'h3231302A |
ASCII value for each number in the version, followed by *. For example 32_30_31_2A represents the version 2.01*. Reset Value: See the releases table in the Release Notes. |
REGISTER_CONTENTS=RTL8720E
REGISTER_CONTENTS=RTL8720E
REGISTER_CONTENTS=RTL8720E
Base Address: 0x4200D000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
||
004h |
R/W |
||
008h |
R |
||
030h |
R/W |
||
034h |
R/W |
||
038h |
R/W |
||
03Ch |
R/W |
||
040h |
R |
||
044h |
R |
||
048h |
R/W |
||
04Ch |
R/W |
||
050h |
R |
||
060h |
R/W |
||
064h |
R |
||
068h |
R/W |
||
06Ch |
R |
||
078h |
R/W |
REG_GPIO_DR
Name: PortA data register
Size: 32
Address offset: 000h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORTA_DATA |
R/W |
0 |
Values written to this register are output on the I/O signals for Portx if the corresponding data direction bits for Portx are set to Output mode and the corresponding control bit for Portx is set to software mode. The value read back is equal to the last value written to this register. |
REG_GPIO_DDR
Name: PortA data direction register
Size: 32
Address offset: 004h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORTA_DATA_DIRECTION |
R/W |
0 |
Values written to this register independently control the direction of the corresponding data bit in Portx. The default direction can be configured as input or output after system reset through the GPIO_DFLT_DIR_x parameter.
|
REG_GPIO_CTL
Name: PortA data source register
Size: 32
Address offset: 008h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_GPIO_INT_EN
Name: PortA/B/C interrupt enable register
Size: 32
Address offset: 030h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EN |
R/W |
0 |
Allows each bit of Portx to be configured for interrupts. By default, the generation of interrupts is disabled. Whenever a 1 is written to a bit of this register, it configures the corresponding bit on Portx to become an interrupt; otherwise, Portx operates as a normal GPIO signal. Interrupts are disabled on the corresponding bits of Portx if the corresponding data direction register is set to Output or if Portx mode is set to Hardware.
|
REG_GPIO_INT_MASK
Name: PortA/B/C interrupt mask register
Size: 32
Address offset: 034h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_MASK |
R/W |
0 |
Controls whether an interrupt on Portx can create an interrupt for the interrupt controller by not masking it. By default, all interrupts bits are unmasked. Whenever a 1 is written to a bit in this register, it masks the interrupt generation capability for this signal; otherwise interrupts are allowed through. The unmasked status can be read as well as the resultant status after masking.
|
REG_GPIO_INT_TYPE
Name: PortA interrupt trigger type register
Size: 32
Address offset: 038h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_TYPE |
R/W |
0 |
Controls the type of interrupt that can occur on Portx. Whenever a 0 is written to a bit of this register, it configures the Interrupt type to be level-sensitive; otherwise, it is edge-sensitive.
|
REG_GPIO_INT_POLARITY
Name: PortA interrupt polarity register
Size: 32
Address offset: 03Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_POLARITY |
R/W |
0 |
Controls the polarity of edge or level sensitivity that can occur on input of Portx. Whenever a 0 is written to a bit of this register, it configures the interrupt type to falling-edge or active-low sensitive; otherwise, it is rising-edge or active-high sensitive.
|
REG_GPIO_INT_STATUS
Name: PortA/B/C interrupt status register
Size: 32
Address offset: 040h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_STATUS |
R |
0 |
Interrupt status of Portx. |
REG_GPIO_INT_STATUS_RAW
Name: PortA/B/C raw interrupt status register
Size: 32
Address offset: 044h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_RAW_INT_STATUS |
R |
0 |
Raw interrupt status of Portx (premasking bits). |
REG_GPIO_DEBOUNCE
Name: PortA/B/C interrupt debounce register
Size: 32
Address offset: 048h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_DEBOUNCE_EN |
R/W |
0 |
Controls whether an external signal that is the source of an interrupt needs to be debounced to remove any spurious glitches. Writing a 1 to a bit in this register enables the debouncing circuitry. A signal must be valid for two periods of an external clock before it is internally Processed.
This register is available only if Portx is configured to generate interrupts (GPIO_PORTA_INTR = Include (1)) and when the debounce logic is included (GPIO_DEBOUNCE = Include (1)). |
REG_GPIO_INT_EOI
Name: PortA/B/C edge type interrupt clear register
Size: 32
Address offset: 04Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EOI |
R/W |
0 |
Controls the clearing of edge type interrupts from Portx. When a 1 is written into a corresponding bit of this register, the interrupt is cleared. All interrupts are cleared when Portx is not configured for interrupts.
|
REG_GPIO_EXT_PORT
Name: External PortA/B/C data register
Size: 32
Address offset: 050h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_EXT_PORTA |
R |
0 |
When Portx is configured as Input, then reading this location reads the values on the signal. When the data direction of Portx is set as Output, reading this location reads the data register for Portx. |
REG_GPIO_ITN_LS_SYNC
Name: PortA/B/C level interrupt synchronization
Size: 32
Address offset: 060h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
GPIO_LEVEL_SYNC |
R/W |
0 |
Writing a 1 to this register results in all level-sensitive interrupts being synchronized to pclk_intr.
|
REG_GPIO_ID_CODE
Name: PortA/B/C GPIO ID code register
Size: 32
Address offset: 064h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_ID_CODE |
R |
32'h1 |
This register is available only if Portx/B/C is configured to generate interrupts (GPIO_PORTx_INTR = Include (1)) and interrupt detection is configured to generate on both rising and falling edges of external input signal (GPIO_INT_BOTH_EDGE=Include (1)). |
REG_GPIO_INT_BOTHEDGE
Name: PortA/B/C both edge interrupt register
Size: 32
Address offset: 068h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_BOTHEDGE |
R/W |
0 |
Controls the edge types of interrupt that can occur on Portx. Whenever a particular bit is programmed to 1, it enables the generation of interrupt on both the rising edge and falling edge of an external input signal corresponding to that bit on PortA. The values programmed in the registers gpio_intype_level and gpio_int_polarity for this particular bit are not considered when the corresponding bit of this register is set to 1. Whenever a particular bit is programmed to 0, the interrupt type depends on the value of the corresponding bits in the gpio_inttype_level and gpio_int_polarity registers.
|
REG_GPIO_VER_ID_CODE
Name: PortA/B/C GPIO component version register
Size: 32
Address offset: 06Ch
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_VER_ID_CODE |
R |
32'h3231302A |
ASCII value for each number in the version, followed by *. For example 32_30_31_2A represents the version 2.01*. Reset Value: See the releases table in the Release Notes. |
REG_GPIO_DB_DIV_CONFIG
Size: 32
Address offset: 078h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:7 |
RSVD |
R |
- |
Reserved |
6:0 |
EXT_DB_DIV_CNT |
R/W |
0 |
Debounce interrupt prescaler of 32.768KHz. De-bounce time = (EXT_DB_DIV_CNT +1) * 2*32μs. |
Base Address: 0x40811000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
||
004h |
R/W |
||
008h |
R |
||
030h |
R/W |
||
034h |
R/W |
||
038h |
R/W |
||
03Ch |
R/W |
||
040h |
R |
||
044h |
R |
||
048h |
R/W |
||
04Ch |
R/W |
||
050h |
R |
||
060h |
R/W |
||
064h |
R |
||
068h |
R/W |
||
06Ch |
R |
||
078h |
R |
||
0FCh |
R |
REG_GPIO_DR
Name: Port data register
Size: 32
Address offset: 000h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORT_DATA |
R/W |
0 |
Values written to this register are output on the I/O signals for Portx if the corresponding data direction bits for Portx are set to Output mode and the corresponding control bit for Portx is set to software mode. The value read back is equal to the last value written to this register. |
REG_GPIO_DDR
Name: Port data direction register
Size: 32
Address offset: 004h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORT_DATA_DIRECTION |
R/W |
0 |
Values written to this register independently control the direction of the corresponding data bit in Portx. The default direction can be configured as input or output after system reset through the GPIO_DFLT_DIR_x parameter.
|
REG_GPIO_CTL
Name: Port data source register
Size: 32
Address offset: 008h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_GPIO_INT_EN
Name: Port interrupt enable register
Size: 32
Address offset: 030h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EN |
R/W |
0 |
Allows each bit of Portx to be configured for interrupts. By default, the generation of interrupts is disabled. Whenever a 1 is written to a bit of this register, it configures the corresponding bit on Portx to become an interrupt; otherwise, Portx operates as a normal GPIO signal. Interrupts are disabled on the corresponding bits of Portx if the corresponding data direction register is set to Output or if Portx mode is set to Hardware.
|
REG_GPIO_INT_MASK
Name: Port interrupt mask register
Size: 32
Address offset: 034h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_MASK |
R/W |
0 |
Controls whether an interrupt on Portx can create an interrupt for the interrupt controller by not masking it. By default, all interrupts bits are unmasked. Whenever a 1 is written to a bit in this register, it masks the interrupt generation capability for this signal; otherwise interrupts are allowed through. The unmasked status can be read as well as the resultant status after masking.
|
REG_GPIO_INT_TYPE
Name: Port interrupt trigger type register
Size: 32
Address offset: 038h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_TYPE |
R/W |
0 |
Controls the type of interrupt that can occur on Portx. Whenever a 0 is written to a bit of this register, it configures the Interrupt type to be level-sensitive; otherwise, it is edge-sensitive.
|
REG_GPIO_INT_POLARITY
Name: Port interrupt polarity register
Size: 32
Address offset: 03Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_POLARITY |
R/W |
0 |
Controls the polarity of edge or level sensitivity that can occur on input of Portx. Whenever a 0 is written to a bit of this register, it configures the interrupt type to falling-edge or active-low sensitive; otherwise, it is rising-edge or active-high sensitive.
|
REG_GPIO_INT_STATUS
Name: Port interrupt status register
Size: 32
Address offset: 040h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_STATUS |
R |
0 |
Interrupt status of Portx. |
REG_GPIO_INT_STATUS_RAW
Name: Port raw interrupt status register
Size: 32
Address offset: 044h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_RAW_INT_STATUS |
R |
0 |
Raw interrupt status of Portx (premasking bits). |
REG_GPIO_DEBOUNCE
Name: Port interrupt debounce register
Size: 32
Address offset: 048h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_DEBOUNCE_EN |
R/W |
0 |
Controls whether an external signal that is the source of an interrupt needs to be debounced to remove any spurious glitches. Writing a 1 to a bit in this register enables the debouncing circuitry. A signal must be valid for two periods of an external clock before it is internally Processed.
This register is available only if Portx is configured to generate interrupts (GPIO_PORTA_INTR = Include (1)) and when the debounce logic is included (GPIO_DEBOUNCE = Include (1)). |
REG_GPIO_INT_EOI
Name: Port edge type interrupt clear register
Size: 32
Address offset: 04Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EOI |
R/W |
0 |
Controls the clearing of edge type interrupts from Portx. When a 1 is written into a corresponding bit of this register, the interrupt is cleared. All interrupts are cleared when Portx is not configured for interrupts.
|
REG_GPIO_EXT_PORT
Name: External Port data register
Size: 32
Address offset: 050h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_EXT_PORTA |
R |
0 |
When Portx is configured as Input, then reading this location reads the values on the signal. When the data direction of Portx is set as Output, reading this location reads the data register for Portx. |
REG_GPIO_ITN_LS_SYNC
Name: Port level interrupt synchronization
Size: 32
Address offset: 060h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
GPIO_LEVEL_SYNC |
R/W |
0 |
Writing a 1 to this register results in all level-sensitive interrupts being synchronized to pclk_intr.
|
REG_GPIO_ID_CODE
Name: Port GPIO ID code register
Size: 32
Address offset: 064h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_ID_CODE |
R |
32'h1 |
This register is available only if Portx is configured to generate interrupts (GPIO_PORTx_INTR = Include (1)) and interrupt detection is configured to generate on both rising and falling edges of external input signal (GPIO_INT_BOTH_EDGE=Include (1)). |
REG_GPIO_INT_BOTHEDGE
Name: Port both edge interrupt register
Size: 32
Address offset: 068h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_BOTHEDGE |
R/W |
0 |
Controls the edge types of interrupt that can occur on Portx. Whenever a particular bit is programmed to 1, it enables the generation of interrupt on both the rising edge and falling edge of an external input signal corresponding to that bit on Port. The values programmed in the registers gpio_intype_level and gpio_int_polarity for this particular bit are not considered when the corresponding bit of this register is set to 1. Whenever a particular bit is programmed to 0, the interrupt type depends on the value of the corresponding bits in the gpio_inttype_level and gpio_int_polarity registers.
|
REG_GPIO_VER_ID_CODE
Name: Port GPIO component version register
Size: 32
Address offset: 06Ch
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_VER_ID_CODE |
R |
32'h3231302A |
ASCII value for each number in the version, followed by *. For example 32_30_31_2A represents the version 2.01*. Reset Value: See the releases table in the Release Notes. |
REG_GPIO_DB_DIV_CONFIG
Size: 32
Address offset: 078h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_GPIO_DUMMY
Size: 32
Address offset: 0FCh
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
DUMMY |
R |
0 |
No real reg, only for run_espec.py |
Base Address: 0x40802000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
||
004h |
R/W |
||
008h |
R |
||
030h |
R/W |
||
034h |
R/W |
||
038h |
R/W |
||
03Ch |
R/W |
||
040h |
R |
||
044h |
R |
||
048h |
R/W |
||
04Ch |
R/W |
||
050h |
R |
||
060h |
R/W |
||
064h |
R |
||
068h |
R/W |
||
06Ch |
R |
||
078h |
R |
||
0FCh |
R |
REG_GPIO_DR
Name: Port data register
Size: 32
Address offset: 000h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORT_DATA |
R/W |
0 |
Values written to this register are output on the I/O signals for Portx if the corresponding data direction bits for Portx are set to Output mode and the corresponding control bit for Portx is set to software mode. The value read back is equal to the last value written to this register. |
REG_GPIO_DDR
Name: Port data direction register
Size: 32
Address offset: 004h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
PORT_DATA_DIRECTION |
R/W |
0 |
Values written to this register independently control the direction of the corresponding data bit in Portx. The default direction can be configured as input or output after system reset through the GPIO_DFLT_DIR_x parameter.
|
REG_GPIO_CTL
Name: Port data source register
Size: 32
Address offset: 008h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_GPIO_INT_EN
Name: Port interrupt enable register
Size: 32
Address offset: 030h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EN |
R/W |
0 |
Allows each bit of Portx to be configured for interrupts. By default, the generation of interrupts is disabled. Whenever a 1 is written to a bit of this register, it configures the corresponding bit on Portx to become an interrupt; otherwise, Portx operates as a normal GPIO signal. Interrupts are disabled on the corresponding bits of Portx if the corresponding data direction register is set to Output or if Portx mode is set to Hardware.
|
REG_GPIO_INT_MASK
Name: Port interrupt mask register
Size: 32
Address offset: 034h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_MASK |
R/W |
0 |
Controls whether an interrupt on Portx can create an interrupt for the interrupt controller by not masking it. By default, all interrupts bits are unmasked. Whenever a 1 is written to a bit in this register, it masks the interrupt generation capability for this signal; otherwise interrupts are allowed through. The unmasked status can be read as well as the resultant status after masking.
|
REG_GPIO_INT_TYPE
Name: Port interrupt trigger type register
Size: 32
Address offset: 038h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_TYPE |
R/W |
0 |
Controls the type of interrupt that can occur on Portx. Whenever a 0 is written to a bit of this register, it configures the Interrupt type to be level-sensitive; otherwise, it is edge-sensitive.
|
REG_GPIO_INT_POLARITY
Name: Port interrupt polarity register
Size: 32
Address offset: 03Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_POLARITY |
R/W |
0 |
Controls the polarity of edge or level sensitivity that can occur on input of Portx. Whenever a 0 is written to a bit of this register, it configures the interrupt type to falling-edge or active-low sensitive; otherwise, it is rising-edge or active-high sensitive.
|
REG_GPIO_INT_STATUS
Name: Port interrupt status register
Size: 32
Address offset: 040h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_STATUS |
R |
0 |
Interrupt status of Portx. |
REG_GPIO_INT_STATUS_RAW
Name: Port raw interrupt status register
Size: 32
Address offset: 044h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_RAW_INT_STATUS |
R |
0 |
Raw interrupt status of Portx (premasking bits). |
REG_GPIO_DEBOUNCE
Name: Port interrupt debounce register
Size: 32
Address offset: 048h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_DEBOUNCE_EN |
R/W |
0 |
Controls whether an external signal that is the source of an interrupt needs to be debounced to remove any spurious glitches. Writing a 1 to a bit in this register enables the debouncing circuitry. A signal must be valid for two periods of an external clock before it is internally Processed.
This register is available only if Portx is configured to generate interrupts (GPIO_PORTA_INTR = Include (1)) and when the debounce logic is included (GPIO_DEBOUNCE = Include (1)). |
REG_GPIO_INT_EOI
Name: Port edge type interrupt clear register
Size: 32
Address offset: 04Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_EOI |
R/W |
0 |
Controls the clearing of edge type interrupts from Portx. When a 1 is written into a corresponding bit of this register, the interrupt is cleared. All interrupts are cleared when Portx is not configured for interrupts.
|
REG_GPIO_EXT_PORT
Name: External Port data register
Size: 32
Address offset: 050h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_EXT_PORTA |
R |
0 |
When Portx is configured as Input, then reading this location reads the values on the signal. When the data direction of Portx is set as Output, reading this location reads the data register for Portx. |
REG_GPIO_ITN_LS_SYNC
Name: Port level interrupt synchronization
Size: 32
Address offset: 060h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
GPIO_LEVEL_SYNC |
R/W |
0 |
Writing a 1 to this register results in all level-sensitive interrupts being synchronized to pclk_intr.
|
REG_GPIO_ID_CODE
Name: Port GPIO ID code register
Size: 32
Address offset: 064h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_ID_CODE |
R |
32'h1 |
This register is available only if Portx is configured to generate interrupts (GPIO_PORTx_INTR = Include (1)) and interrupt detection is configured to generate on both rising and falling edges of external input signal (GPIO_INT_BOTH_EDGE=Include (1)). |
REG_GPIO_INT_BOTHEDGE
Name: Port both edge interrupt register
Size: 32
Address offset: 068h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_INT_BOTHEDGE |
R/W |
0 |
Controls the edge types of interrupt that can occur on Portx. Whenever a particular bit is programmed to 1, it enables the generation of interrupt on both the rising edge and falling edge of an external input signal corresponding to that bit on Port. The values programmed in the registers gpio_intype_level and gpio_int_polarity for this particular bit are not considered when the corresponding bit of this register is set to 1. Whenever a particular bit is programmed to 0, the interrupt type depends on the value of the corresponding bits in the gpio_inttype_level and gpio_int_polarity registers.
|
REG_GPIO_VER_ID_CODE
Name: Port GPIO component version register
Size: 32
Address offset: 06Ch
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
GPIO_VER_ID_CODE |
R |
32'h3231302A |
ASCII value for each number in the version, followed by *. For example 32_30_31_2A represents the version 2.01*. Reset Value: See the releases table in the Release Notes. |
REG_GPIO_DB_DIV_CONFIG
Size: 32
Address offset: 078h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_GPIO_DUMMY
Size: 32
Address offset: 0FCh
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
DUMMY |
R |
0 |
No real reg, only for run_espec.py |
Base Address:
AON_GPIO : 0x40222000 (non-secure), 0x50222000 (secure)
SYSON_GPIO : 0x4020E000 (non-secure), 0x5020E000 (secure)
CORE_GPIO : 0x6020F000 (non-secure), 0x7020F000 (secure)
The three controllers share the same register layout.
Name |
Address offset |
Access |
|---|---|---|
000h |
R |
|
004h |
WO |
|
008h |
WO |
|
00Ch |
R |
|
014h |
WO |
|
018h |
WO |
|
01Ch |
WO |
|
020h |
R |
|
024h |
WO |
|
028h |
WO |
|
02Ch |
R |
|
030h |
R |
|
034h |
WO |
|
038h |
R |
|
03Ch |
WO |
|
040h |
WO |
|
050h |
R/W |
|
054h |
R/W |
|
058h |
R/W |
|
05Ch |
R/W |
|
060h |
R/W |
|
064h |
R/W |
|
068h |
R/W |
|
06Ch |
R/W |
|
070h |
R/W |
|
074h |
R/W |
|
078h |
R/W |
|
07Ch |
R/W |
|
080h |
R/W |
|
084h |
R/W |
|
088h |
R/W |
|
08Ch |
R/W |
|
0F0h |
R |
|
0F4h |
WO |
|
0F8h |
WO |
|
0FCh |
R |
|
100h |
R/W |
|
104h |
R/W |
|
108h |
R/W |
|
10Ch |
R/W |
|
110h |
R/W |
|
114h |
R/W |
|
118h |
R/W |
|
11Ch |
R/W |
|
120h |
R/W |
|
124h |
R/W |
|
128h |
R/W |
|
12Ch |
R/W |
|
130h |
R/W |
|
134h |
R/W |
|
138h |
R/W |
|
13Ch |
R/W |
|
200h |
R |
|
204h |
WO |
|
208h |
WO |
|
20Ch |
R |
|
210h |
WO |
|
214h |
WO |
|
218h |
WO |
|
21Ch |
R |
|
240h |
R |
|
244h |
WO |
|
248h |
WO |
|
24Ch |
R |
|
250h |
WO |
|
254h |
WO |
|
258h |
WO |
|
25Ch |
R |
REG_GPIO_IT_STS
Name: GPIO_IT_STS
Size: 32
Address offset: 000h
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
IT_STS |
R |
0: The specific GPIO port is configured to edge sensitive interrupt mode. 1: The specific GPIO port is configured to level sensitive interrupt mode. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_EI_EN
Name: GPIO_EI_EN
Size: 32
Address offset: 004h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
EI_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to edge sensitive interrupt mode and the specific bit of REG_GPIO_IT_STS is ZERO. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_LI_EN
Name: GPIO_LI_EN
Size: 32
Address offset: 008h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
LI_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to level sensitive interrupt mode and the specific bit of REG_GPIO_IT_STS is ONE. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_IP_STS
Name: GPIO_IP_STS
Size: 32
Address offset: 00Ch
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:30 |
GPIO15_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
29:28 |
GPIO14_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
27:26 |
GPIO13_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
25:24 |
GPIO12_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
23:22 |
GPIO11_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
21:20 |
GPIO10_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
19:18 |
GPIO9_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
17:16 |
GPIO8_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
15:14 |
GPIO7_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
13:12 |
GPIO6_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd This is RSVD (Reserved) for AON GPIO. |
11:10 |
GPIO5_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd |
9:8 |
GPIO4_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd |
7:6 |
GPIO3_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd |
5:4 |
GPIO2_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd |
3:2 |
GPIO1_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd |
1:0 |
GPIO0_IP_STS |
R |
00: The specific GPIO port is configured to rising-edge (active-high sensitive) 01: The specific GPIO port is configured to falling-edge (active-low sensitive) 10: The specific GPIO port is configured to dual-edge 11: rsvd |
REG_GPIO_IR_EN
Name: GPIO_IR_EN
Size: 32
Address offset: 014h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
IR_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to rising-edge interrupt mode and the specific bits of REG_GPIO_IP_STS is “00“. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_IF_EN
Name: GPIO_IF_EN
Size: 32
Address offset: 018h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
IF_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to falling-edge interrupt mode and the specific bits of REG_GPIO_IP_STS is “01“. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_ID_EN
Name: GPIO_ID_EN
Size: 32
Address offset: 01Ch
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
ID_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to dual-edge interrupt mode and the specific bits of REG_GPIO_IP_STS is “10“. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_IM_STS
Name: GPIO_IM_STS
Size: 32
Address offset: 020h
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
IM_STS |
R |
0: The interrupt mask of the specific GPIO port is disabled. 1: The interrupt mask of the specific GPIO port is enabled. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_IM_EN
Name: GPIO_IM_EN
Size: 32
Address offset: 024h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
IM_EN |
WO |
0: No operation. 1: The specific GPIO INT is unmasked and REG_GPIO_IM_STS is ONE. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_IM_DIS
Name: GPIO_IM_DIS
Size: 32
Address offset: 028h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
IM_DIS |
WO |
0: No operation. 1: The controlled GPIO INT is masked and the specific bit of REG_GPIO_IM_STS is ZERO. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_RAW_INT_STS
Name: GPIO_RAW_INT_STS
Size: 32
Address offset: 02Ch
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
RAW_INT_STS |
R |
0: The specific GPIO port has no interrupt request. 1: The specific GPIO port has interrupt request (permasking). Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_INT_STS
Name: GPIO_INT_STS
Size: 32
Address offset: 030h
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
INT_STS |
R |
0: The specific GPIO port has no interrupt request. 1: The specific GPIO port has interrupt request. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_INT_CLR
Name: GPIO_INT_CLR
Size: 32
Address offset: 034h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
INT_CLR |
WO |
0: No operation 1: Clear edge type interrupt request of the controlled GPIO port and the specific bits of REG_GPIOA_INT_STS is ZERO. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_INT_EN_STS
Name: GPIO_INT_EN_STS
Size: 32
Address offset: 038h
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
INT_EN_STS |
R |
0: The specific GPIO INT is disabled. 1: The specific GPIO INT is enabled. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_INT_EN
Name: GPIO_INT_EN
Size: 32
Address offset: 03Ch
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
INT_EN |
WO |
0: No operation. 1: The specific GPIO INT is enabled and the specific bit of REG_GPIO_INT_EN_STS is ONE. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_INT_DIS
Name: GPIO_INT_DIS
Size: 32
Address offset: 040h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
INT_DIS |
WO |
0: No operation. 1: The controlled GPIO INT is disabled and the specific bit of REG_GPIO_INT_EN_STS is ZERO. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_INT0_SEL
Name: GPIO_INT0_SEL
Size: 32
Address offset: 050h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT0_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT0_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT0. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT0_GP_SEL |
R/W |
GPIO port selection for GPIO INT0. There are 4 GPIO ports. |
4:0 |
INT0_MER_SEL |
R/W |
Member selection of specified group for GPIO INT0. Each member represents one GPIO pin. |
REG_GPIO_INT1_SEL
Name: GPIO_INT1_SEL
Size: 32
Address offset: 054h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT1_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT1_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT1. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT1_GP_SEL |
R/W |
GPIO port selection for GPIO INT1. There are 4 GPIO ports. |
4:0 |
INT1_MER_SEL |
R/W |
Member selection of specified group for GPIO INT1. Each member represents one GPIO pin. |
REG_GPIO_INT2_SEL
Name: GPIO_INT2_SEL
Size: 32
Address offset: 058h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT2_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT2_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT2. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT2_GP_SEL |
R/W |
GPIO port selection for GPIO INT2. There are 4 GPIO ports. |
4:0 |
INT2_MER_SEL |
R/W |
Member selection of specified group for GPIO INT2. Each member represents one GPIO pin. |
REG_GPIO_INT3_SEL
Name: GPIO_INT3_SEL
Size: 32
Address offset: 05Ch
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT3_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT3_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT3. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT3_GP_SEL |
R/W |
GPIO port selection for GPIO INT3. There are 4 GPIO ports. |
4:0 |
INT3_MER_SEL |
R/W |
Member selection of specified group for GPIO INT3. Each member represents one GPIO pin. |
REG_GPIO_INT4_SEL
Name: GPIO_INT4_SEL
Size: 32
Address offset: 060h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT4_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT4_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT4. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT4_GP_SEL |
R/W |
GPIO port selection for GPIO INT4. There are 4 GPIO ports. |
4:0 |
INT4_MER_SEL |
R/W |
Member selection of specified group for GPIO INT4. Each member represents one GPIO pin. |
REG_GPIO_INT5_SEL
Name: GPIO_INT5_SEL
Size: 32
Address offset: 064h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT5_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT5_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT5. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT5_GP_SEL |
R/W |
GPIO port selection for GPIO INT5. There are 4 GPIO ports. |
4:0 |
INT5_MER_SEL |
R/W |
Member selection of specified group for GPIO INT5. Each member represents one GPIO pin. |
REG_GPIO_INT6_SEL
Name: GPIO_INT6_SEL
Size: 32
Address offset: 068h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT6_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT6_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT6. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT6_GP_SEL |
R/W |
GPIO port selection for GPIO INT6. There are 4 GPIO ports. |
4:0 |
INT6_MER_SEL |
R/W |
Member selection of specified group for GPIO INT6. Each member represents one GPIO pin. |
REG_GPIO_INT7_SEL
Name: GPIO_INT7_SEL
Size: 32
Address offset: 06Ch
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT7_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT7_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT7 |
7 |
RSVD |
R |
Reserved |
6:5 |
INT7_GP_SEL |
R/W |
GPIO port selection for GPIO INT7. There are 4 GPIO ports. |
4:0 |
INT7_MER_SEL |
R/W |
Member selection of specified group for GPIO INT7. Each member represents one GPIO pin. |
REG_GPIO_INT8_SEL
Name: GPIO_INT8_SEL
Size: 32
Address offset: 070h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT8_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT8_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT8. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT8_GP_SEL |
R/W |
GPIO port selection for GPIO INT8. There are 4 GPIO ports. |
4:0 |
INT8_MER_SEL |
R/W |
Member selection of specified group for GPIO INT8. Each member represents one GPIO pin. |
REG_GPIO_INT9_SEL
Name: GPIO_INT9_SEL
Size: 32
Address offset: 074h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INT9_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INT9_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INT9. |
7 |
RSVD |
R |
Reserved |
6:5 |
INT9_GP_SEL |
R/W |
GPIO port selection for GPIO INT9. There are 4 GPIO ports. |
4:0 |
INT9_MER_SEL |
R/W |
Member selection of specified group for GPIO INT9. Each member represents one GPIO pin. |
REG_GPIO_INTA_SEL
Name: GPIO_INTA_SEL
Size: 32
Address offset: 078h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INTA_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INTA_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INTA. |
7 |
RSVD |
R |
Reserved |
6:5 |
INTA_GP_SEL |
R/W |
GPIO port selection for GPIO INTA. There are 4 GPIO ports. |
4:0 |
INTA_MER_SEL |
R/W |
Member selection of specified group for GPIO INTA. Each member represents one GPIO pin. |
REG_GPIO_INTB_SEL
Name: GPIO_INTB_SEL
Size: 32
Address offset: 07Ch
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INTB_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INTB_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INTB. |
7 |
RSVD |
R |
Reserved |
6:5 |
INTB_GP_SEL |
R/W |
GPIO port selection for GPIO INTB. There are 4 GPIO ports. |
4:0 |
INTB_MER_SEL |
R/W |
Member selection of specified group for GPIO INTB. Each member represents one GPIO pin. |
REG_GPIO_INTC_SEL
Name: GPIO_INTC_SEL
Size: 32
Address offset: 080h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INTC_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INTC_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INTC. |
7 |
RSVD |
R |
Reserved |
6:5 |
INTC_GP_SEL |
R/W |
GPIO port selection for GPIO INTC. There are 4 GPIO ports. |
4:0 |
INTC_MER_SEL |
R/W |
Member selection of specified group for GPIO INTC. Each member represents one GPIO pin. |
REG_GPIO_INTD_SEL
Name: GPIO_INTD_SEL
Size: 32
Address offset: 084h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INTD_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INTD_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INTD. |
7 |
RSVD |
R |
Reserved |
6:5 |
INTD_GP_SEL |
R/W |
GPIO port selection for GPIO INTD. There are 4 GPIO ports. |
4:0 |
INTD_MER_SEL |
R/W |
Member selection of specified group for GPIO INTD. Each member represents one GPIO pin. |
REG_GPIO_INTE_SEL
Name: GPIO_INTE_SEL
Size: 32
Address offset: 088h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INTE_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INTE_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INTE. |
7 |
RSVD |
R |
Reserved |
6:5 |
INTE_GP_SEL |
R/W |
GPIO port selection for GPIO INTE. There are 4 GPIO ports. |
4:0 |
INTE_MER_SEL |
R/W |
Member selection of specified group for GPIO INTE. Each member represents one GPIO pin. |
REG_GPIO_INTF_SEL
Name: GPIO_INTF_SEL
Size: 32
Address offset: 08Ch
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15 |
INTF_SUR_SEL |
R/W |
0: Using pin input signal as source. 1: Using debounce output signal as source. |
14:12 |
RSVD |
R |
Reserved |
11:8 |
INTF_DEB_SEL |
R/W |
Debounce Output signal selection for GPIO INTF. |
7 |
RSVD |
R |
Reserved |
6:5 |
INTF_GP_SEL |
R/W |
GPIO port selection for GPIO INTF. There are 4 GPIO ports. |
4:0 |
INTF_MER_SEL |
R/W |
Member selection of specified group for GPIO INTF. Each member represents one GPIO pin. |
REG_GPIO_DEB_STS
Name: GPIO_DEB_STS
Size: 32
Address offset: 0F0h
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
DEB_STS |
R |
0: The specific GPIO port has its debounce function disabled. 1: The specific GPIO port has its debounce function enabled. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_DEB_EN
Name: GPIO_DEB_EN
Size: 32
Address offset: 0F4h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
DEB_EN |
WO |
0: No operation. 1: The controlled GPIO debounce port has its debounce function enabled and the specific bit of REG_GPIO_DEB_STS is ONE. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_DEB_DIS
Name: GPIO_DEB_DIS
Size: 32
Address offset: 0F8h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
DEB_DIS |
WO |
0: No operation. 1: The controlled GPIO debounce port has its debounce function disabled and the specific bit of REG_GPIO_DEB_STS is ZERO. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_DEB_DP_STS
Name: GPIO_DEB_DP_STS
Size: 32
Address offset: 0FCh
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:16 |
RSVD |
R |
Reserved |
15:0 |
DEB_DP_STS |
R |
Reading this location reads the values of the signal on the specified pin after debounce. Each bit represents one GPIO pin. For AON GPIO, only Bit [5:0] are active, as there are only 6 AON GPIO pins. |
REG_GPIO_DEB0_SEL
Name: GPIO_DEB0_SEL
Size: 32
Address offset: 100h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB0_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB0_GP_SEL |
R/W |
GPIO port selection for debounce0. Supports up to 4 GPIO groups. |
4:0 |
DEB0_MER_SEL |
R/W |
Member selection of specified group for debounce0. Each member represents one GPIO pin. |
REG_GPIO_DEB1_SEL
Name: GPIO_DEB1_SEL
Size: 32
Address offset: 104h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB1_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB1_GP_SEL |
R/W |
GPIO port selection for debounce1. Supports up to 4 GPIO groups. |
4:0 |
DEB1_MER_SEL |
R/W |
Member selection of specified group for debounce1. Each member represents one GPIO pin. |
REG_GPIO_DEB2_SEL
Name: GPIO_DEB2_SEL
Size: 32
Address offset: 108h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB2_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB2_GP_SEL |
R/W |
GPIO port selection for debounce2. Supports up to 4 GPIO groups. |
4:0 |
DEB2_MER_SEL |
R/W |
Member selection of specified group for debounce2. Each member represents one GPIO pin. |
REG_GPIO_DEB3_SEL
Name: GPIO_DEB3_SEL
Size: 32
Address offset: 10Ch
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB3_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB3_GP_SEL |
R/W |
GPIO port selection for debounce3. Supports up to 4 GPIO groups. |
4:0 |
DEB3_MER_SEL |
R/W |
Member selection of specified group for debounce3. Each member represents one GPIO pin. |
REG_GPIO_DEB4_SEL
Name: GPIO_DEB4_SEL
Size: 32
Address offset: 110h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB4_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB4_GP_SEL |
R/W |
GPIO port selection for debounce4. Supports up to 4 GPIO groups. |
4:0 |
DEB4_MER_SEL |
R/W |
Member selection of specified group for debounce4. Each member represents one GPIO pin. |
REG_GPIO_DEB5_SEL
Name: GPIO_DEB5_SEL
Size: 32
Address offset: 114h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB5_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB5_GP_SEL |
R/W |
GPIO port selection for debounce5. Supports up to 4 GPIO groups. |
4:0 |
DEB5_MER_SEL |
R/W |
Member selection of specified group for debounce5. Each member represents one GPIO pin. |
REG_GPIO_DEB6_SEL
Name: GPIO_DEB6_SEL
Size: 32
Address offset: 118h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB6_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB6_GP_SEL |
R/W |
GPIO port selection for debounce6. Supports up to 4 GPIO groups. |
4:0 |
DEB6_MER_SEL |
R/W |
Member selection of specified group for debounce6. Each member represents one GPIO pin. |
REG_GPIO_DEB7_SEL
Name: GPIO_DEB7_SEL
Size: 32
Address offset: 11Ch
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB7_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB7_GP_SEL |
R/W |
GPIO port selection for debounce7. Supports up to 4 GPIO groups. |
4:0 |
DEB7_MER_SEL |
R/W |
Member selection of specified group for debounce7. Each member represents one GPIO pin. |
REG_GPIO_DEB8_SEL
Name: GPIO_DEB8_SEL
Size: 32
Address offset: 120h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB8_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB8_GP_SEL |
R/W |
GPIO port selection for debounce8. Supports up to 4 GPIO groups. |
4:0 |
DEB8_MER_SEL |
R/W |
Member selection of specified group for debounce8. Each member represents one GPIO pin. |
REG_GPIO_DEB9_SEL
Name: GPIO_DEB9_SEL
Size: 32
Address offset: 124h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEB9_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEB9_GP_SEL |
R/W |
GPIO port selection for debounce9. Supports up to 4 GPIO groups. |
4:0 |
DEB9_MER_SEL |
R/W |
Member selection of specified group for debounce9. Each member represents one GPIO pin. |
REG_GPIO_DEBA_SEL
Name: GPIO_DEBA_SEL
Size: 32
Address offset: 128h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEBA_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEBA_GP_SEL |
R/W |
GPIO port selection for debounceA. Supports up to 4 GPIO groups. |
4:0 |
DEBA_MER_SEL |
R/W |
Member selection of specified group for debounceA. Each member represents one GPIO pin. |
REG_GPIO_DEBB_SEL
Name: GPIO_DEBB_SEL
Size: 32
Address offset: 12Ch
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEBB_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEBB_GP_SEL |
R/W |
GPIO port selection for debounceB. Supports up to 4 GPIO groups. |
4:0 |
DEBB_MER_SEL |
R/W |
Member selection of specified group for debounceB. Each member represents one GPIO pin. |
REG_GPIO_DEBC_SEL
Name: GPIO_DEBC_SEL
Size: 32
Address offset: 130h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEBC_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEBC_GP_SEL |
R/W |
GPIO port selection for debounceC. Supports up to 4 GPIO groups. |
4:0 |
DEBC_MER_SEL |
R/W |
Member selection of specified group for debounceC. Each member represents one GPIO pin. |
REG_GPIO_DEBD_SEL
Name: GPIO_DEBD_SEL
Size: 32
Address offset: 134h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEBD_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEBD_GP_SEL |
R/W |
GPIO port selection for debounceD. Supports up to 4 GPIO groups. |
4:0 |
DEBD_MER_SEL |
R/W |
Member selection of specified group for debounceD. Each member represents one GPIO pin. |
REG_GPIO_DEBE_SEL
Name: GPIO_DEBE_SEL
Size: 32
Address offset: 138h
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEBE_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEBE_GP_SEL |
R/W |
GPIO port selection for debounceE. Supports up to 4 GPIO groups. |
4:0 |
DEBE_MER_SEL |
R/W |
Member selection of specified group for debounceE. Each member represents one GPIO pin. |
REG_GPIO_DEBF_SEL
Name: GPIO_DEBF_SEL
Size: 32
Address offset: 13Ch
Read/write access: R/W
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:22 |
RSVD |
R |
Reserved |
21:8 |
DEBF_CYC |
R/W |
The GPIO signal will be filtered by the number of debounce cycles of specified in this register. |
7 |
RSVD |
R |
Reserved |
6:5 |
DEBF_GP_SEL |
R/W |
GPIO port selection for debounceF. Supports up to 4 GPIO groups.. |
4:0 |
DEBF_MER_SEL |
R/W |
Member selection of specified group for debounceF. Each member represents one GPIO pin. |
REG_GPIOA_DMD_STS
Name: GPIOA_DMD_STS
Size: 32
Address offset: 200h
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOA_DMD_STS |
R |
0: The specific GPIO port is configured to INPUT data mode 1: The specific GPIO port is configured to OUTPUT data mode. Each bit represents one GPIO pin. |
REG_GPIOA_IDM_EN
Name: GPIOA_IDM_EN
Size: 32
Address offset: 204h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOA_IDM_EN |
WO |
0: The controlled GPIO port’s configuration is unchanged. 1: The controlled GPIO port is configured to input data mode and the specific bit of REG_GPIOA_DMD_STS is ZERO. Each bit represents one GPIO pin. |
REG_GPIOA_ODM_EN
Name: GPIOA_ODM_EN
Size: 32
Address offset: 208h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOA_ODM_EN |
WO |
0: The controlled GPIO port’s configuration is unchanged. 1: The controlled GPIO port is configured to output data mode and the specific bit of REG_GPIOA_DMD_STS is ONE. Each bit represents one GPIO pin. |
REG_GPIOA_OD_STS
Name: GPIOA_OD_STS
Size: 32
Address offset: 20Ch
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOA_OD_STS |
R |
0: The specific GPIO port is configured to output low. 1: The specific GPIO port is configured to output high, if the specific GPIO port is output data mode. Each bit represents one GPIO pin. |
REG_GPIOA_ODL_EN
Name: GPIOA_ODL_EN
Size: 32
Address offset: 210h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOA_ODL_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to output low and the specific bit of REG_GPIOA_OD_STS is ZERO. Each bit represents one GPIO pin. |
REG_GPIOA_ODH_EN
Name: GPIOA_ODH_EN
Size: 32
Address offset: 214h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOA_ODH_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to output high and the specific bit of REG_GPIOA_OD_STS is ONE. Each bit represents one GPIO pin. |
REG_GPIOA_ODT
Name: GPIOA_ODT
Size: 32
Address offset: 218h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOA_ODT |
R/W |
0: No operation. 1: Toggle output of the controlled GPIO port and the specific bit of REG_GPIOA_OD_STS is also toggled. Each bit represents one GPIO pin. |
REG_GPIOA_DP_STS
Name: GPIOA_DP_STS
Size: 32
Address offset: 21Ch
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOA_DP_STS |
R |
When the specific bit is configured as input mode, reading this register reads the values of the signals on the respective pins. When the direction of specific bit is configured as output, then reading this location reads the output data register for group A. However, if an external voltage is applied to the bit (pin) destined for output, the corresponding bit in REG_GPIOA_DP_STS will reflect the value of that external signal. Each bit represents one GPIO pin. |
REG_GPIOB_DMD_STS
Name: GPIOB_DMD_STS
Size: 32
Address offset: 240h
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOB_DMD_STS |
R |
0: The specific GPIO port is configured to INPUT data mode. 1: The specific GPIO port is configured to OUTPUT data mode. Each bit represents one GPIO pin. |
REG_GPIOB_IDM_EN
Name: GPIOB_IDM_EN
Size: 32
Address offset: 244h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOB_IDM_EN |
WO |
0: The controlled GPIO port’s configuration is unchanged. 1: The controlled GPIO port is configured to input data mode and the specific bit of REG_GPIOB_DMD_STS is ZERO. Each bit represents one GPIO pin. |
REG_GPIOB_ODM_EN
Name: GPIOB_ODM_EN
Size: 32
Address offset: 248h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOB_ODM_EN |
WO |
0: The controlled GPIO port’s configuration is unchanged. 1: The controlled GPIO port is configured to output data mode and the specific bit of REG_GPIOB_DMD_STS is ONE. Each bit represents one GPIO pin. |
REG_GPIOB_OD_STS
Name: GPIOB_OD_STS
Size: 32
Address offset: 24Ch
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOB_OD_STS |
R |
0: The specific GPIO port is configured to output low. 1: The specific GPIO port is configured to output high, if the specific GPIO port is output data mode. Each bit represents one GPIO pin. |
REG_GPIOB_ODL_EN
Name: GPIOB_ODL_EN
Size: 32
Address offset: 250h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOB_ODL_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to output low and the specific bit of REG_GPIOB_OD_STS is ZERO. Each bit represents one GPIO pin. |
REG_GPIOB_ODH_EN
Name: GPIOB_ODH_EN
Size: 32
Address offset: 254h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOB_ODH_EN |
WO |
0: No operation. 1: The controlled GPIO port is configured to output high and the specific bit of REG_GPIOB_OD_STS is ONE. Each bit represents one GPIO pin. |
REG_GPIOB_ODT
Name: GPIOB_ODT
Size: 32
Address offset: 258h
Read/write access: WO
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOB_ODT |
WO |
0: No operation. 1: Toggle output of the controlled GPIO port and the specific bit of REG_GPIOB_OD_STS is also toggled. Each bit represents one GPIO pin. |
REG_GPIOB_DP_STS
Name: GPIOB_DP_STS
Size: 32
Address offset: 25Ch
Read/write access: R
Bit |
Symbol |
Access |
Description |
|---|---|---|---|
31:0 |
GPIOB_DP_STS |
R |
When the specific bit is configured as input mode, then reading this register reads the values of the signal on the respective pins. When the direction of specific bit is configured as output, then reading this location reads the output data register for group B. However, if an external voltage is applied to the bit (pin) destined for output, the corresponding bit in REG_GPIOB_DP_STS will reflect the value of that external signal. Each bit represents one GPIO pin. |