寄存器
请查看
寄存器访问类型
,了解 Access 列缩写的含义。
本节介绍 DMAC 的可编程寄存器。所有寄存器都按 64 位边界对齐,并且为 64 位宽。通常,寄存器的高 32 位被保留。如果没有特殊说明,对寄存器内保留位的写入将被忽略。
备注
本章中引用了软件参数和硬件参数。
软件参数是每个寄存器描述表中的字段名称,并以寄存器名称为前缀;例如,通道 x 的控制寄存器中的块传输大小字段被指定为
CTL_Hx.BLOCK_TS。硬件参数以 DMAC_* 为前缀,并使用 Realtek coreTools 配置一次。
随 RTK_DMAC 组件一起提供的是一个地址定义(内存映射)C 头文件。当在 C 环境中编程 DMAC 时,可以使用此头文件。
Base Address: 0x40110000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
004h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
008h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
00Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
010h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
018h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
01Ch |
R |
Control register high for DMA channel x for block size |
|
040h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
044h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
058h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
05Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
060h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
064h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
068h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
070h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
074h |
R |
Control register high for DMA channel x for block size |
|
098h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
09Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
0B0h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
0B4h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
0B8h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
0BCh |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
0C0h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
0C8h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
0CCh |
R |
Control register high for DMA channel x for block size |
|
0F0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
0F4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
108h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
10Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
110h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
114h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
118h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
120h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
124h |
R |
Control register high for DMA channel x for block size |
|
148h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
14Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
160h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
164h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
168h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
16Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
170h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
178h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
17Ch |
R |
Control register high for DMA channel x for block size |
|
1A0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1A4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
1B8h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
1BCh |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
1C0h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
1C4h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
1C8h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
1D0h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
1D4h |
R |
Control register high for DMA channel x for block size |
|
1F8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1FCh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
210h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
214h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
218h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
21Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
220h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
228h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
22Ch |
R |
Control register high for DMA channel x for block size |
|
250h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
254h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
268h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
26Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
270h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
274h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
278h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
280h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
284h |
R |
Control register high for DMA channel x for block size |
|
2A8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
2ACh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
2C0h |
R |
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts |
|
2C8h |
R |
Raw block transfer complete interrupt status register, shows unmasked block transfer complete interrupts |
|
2E0h |
R |
Raw error interrupt status register low, shows unmasked protocol error interrupts |
|
2E4h |
R |
Raw error interrupt status register high, shows unmasked secure error interrupts |
|
2E8h |
R |
Transfer complete interrupt status register, shows masked transfer complete interrupts |
|
2F0h |
R |
Block transfer complete interrupt status register, shows masked block transfer complete interrupts |
|
308h |
R |
Error interrupt status register low, shows masked protocol error interrupts |
|
30Ch |
R |
Error interrupt status register high, shows masked secure error interrupts |
|
310h |
R/W |
Transfer complete interrupt mask register, enables or disables transfer complete interrupts |
|
318h |
R/W |
Block transfer complete interrupt mask register, enables or disables block transfer complete interrupts |
|
330h |
R/W |
Error interrupt mask register low, enables or disables protocol error interrupts |
|
334h |
R/W |
Error interrupt mask register high, enables or disables secure error interrupts |
|
338h |
R/W |
Transfer complete interrupt clear register, clears transfer complete interrupt status |
|
340h |
R/W |
Block transfer complete interrupt clear register, clears block transfer complete interrupt status |
|
358h |
R/W |
Error interrupt clear register low, clears protocol error interrupt status |
|
35Ch |
R/W |
Error interrupt clear register high, clears secure error interrupt status |
|
360h |
R |
Interrupt status register low, shows combined interrupt status |
|
364h |
R |
Interrupt status register high, shows combined interrupt status |
|
398h |
R/W |
DMA configuration register, configures global DMA controller settings |
|
3A0h |
R/W |
Channel enable register, enables or disables DMA channels |
|
3A8h |
R |
DMA ID register, Hardcoded RTK_DMAC peripheral ID |
|
3C8h |
R |
DMA component parameters register 6 low, contains component identification information |
|
3CCh |
R |
DMA component parameters register 6 high, contains component identification information |
|
3D0h |
R |
DMA component parameters register 5 low, contains component identification information |
|
3D4h |
R |
DMA component parameters register 5 high, contains component identification information |
|
3D8h |
R |
DMA component parameters register 4 low, contains component identification information |
|
3DCh |
R |
DMA component parameters register 4 high, contains component identification information |
|
3E0h |
R |
DMA component parameters register 3 low, contains component identification information |
|
3E4h |
R |
DMA component parameters register 3 high, contains component identification information |
|
3E8h |
R |
DMA component parameters register 2 low, contains component identification information |
|
3ECh |
R |
DMA component parameters register 2 high, contains component identification information |
|
3F0h |
R |
DMA component parameters register 1 low, contains component identification information |
|
3F4h |
R |
DMA component parameters register 1 high, contains component identification information |
|
3F8h |
R |
DMA component ID register low, identifies the DMA controller release date |
|
3FCh |
R |
DMA component ID register high, identifies the DMA controller rtl version |
REG_SAR0
Name: Channel 0 Source Address Register
Size: 32
Address offset: 000h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR0 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR0
Name: The read back value is channel 0 source reading address at present
Size: 32
Address offset: 004h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR0 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR0
Name: Channel 0 Destination Address Register
Size: 32
Address offset: 008h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR0 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR0
Name: The read back value is channel 0 destination writing address at present
Size: 32
Address offset: 00Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR0 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP0_L
Name: Channel 0 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 010h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP0_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL0_L
Name: Channel 0 low-32 bits Control Register
Size: 32
Address offset: 018h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL0_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL0_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL0_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL0_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL0_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL0_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL0_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL0_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL0_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL0_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL0_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL0_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL0_H
Name: Channel 0 high-32 bits Control Register
Size: 32
Address offset: 01Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL0_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG0_L
Name: Channel 0 low-32 bits Configuration Register
Size: 32
Address offset: 040h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG0_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG0_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG0_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG0_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG0_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG0_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG0_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG0_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG0_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG0_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG0_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG0_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG0_H
Name: Channel 0 high-32 bits Configuration Register
Size: 32
Address offset: 044h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG0_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG0_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG0_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG0_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG0_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG0_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR1
Name: Channel 1 Source Address Register
Size: 32
Address offset: 058h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR1 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR1
Name: The read back value is channel 1 source reading address at present
Size: 32
Address offset: 05Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR1 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR1
Name: Channel 1 Destination Address Register
Size: 32
Address offset: 060h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR1 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR1
Name: The read back value is channel 1 destination writing address at present
Size: 32
Address offset: 064h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR1 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP1_L
Name: Channel 1 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 068h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP1_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL1_L
Name: Channel 1 low-32 bits Control Register
Size: 32
Address offset: 070h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL1_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL1_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL1_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL1_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL1_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL1_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL1_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL1_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL1_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL1_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL1_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL1_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL1_H
Name: Channel 1 high-32 bits Control Register
Size: 32
Address offset: 074h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL1_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG1_L
Name: Channel 1 low-32 bits Configuration Register
Size: 32
Address offset: 098h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG1_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG1_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG1_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG1_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG1_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG1_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG1_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG1_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG1_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG1_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG1_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG1_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG1_H
Name: Channel 1 high-32 bits Configuration Register
Size: 32
Address offset: 09Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG1_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG1_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG1_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG1_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG1_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG1_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR2
Name: Channel 2 Source Address Register
Size: 32
Address offset: 0B0h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR2 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR2
Name: The read back value is channel 2 source reading address at present
Size: 32
Address offset: 0B4h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR2 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR2
Name: Channel 2 Destination Address Register
Size: 32
Address offset: 0B8h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR2 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR2
Name: The read back value is channel 2 destination writing address at present
Size: 32
Address offset: 0BCh
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR2 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP2_L
Name: Channel 2 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 0C0h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP2_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL2_L
Name: Channel 2 low-32 bits Control Register
Size: 32
Address offset: 0C8h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL2_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL2_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL2_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL2_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL2_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL2_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL2_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL2_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL2_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL2_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL2_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL2_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL2_H
Name: Channel 2 high-32 bits Control Register
Size: 32
Address offset: 0CCh
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL2_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG2_L
Name: Channel 2 low-32 bits Configuration Register
Size: 32
Address offset: 0F0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG2_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG2_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG2_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG2_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG2_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG2_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG2_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG2_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG2_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG2_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG2_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG2_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG2_H
Name: Channel 2 high-32 bits Configuration Register
Size: 32
Address offset: 0F4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG2_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG2_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG2_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG2_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG2_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG2_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR3
Name: Channel 3 Source Address Register
Size: 32
Address offset: 108h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR3 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR3
Name: The read back value is channel 3 source reading address at present
Size: 32
Address offset: 10Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR3 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR3
Name: Channel 3 Destination Address Register
Size: 32
Address offset: 110h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR3 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR3
Name: The read back value is channel 3 destination writing address at present
Size: 32
Address offset: 114h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR3 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP3_L
Name: Channel 3 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 118h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP3_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL3_L
Name: Channel 3 low-32 bits Control Register
Size: 32
Address offset: 120h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL3_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL3_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL3_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL3_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL3_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL3_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL3_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL3_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL3_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL3_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL3_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL3_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL3_H
Name: Channel 3 high-32 bits Control Register
Size: 32
Address offset: 124h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL3_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG3_L
Name: Channel 3 low-32 bits Configuration Register
Size: 32
Address offset: 148h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG3_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG3_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG3_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG3_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG3_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG3_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG3_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG3_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG3_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG3_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG3_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG3_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG3_H
Name: Channel 3 high-32 bits Configuration Register
Size: 32
Address offset: 14Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG3_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG3_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG3_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG3_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG3_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG3_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR4
Name: Channel 4 Source Address Register
Size: 32
Address offset: 160h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR4 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR4
Name: The read back value is channel 4 source reading address at present
Size: 32
Address offset: 164h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR4 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR4
Name: Channel 4 Destination Address Register
Size: 32
Address offset: 168h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR4 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR4
Name: The read back value is channel 4 destination writing address at present
Size: 32
Address offset: 16Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR4 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP4_L
Name: Channel 4 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 170h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP4_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL4_L
Name: Channel 4 low-32 bits Control Register
Size: 32
Address offset: 178h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL4_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL4_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL4_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL4_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL4_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL4_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL4_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL4_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL4_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL4_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL4_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL4_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL4_H
Name: Channel 4 high-32 bits Control Register
Size: 32
Address offset: 17Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL4_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG4_L
Name: Channel 4 low-32 bits Configuration Register
Size: 32
Address offset: 1A0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG4_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG4_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG4_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG4_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG4_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG4_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG4_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG4_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG4_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG4_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG4_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG4_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG4_H
Name: Channel 4 high-32 bits Configuration Register
Size: 32
Address offset: 1A4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG4_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG4_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG4_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG4_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG4_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG4_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR5
Name: Channel 5 Source Address Register
Size: 32
Address offset: 1B8h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR5 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR5
Name: The read back value is channel 5 source reading address at present
Size: 32
Address offset: 1BCh
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR5 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR5
Name: Channel 5 Destination Address Register
Size: 32
Address offset: 1C0h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR5 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR5
Name: The read back value is channel 5 destination writing address at present
Size: 32
Address offset: 1C4h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR5 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP5_L
Name: Channel 5 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 1C8h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP5_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL5_L
Name: Channel 5 low-32 bits Control Register
Size: 32
Address offset: 1D0h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL5_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL5_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL5_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL5_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL5_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL5_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL5_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL5_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL5_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL5_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL5_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL5_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL5_H
Name: Channel 5 high-32 bits Control Register
Size: 32
Address offset: 1D4h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL5_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG5_L
Name: Channel 5 low-32 bits Configuration Register
Size: 32
Address offset: 1F8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG5_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG5_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG5_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG5_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG5_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG5_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG5_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG5_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG5_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG5_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG5_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG5_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG5_H
Name: Channel 5 high-32 bits Configuration Register
Size: 32
Address offset: 1FCh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG5_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG5_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG5_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG5_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG5_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG5_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR6
Name: Channel 6 Source Address Register
Size: 32
Address offset: 210h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR6 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR6
Name: The read back value is channel 6 source reading address at present
Size: 32
Address offset: 214h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR6 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR6
Name: Channel 6 Destination Address Register
Size: 32
Address offset: 218h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR6 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR6
Name: The read back value is channel 6 destination writing address at present
Size: 32
Address offset: 21Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR6 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP6_L
Name: Channel 6 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 220h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP6_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL6_L
Name: Channel 6 low-32 bits Control Register
Size: 32
Address offset: 228h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL6_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL6_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL6_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL6_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL6_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL6_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL6_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL6_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL6_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL6_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL6_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL6_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL6_H
Name: Channel 6 high-32 bits Control Register
Size: 32
Address offset: 22Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL6_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG6_L
Name: Channel 6 low-32 bits Configuration Register
Size: 32
Address offset: 250h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG6_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG6_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG6_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG6_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG6_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG6_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG6_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG6_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG6_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG6_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG6_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG6_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG6_H
Name: Channel 6 high-32 bits Configuration Register
Size: 32
Address offset: 254h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG6_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG6_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG6_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG6_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG6_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG6_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR7
Name: Channel 7 Source Address Register
Size: 32
Address offset: 268h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR7 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR7
Name: The read back value is channel 7 source reading address at present
Size: 32
Address offset: 26Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR7 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR7
Name: Channel 7 Destination Address Register
Size: 32
Address offset: 270h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR7 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR7
Name: The read back value is channel 7 destination writing address at present
Size: 32
Address offset: 274h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR7 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP7_L
Name: Channel 7 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 278h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP7_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL7_L
Name: Channel 7 low-32 bits Control Register
Size: 32
Address offset: 280h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL7_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL7_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL7_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL7_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL7_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL7_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL7_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL7_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL7_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL7_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL7_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL7_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL7_H
Name: Channel 7 high-32 bits Control Register
Size: 32
Address offset: 284h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL7_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG7_L
Name: Channel 7 low-32 bits Configuration Register
Size: 32
Address offset: 2A8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG7_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG7_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG7_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG7_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG7_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG7_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG7_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG7_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG7_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG7_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG7_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG7_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG7_H
Name: Channel 7 high-32 bits Configuration Register
Size: 32
Address offset: 2ACh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG7_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG7_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG7_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG7_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG7_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG7_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_RAWTFR_L
Name: Raw Status for IntTfr Interrupt
Size: 32
Address offset: 2C0h
Read/write access: R
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWTFR_L_RAW_TFR |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWBLOCK_L
Name: Raw Status for IntBlock Interrupt
Size: 32
Address offset: 2C8h
Read/write access: R
Raw block transfer complete interrupt status register, shows unmasked block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWBLOCK_L_RAW_BLOCK |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWERR_L
Name: Raw Status for IntErr Interrupt(protocol error)
Size: 32
Address offset: 2E0h
Read/write access: R
Raw error interrupt status register low, shows unmasked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_L_RAW_ERR |
R |
0x0 |
Raw interrupt status for chn0-chn15. (Protocol error) |
REG_RAWERR_H
Name: Raw Status for non-secure access secure register error if defined
Size: 32
Address offset: 2E4h
Read/write access: R
Raw error interrupt status register high, shows unmasked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_H_RAW_ERR |
R |
0x0 |
Raw interrupt status. (Non-secure access secure register error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_STATUSTFR_L
Name: Status for IntTfr Interrupt
Size: 32
Address offset: 2E8h
Read/write access: R
Transfer complete interrupt status register, shows masked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSTFR_L_STATUS_TFR |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSBLOCK_L
Name: Status for IntBlock Interrupt
Size: 32
Address offset: 2F0h
Read/write access: R
Block transfer complete interrupt status register, shows masked block transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSBLOCK_L_STATUS_BLOCK |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSERR_L
Name: Status for IntErr Interrupt
Size: 32
Address offset: 308h
Read/write access: R
Error interrupt status register low, shows masked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_L_STATUS_ERR |
R |
0x0 |
Interrupt status for chn0-chn15. (Protocol error) |
REG_STATUSERR_H
Name: Status for non-secure access secure register error if defined
Size: 32
Address offset: 30Ch
Read/write access: R
Error interrupt status register high, shows masked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_H_STATUS_ERR |
R |
0x0 |
Interrupt status. (Non-secure access secure register error, Sec Error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_MASKTFR_L
Name: Mask for IntTfr Interrupt (chn0-7)
Size: 32
Address offset: 310h
Read/write access: R/W
Transfer complete interrupt mask register, enables or disables transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKTFR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKTFR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKBLOCK_L
Name: Mask for IntBlock Interrupt
Size: 32
Address offset: 318h
Read/write access: R/W
Block transfer complete interrupt mask register, enables or disables block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKBLOCK_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKBLOCK_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_L
Name: Mask for IntErr Interrupt
Size: 32
Address offset: 330h
Read/write access: R/W
Error interrupt mask register low, enables or disables protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKERR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_H
Name: Mask for non-secure access secure register error if defined
Size: 32
Address offset: 334h
Read/write access: R/W
Error interrupt mask register high, enables or disables secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_H_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled These bits only exist when DMAC_ SECURE_MODE has beed defined |
7:0 |
MASKERR_H_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked These bits only exist when DMAC_ SECURE_MODE has beed defined |
REG_CLEARTFR_L
Name: Clear for IntTfr Interrupt
Size: 32
Address offset: 338h
Read/write access: R/W
Transfer complete interrupt clear register, clears transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARTFR_L_CLEAR_TFR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 0 = no effect 1= clear interrupt |
REG_CLEARBLOCK_L
Name: Clear for IntBlock Interrupt
Size: 32
Address offset: 340h
Read/write access: R/W
Block transfer complete interrupt clear register, clears block transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARBLOCK_L_CLEAR_BLOCK |
R/W |
0x0 |
Interrupt clear for chn0-chn15 |
REG_CLEARERR_L
Name: Clear for IntErr Interrupt
Size: 32
Address offset: 358h
Read/write access: R/W
Error interrupt clear register low, clears protocol error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_L_CLEAR_PROTOCOL_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15. (Protocol error) |
REG_CLEARERR_H
Name: Clear for non-secure access secure register error if defined
Size: 32
Address offset: 35Ch
Read/write access: R/W
Error interrupt clear register high, clears secure error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_H_CLEAR_SEC_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 (Non-secure access secure register error, Sec Error) when DMAC_SECURE_MODE has beed defined, else it is reserved; |
REG_STATUSINT_L
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 360h
Read/write access: R
Interrupt status register low, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
STATUSINT_L_ERROR |
R |
0x0 |
OR of the contents of StatusErr register. |
3:2 |
RSVD |
R |
- |
Reserved |
1 |
STATUSINT_L_BLOCK |
R |
0x0 |
OR of the contents of StatusBlock register. |
0 |
STATUSINT_L_TFR |
R |
0x0 |
OR of the contents of StatusTfr register. |
REG_STATUSINT_H
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 364h
Read/write access: R
Interrupt status register high, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_DMACFGREG_L
Name: DMA low-32 bits Configuration Register
Size: 32
Address offset: 398h
Read/write access: R/W
DMA configuration register, configures global DMA controller settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
DMACFGREG_L_DMA_EN |
R/W |
0x1 |
RTK_DMAC Enable bit. 0 = RTK_DMAC Disabled 1 = RTK_DMAC Enabled |
REG_CHENREG_L_1
Name: DMA low-32 bits Channel Enable Register if configed chn number is less than or equal to 8
Size: 32
Address offset: 3A0h
Read/write access: R/W
Channel enable register, enables or disables DMA channels
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
CHENREG_L_1_CH_EN_WE |
R/W |
0x0 |
Channel enable write enable. |
7:0 |
CHENREG_L_1_CH_EN |
R/W |
0x0 |
Enables/Disables the channel. Setting this bit enables a channel; clearing this bit disables the channel. 0 = Disable the Channel 1 = Enable the Channel The CHENREG_L.CH_EN bit is automatically cleared by hardware to disable the channel after the last AXI transfer of the DMA transfer to the destination has completed. Software can therefore poll this bit to determine when this channel is free for a new DMA transfer. |
REG_DMAIDREG_L
Name: DMA low-32 bits ID Register
Size: 32
Address offset: 3A8h
Read/write access: R
DMA ID register, Hardcoded RTK_DMAC peripheral ID
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMAIDREG_L_DMA_ID |
R |
32'h22101416 |
Hardcoded RTK_DMAC Peripheral ID |
REG_DMA_COMP_PARAMS_6_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3C8h
Read/write access: R
DMA component parameters register 6 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH7_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH7_MAX_BLK_SIZE from config_form.vh CH7_MAX_BLK_SIZE = log2(DMAC_CH7_MAX_BLK_SIZE) + 1 |
23:16 |
CH6_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH6_MAX_BLK_SIZE from config_form.vh CH6_MAX_BLK_SIZE = log2(DMAC_CH6_MAX_BLK_SIZE) + 1 |
15:8 |
CH5_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH5_MAX_BLK_SIZE from config_form.vh CH5_MAX_BLK_SIZE = log2(DMAC_CH5_MAX_BLK_SIZE) + 1 |
7:0 |
CH4_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH4_MAX_BLK_SIZE from config_form.vh CH4_MAX_BLK_SIZE = log2(DMAC_CH4_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_6_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3CCh
Read/write access: R
DMA component parameters register 6 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH7_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH7_FIFO_DEPTH parameter. Default value is 0x0. CH7_FIFO_DEPTH = log2(DMAC_CH7_FIFO_DEPTH/8) 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH7_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_MULT_SIZE parameter. Maxium burst transaction size. CH7_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH7_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH7_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH7_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH7_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH7_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH7_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH7_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH7_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH7_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH7_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH7_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D0h
Read/write access: R
DMA component parameters register 5 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH6_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH6_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH6_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_MULT_SIZE parameter. Maxium burst transaction size. CH6_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH6_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH6_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH6_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH6_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH6_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH6_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH6_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH6_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH6_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH6_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH6_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH6_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D4h
Read/write access: R
DMA component parameters register 5 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH5_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH5_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH5_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_MULT_SIZE parameter. Maxium burst transaction size. CH5_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH5_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH5_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH5_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH5_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH5_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH5_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH5_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH5_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH5_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH5_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH5_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH5_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D8h
Read/write access: R
DMA component parameters register 4 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH4_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH4_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH4_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_MULT_SIZE parameter. Maxium burst transaction size. CH4_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH4_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH4_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH4_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH4_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH4_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH4_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH4_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112.0x0 = FALSE 0x1 = TRUE |
8 |
CH4_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH4_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH4_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH4_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH4_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3DCh
Read/write access: R
DMA component parameters register 4 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH3_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH3_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH3_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_MULT_SIZE parameter. Maxium burst transaction size. CH3_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH3_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH3_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH3_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH3_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH3_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH3_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH3_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH3_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH3_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH3_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH3_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E0h
Read/write access: R
DMA component parameters register 3 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH2_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH2_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH2_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_MULT_SIZE parameter. Maxium burst transaction size. CH2_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH2_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH2_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH2_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH2_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH2_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH2_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH2_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH2_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH2_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH2_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH2_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E4h
Read/write access: R
DMA component parameters register 3 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH1_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH1_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH1_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_MULT_SIZE parameter. Maxium burst transaction size. CH1_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH1_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH1_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH1_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH1_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH1_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH1_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH1_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH1_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH1_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH1_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH1_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E8h
Read/write access: R
DMA component parameters register 2 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH0_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH0_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH0_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_MULT_SIZE parameter. Maxium burst transaction size. CH0_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH0_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH0_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH0_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH0_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH0_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH0_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH0_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH0_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH0_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH0_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH0_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3ECh
Read/write access: R
DMA component parameters register 2 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:28 |
CH7_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
27:24 |
CH6_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
23:20 |
CH5_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
19:16 |
CH4_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
15:12 |
CH3_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
11:8 |
CH2_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
7:4 |
CH1_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
3:0 |
CH0_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
REG_DMA_COMP_PARAMS_1_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F0h
Read/write access: R
DMA component parameters register 1 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH3_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH3_MAX_BLK_SIZE from config_form.vh CH3_MAX_BLK_SIZE = log2(DMAC_CH3_MAX_BLK_SIZE) + 1 |
23:16 |
CH2_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH2_MAX_BLK_SIZE from config_form.vh CH2_MAX_BLK_SIZE = log2(DMAC_CH2_MAX_BLK_SIZE) + 1 |
15:8 |
CH1_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH1_MAX_BLK_SIZE from config_form.vh CH1_MAX_BLK_SIZE = log2(DMAC_CH1_MAX_BLK_SIZE) + 1 |
7:0 |
CH0_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH0_MAX_BLK_SIZE from config_form.vh CH0_MAX_BLK_SIZE = log2(DMAC_CH0_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_1_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F4h
Read/write access: R
DMA component parameters register 1 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
HIGH_BIT_NUM_HS_INT3 |
R |
0x0 |
Number of hardware handshake interfaces. If it is 128, this bit read value is 1. |
30 |
HIGH_BIT_NUM_HS_INT2 |
R |
0x0 |
Number of hardware handshake interfaces. If it is greater than 63 and less than 128, this bit read value is 1. |
29 |
HIGH_BIT_NUM_HS_INT1 |
R |
0x0 |
Number of hardware handshake interfaces. If it is greater than 31 and less than 64, this bit read value is 1. |
28 |
STATIC_ENDIAN_SELECT |
R |
0 |
The value of this register is derived from the DMAC_STATIC_ENDIAN_SELECT parameter. 0 = FALSE (dynamic endian fixed) 1 = TRUE (not supported) |
27 |
ADD_ENCODED_PARAMS |
R |
1 |
The value of this register is derived from the DMAC_ADD_ENCODED_PARAMS parameter. 0 = FALSE 1 = TRUE |
26:22 |
NUM_HS_INT |
R |
0x1E |
Number of hardware handshake interfaces. The value of this register is derived from the DMAC_NUM_HS_INT parameter. NUM_HAS_INT = DMAC_NUM_HS_INT[4:0] 0x00 = 0 … 0x10 = 16 |
21:18 |
RSVD |
R |
- |
Reserved |
17:16 |
M2_DATA_WIDTH |
R |
0x0 |
AXI Master2 data width. The value of this register is derived from the DMAC_M2_DATA_WIDTH parameter. Master2 data width should be equal to that of Master 1. M2_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
15:14 |
M1_DATA_WIDTH |
R |
0x0 |
AXI Master1 data width. The value of this register is derived from the DMAC_M1_DATA_WIDTH parameter. Master1 data width should be equal to that of Master 2. M1_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
13:12 |
S_DATA_WIDTH |
R |
0x0 |
APB slave interface data width.The value of this register is derived from the DMAC_S_DATA_WIDTH parameter. The width is fixed to 32 bits for now. S_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = Reserved 0x2 = Reserved 0x3 = Reserved |
11:10 |
NUM_MASTER_INT |
R |
0x1 |
Number of master interface. The value of this register is derived from the DMAC_NUM_MASTER_INT parameter. This value is fixed to 1 (only 2 AXI masters supported now.) 0x0 = Reserved 0x1 = 2 0x2 = Reserved 0x3 = Reserved |
9:6 |
NUM_CHANNELS |
R |
0x7 |
Number of channels. The value of this register is derived from the DMAC_NUM_CHASNNELS parameter. NUM_CHANNELS = DMAC_NUM_CHASNNELS -1 0x0 = 1 … 0xf = 16 |
5:2 |
RSVD |
R |
- |
Reserved |
1:0 |
INTR_IO |
R |
0x0 |
Interrupt output format.The value of this register is derived from the DMAC_INTR_IO parameter. 0x0 = ALL 0x1 = TYPE 0x2 = COMBINED 0x3 = reserved |
REG_DMA_COMPONENT_ID_REGS_L
Name: DMAC ID
Size: 32
Address offset: 3F8h
Read/write access: R
DMA component ID register low, identifies the DMA controller release date
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMA_COMPONENT_ID |
R |
32'h22101416 |
DMAC ID (release_date_. Configure it in config form. |
REG_DMA_COMPONENT_ID_REGS_H
Name: It is obtained from the high 32 bits from git logs in git server.
Size: 32
Address offset: 3FCh
Read/write access: R
DMA component ID register high, identifies the DMA controller rtl version
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RTL_GIT_VER |
R |
32'h00201028 |
It is obtained from the high 32 bits from git logs in git server. |
Base Address: 0x40110000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
004h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
008h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
00Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
010h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
018h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
01Ch |
R |
Control register high for DMA channel x for block size |
|
040h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
044h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
058h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
05Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
060h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
064h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
068h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
070h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
074h |
R |
Control register high for DMA channel x for block size |
|
098h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
09Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
0B0h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
0B4h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
0B8h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
0BCh |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
0C0h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
0C8h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
0CCh |
R |
Control register high for DMA channel x for block size |
|
0F0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
0F4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
108h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
10Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
110h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
114h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
118h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
120h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
124h |
R |
Control register high for DMA channel x for block size |
|
148h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
14Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
160h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
164h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
168h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
16Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
170h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
178h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
17Ch |
R |
Control register high for DMA channel x for block size |
|
1A0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1A4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
1B8h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
1BCh |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
1C0h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
1C4h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
1C8h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
1D0h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
1D4h |
R |
Control register high for DMA channel x for block size |
|
1F8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1FCh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
210h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
214h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
218h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
21Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
220h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
228h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
22Ch |
R |
Control register high for DMA channel x for block size |
|
250h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
254h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
268h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
26Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
270h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
274h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
278h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
280h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
284h |
R |
Control register high for DMA channel x for block size |
|
2A8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
2ACh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
2C0h |
R |
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts |
|
2C8h |
R |
Raw block transfer complete interrupt status register, shows unmasked block transfer complete interrupts |
|
2E0h |
R |
Raw error interrupt status register low, shows unmasked protocol error interrupts |
|
2E4h |
R |
Raw error interrupt status register high, shows unmasked secure error interrupts |
|
2E8h |
R |
Transfer complete interrupt status register, shows masked transfer complete interrupts |
|
2F0h |
R |
Block transfer complete interrupt status register, shows masked block transfer complete interrupts |
|
308h |
R |
Error interrupt status register low, shows masked protocol error interrupts |
|
30Ch |
R |
Error interrupt status register high, shows masked secure error interrupts |
|
310h |
R/W |
Transfer complete interrupt mask register, enables or disables transfer complete interrupts |
|
318h |
R/W |
Block transfer complete interrupt mask register, enables or disables block transfer complete interrupts |
|
330h |
R/W |
Error interrupt mask register low, enables or disables protocol error interrupts |
|
334h |
R/W |
Error interrupt mask register high, enables or disables secure error interrupts |
|
338h |
R/W |
Transfer complete interrupt clear register, clears transfer complete interrupt status |
|
340h |
R/W |
Block transfer complete interrupt clear register, clears block transfer complete interrupt status |
|
358h |
R/W |
Error interrupt clear register low, clears protocol error interrupt status |
|
35Ch |
R/W |
Error interrupt clear register high, clears secure error interrupt status |
|
360h |
R |
Interrupt status register low, shows combined interrupt status |
|
364h |
R |
Interrupt status register high, shows combined interrupt status |
|
398h |
R/W |
DMA configuration register, configures global DMA controller settings |
|
3A0h |
R/W |
Channel enable register, enables or disables DMA channels |
|
3A8h |
R |
DMA ID register, Hardcoded RTK_DMAC peripheral ID |
|
3C8h |
R |
DMA component parameters register 6 low, contains component identification information |
|
3CCh |
R |
DMA component parameters register 6 high, contains component identification information |
|
3D0h |
R |
DMA component parameters register 5 low, contains component identification information |
|
3D4h |
R |
DMA component parameters register 5 high, contains component identification information |
|
3D8h |
R |
DMA component parameters register 4 low, contains component identification information |
|
3DCh |
R |
DMA component parameters register 4 high, contains component identification information |
|
3E0h |
R |
DMA component parameters register 3 low, contains component identification information |
|
3E4h |
R |
DMA component parameters register 3 high, contains component identification information |
|
3E8h |
R |
DMA component parameters register 2 low, contains component identification information |
|
3ECh |
R |
DMA component parameters register 2 high, contains component identification information |
|
3F0h |
R |
DMA component parameters register 1 low, contains component identification information |
|
3F4h |
R |
DMA component parameters register 1 high, contains component identification information |
|
3F8h |
R |
DMA component ID register low, identifies the DMA controller release date |
|
3FCh |
R |
DMA component ID register high, identifies the DMA controller rtl version |
REG_SAR0
Name: Channel 0 Source Address Register
Size: 32
Address offset: 000h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR0 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR0
Name: The read back value is channel 0 source reading address at present
Size: 32
Address offset: 004h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR0 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR0
Name: Channel 0 Destination Address Register
Size: 32
Address offset: 008h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR0 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR0
Name: The read back value is channel 0 destination writing address at present
Size: 32
Address offset: 00Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR0 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP0_L
Name: Channel 0 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 010h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP0_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL0_L
Name: Channel 0 low-32 bits Control Register
Size: 32
Address offset: 018h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL0_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL0_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL0_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL0_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL0_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL0_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL0_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL0_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL0_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL0_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL0_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL0_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL0_H
Name: Channel 0 high-32 bits Control Register
Size: 32
Address offset: 01Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL0_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG0_L
Name: Channel 0 low-32 bits Configuration Register
Size: 32
Address offset: 040h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG0_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG0_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG0_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG0_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG0_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG0_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG0_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG0_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG0_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG0_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG0_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG0_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG0_H
Name: Channel 0 high-32 bits Configuration Register
Size: 32
Address offset: 044h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG0_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG0_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG0_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG0_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG0_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG0_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR1
Name: Channel 1 Source Address Register
Size: 32
Address offset: 058h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR1 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR1
Name: The read back value is channel 1 source reading address at present
Size: 32
Address offset: 05Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR1 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR1
Name: Channel 1 Destination Address Register
Size: 32
Address offset: 060h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR1 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR1
Name: The read back value is channel 1 destination writing address at present
Size: 32
Address offset: 064h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR1 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP1_L
Name: Channel 1 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 068h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP1_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL1_L
Name: Channel 1 low-32 bits Control Register
Size: 32
Address offset: 070h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL1_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL1_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL1_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL1_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL1_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL1_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL1_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL1_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL1_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL1_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL1_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL1_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL1_H
Name: Channel 1 high-32 bits Control Register
Size: 32
Address offset: 074h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL1_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG1_L
Name: Channel 1 low-32 bits Configuration Register
Size: 32
Address offset: 098h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG1_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG1_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG1_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG1_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG1_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG1_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG1_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG1_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG1_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG1_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG1_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG1_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG1_H
Name: Channel 1 high-32 bits Configuration Register
Size: 32
Address offset: 09Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG1_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG1_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG1_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG1_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG1_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG1_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR2
Name: Channel 2 Source Address Register
Size: 32
Address offset: 0B0h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR2 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR2
Name: The read back value is channel 2 source reading address at present
Size: 32
Address offset: 0B4h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR2 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR2
Name: Channel 2 Destination Address Register
Size: 32
Address offset: 0B8h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR2 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR2
Name: The read back value is channel 2 destination writing address at present
Size: 32
Address offset: 0BCh
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR2 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP2_L
Name: Channel 2 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 0C0h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP2_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL2_L
Name: Channel 2 low-32 bits Control Register
Size: 32
Address offset: 0C8h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL2_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL2_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL2_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL2_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL2_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL2_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL2_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL2_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL2_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL2_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL2_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL2_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL2_H
Name: Channel 2 high-32 bits Control Register
Size: 32
Address offset: 0CCh
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL2_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG2_L
Name: Channel 2 low-32 bits Configuration Register
Size: 32
Address offset: 0F0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG2_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG2_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG2_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG2_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG2_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG2_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG2_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG2_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG2_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG2_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG2_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG2_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG2_H
Name: Channel 2 high-32 bits Configuration Register
Size: 32
Address offset: 0F4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG2_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG2_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG2_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG2_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG2_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG2_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR3
Name: Channel 3 Source Address Register
Size: 32
Address offset: 108h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR3 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR3
Name: The read back value is channel 3 source reading address at present
Size: 32
Address offset: 10Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR3 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR3
Name: Channel 3 Destination Address Register
Size: 32
Address offset: 110h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR3 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR3
Name: The read back value is channel 3 destination writing address at present
Size: 32
Address offset: 114h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR3 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP3_L
Name: Channel 3 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 118h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP3_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL3_L
Name: Channel 3 low-32 bits Control Register
Size: 32
Address offset: 120h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL3_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL3_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL3_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL3_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL3_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL3_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL3_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL3_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL3_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL3_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL3_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL3_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL3_H
Name: Channel 3 high-32 bits Control Register
Size: 32
Address offset: 124h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL3_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG3_L
Name: Channel 3 low-32 bits Configuration Register
Size: 32
Address offset: 148h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG3_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG3_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG3_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG3_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG3_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG3_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG3_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG3_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG3_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG3_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG3_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG3_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG3_H
Name: Channel 3 high-32 bits Configuration Register
Size: 32
Address offset: 14Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG3_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG3_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG3_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG3_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG3_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG3_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR4
Name: Channel 4 Source Address Register
Size: 32
Address offset: 160h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR4 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR4
Name: The read back value is channel 4 source reading address at present
Size: 32
Address offset: 164h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR4 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR4
Name: Channel 4 Destination Address Register
Size: 32
Address offset: 168h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR4 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR4
Name: The read back value is channel 4 destination writing address at present
Size: 32
Address offset: 16Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR4 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP4_L
Name: Channel 4 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 170h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP4_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL4_L
Name: Channel 4 low-32 bits Control Register
Size: 32
Address offset: 178h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL4_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL4_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL4_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL4_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL4_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL4_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL4_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL4_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL4_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL4_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL4_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL4_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL4_H
Name: Channel 4 high-32 bits Control Register
Size: 32
Address offset: 17Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL4_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG4_L
Name: Channel 4 low-32 bits Configuration Register
Size: 32
Address offset: 1A0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG4_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG4_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG4_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG4_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG4_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG4_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG4_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG4_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG4_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG4_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG4_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG4_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG4_H
Name: Channel 4 high-32 bits Configuration Register
Size: 32
Address offset: 1A4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG4_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG4_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG4_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG4_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG4_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG4_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR5
Name: Channel 5 Source Address Register
Size: 32
Address offset: 1B8h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR5 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR5
Name: The read back value is channel 5 source reading address at present
Size: 32
Address offset: 1BCh
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR5 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR5
Name: Channel 5 Destination Address Register
Size: 32
Address offset: 1C0h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR5 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR5
Name: The read back value is channel 5 destination writing address at present
Size: 32
Address offset: 1C4h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR5 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP5_L
Name: Channel 5 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 1C8h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP5_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL5_L
Name: Channel 5 low-32 bits Control Register
Size: 32
Address offset: 1D0h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL5_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL5_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL5_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL5_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL5_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL5_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL5_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL5_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL5_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL5_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL5_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL5_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL5_H
Name: Channel 5 high-32 bits Control Register
Size: 32
Address offset: 1D4h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL5_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG5_L
Name: Channel 5 low-32 bits Configuration Register
Size: 32
Address offset: 1F8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG5_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG5_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG5_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG5_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG5_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG5_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG5_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG5_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG5_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG5_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG5_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG5_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG5_H
Name: Channel 5 high-32 bits Configuration Register
Size: 32
Address offset: 1FCh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG5_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG5_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG5_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG5_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG5_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG5_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR6
Name: Channel 6 Source Address Register
Size: 32
Address offset: 210h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR6 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR6
Name: The read back value is channel 6 source reading address at present
Size: 32
Address offset: 214h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR6 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR6
Name: Channel 6 Destination Address Register
Size: 32
Address offset: 218h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR6 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR6
Name: The read back value is channel 6 destination writing address at present
Size: 32
Address offset: 21Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR6 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP6_L
Name: Channel 6 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 220h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP6_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL6_L
Name: Channel 6 low-32 bits Control Register
Size: 32
Address offset: 228h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL6_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL6_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL6_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL6_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL6_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL6_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL6_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL6_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL6_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL6_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL6_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL6_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL6_H
Name: Channel 6 high-32 bits Control Register
Size: 32
Address offset: 22Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL6_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG6_L
Name: Channel 6 low-32 bits Configuration Register
Size: 32
Address offset: 250h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG6_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG6_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG6_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG6_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG6_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG6_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG6_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG6_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG6_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG6_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG6_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG6_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG6_H
Name: Channel 6 high-32 bits Configuration Register
Size: 32
Address offset: 254h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG6_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG6_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG6_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG6_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG6_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG6_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR7
Name: Channel 7 Source Address Register
Size: 32
Address offset: 268h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR7 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR7
Name: The read back value is channel 7 source reading address at present
Size: 32
Address offset: 26Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR7 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR7
Name: Channel 7 Destination Address Register
Size: 32
Address offset: 270h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR7 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR7
Name: The read back value is channel 7 destination writing address at present
Size: 32
Address offset: 274h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR7 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP7_L
Name: Channel 7 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 278h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP7_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL7_L
Name: Channel 7 low-32 bits Control Register
Size: 32
Address offset: 280h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL7_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL7_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL7_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL7_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL7_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL7_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL7_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL7_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL7_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL7_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL7_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL7_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL7_H
Name: Channel 7 high-32 bits Control Register
Size: 32
Address offset: 284h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL7_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG7_L
Name: Channel 7 low-32 bits Configuration Register
Size: 32
Address offset: 2A8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG7_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG7_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG7_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG7_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG7_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG7_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG7_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG7_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG7_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG7_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG7_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG7_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG7_H
Name: Channel 7 high-32 bits Configuration Register
Size: 32
Address offset: 2ACh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG7_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG7_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG7_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG7_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG7_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG7_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_RAWTFR_L
Name: Raw Status for IntTfr Interrupt
Size: 32
Address offset: 2C0h
Read/write access: R
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWTFR_L_RAW_TFR |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWBLOCK_L
Name: Raw Status for IntBlock Interrupt
Size: 32
Address offset: 2C8h
Read/write access: R
Raw block transfer complete interrupt status register, shows unmasked block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWBLOCK_L_RAW_BLOCK |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWERR_L
Name: Raw Status for IntErr Interrupt(protocol error)
Size: 32
Address offset: 2E0h
Read/write access: R
Raw error interrupt status register low, shows unmasked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_L_RAW_ERR |
R |
0x0 |
Raw interrupt status for chn0-chn15. (Protocol error) |
REG_RAWERR_H
Name: Raw Status for non-secure access secure register error if defined
Size: 32
Address offset: 2E4h
Read/write access: R
Raw error interrupt status register high, shows unmasked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_H_RAW_ERR |
R |
0x0 |
Raw interrupt status. (Non-secure access secure register error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_STATUSTFR_L
Name: Status for IntTfr Interrupt
Size: 32
Address offset: 2E8h
Read/write access: R
Transfer complete interrupt status register, shows masked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSTFR_L_STATUS_TFR |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSBLOCK_L
Name: Status for IntBlock Interrupt
Size: 32
Address offset: 2F0h
Read/write access: R
Block transfer complete interrupt status register, shows masked block transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSBLOCK_L_STATUS_BLOCK |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSERR_L
Name: Status for IntErr Interrupt
Size: 32
Address offset: 308h
Read/write access: R
Error interrupt status register low, shows masked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_L_STATUS_ERR |
R |
0x0 |
Interrupt status for chn0-chn15. (Protocol error) |
REG_STATUSERR_H
Name: Status for non-secure access secure register error if defined
Size: 32
Address offset: 30Ch
Read/write access: R
Error interrupt status register high, shows masked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_H_STATUS_ERR |
R |
0x0 |
Interrupt status. (Non-secure access secure register error, Sec Error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_MASKTFR_L
Name: Mask for IntTfr Interrupt (chn0-7)
Size: 32
Address offset: 310h
Read/write access: R/W
Transfer complete interrupt mask register, enables or disables transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKTFR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKTFR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKBLOCK_L
Name: Mask for IntBlock Interrupt
Size: 32
Address offset: 318h
Read/write access: R/W
Block transfer complete interrupt mask register, enables or disables block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKBLOCK_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKBLOCK_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_L
Name: Mask for IntErr Interrupt
Size: 32
Address offset: 330h
Read/write access: R/W
Error interrupt mask register low, enables or disables protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKERR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_H
Name: Mask for non-secure access secure register error if defined
Size: 32
Address offset: 334h
Read/write access: R/W
Error interrupt mask register high, enables or disables secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_H_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled These bits only exist when DMAC_ SECURE_MODE has beed defined |
7:0 |
MASKERR_H_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked These bits only exist when DMAC_ SECURE_MODE has beed defined |
REG_CLEARTFR_L
Name: Clear for IntTfr Interrupt
Size: 32
Address offset: 338h
Read/write access: R/W
Transfer complete interrupt clear register, clears transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARTFR_L_CLEAR_TFR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 0 = no effect 1= clear interrupt |
REG_CLEARBLOCK_L
Name: Clear for IntBlock Interrupt
Size: 32
Address offset: 340h
Read/write access: R/W
Block transfer complete interrupt clear register, clears block transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARBLOCK_L_CLEAR_BLOCK |
R/W |
0x0 |
Interrupt clear for chn0-chn15 |
REG_CLEARERR_L
Name: Clear for IntErr Interrupt
Size: 32
Address offset: 358h
Read/write access: R/W
Error interrupt clear register low, clears protocol error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_L_CLEAR_PROTOCOL_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15. (Protocol error) |
REG_CLEARERR_H
Name: Clear for non-secure access secure register error if defined
Size: 32
Address offset: 35Ch
Read/write access: R/W
Error interrupt clear register high, clears secure error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_H_CLEAR_SEC_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 (Non-secure access secure register error, Sec Error) when DMAC_SECURE_MODE has beed defined, else it is reserved; |
REG_STATUSINT_L
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 360h
Read/write access: R
Interrupt status register low, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
STATUSINT_L_ERROR |
R |
0x0 |
OR of the contents of StatusErr register. |
3:2 |
RSVD |
R |
- |
Reserved |
1 |
STATUSINT_L_BLOCK |
R |
0x0 |
OR of the contents of StatusBlock register. |
0 |
STATUSINT_L_TFR |
R |
0x0 |
OR of the contents of StatusTfr register. |
REG_STATUSINT_H
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 364h
Read/write access: R
Interrupt status register high, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_DMACFGREG_L
Name: DMA low-32 bits Configuration Register
Size: 32
Address offset: 398h
Read/write access: R/W
DMA configuration register, configures global DMA controller settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
DMACFGREG_L_DMA_EN |
R/W |
0x1 |
RTK_DMAC Enable bit. 0 = RTK_DMAC Disabled 1 = RTK_DMAC Enabled |
REG_CHENREG_L_1
Name: DMA low-32 bits Channel Enable Register if configed chn number is less than or equal to 8
Size: 32
Address offset: 3A0h
Read/write access: R/W
Channel enable register, enables or disables DMA channels
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
CHENREG_L_1_CH_EN_WE |
R/W |
0x0 |
Channel enable write enable. |
7:0 |
CHENREG_L_1_CH_EN |
R/W |
0x0 |
Enables/Disables the channel. Setting this bit enables a channel; clearing this bit disables the channel. 0 = Disable the Channel 1 = Enable the Channel The CHENREG_L.CH_EN bit is automatically cleared by hardware to disable the channel after the last AXI transfer of the DMA transfer to the destination has completed. Software can therefore poll this bit to determine when this channel is free for a new DMA transfer. |
REG_DMAIDREG_L
Name: DMA low-32 bits ID Register
Size: 32
Address offset: 3A8h
Read/write access: R
DMA ID register, Hardcoded RTK_DMAC peripheral ID
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMAIDREG_L_DMA_ID |
R |
32'h21111118 |
Hardcoded RTK_DMAC Peripheral ID |
REG_DMA_COMP_PARAMS_6_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3C8h
Read/write access: R
DMA component parameters register 6 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH7_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH7_MAX_BLK_SIZE from config_form.vh CH7_MAX_BLK_SIZE = log2(DMAC_CH7_MAX_BLK_SIZE) + 1 |
23:16 |
CH6_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH6_MAX_BLK_SIZE from config_form.vh CH6_MAX_BLK_SIZE = log2(DMAC_CH6_MAX_BLK_SIZE) + 1 |
15:8 |
CH5_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH5_MAX_BLK_SIZE from config_form.vh CH5_MAX_BLK_SIZE = log2(DMAC_CH5_MAX_BLK_SIZE) + 1 |
7:0 |
CH4_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH4_MAX_BLK_SIZE from config_form.vh CH4_MAX_BLK_SIZE = log2(DMAC_CH4_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_6_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3CCh
Read/write access: R
DMA component parameters register 6 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH7_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH7_FIFO_DEPTH parameter. Default value is 0x0. CH7_FIFO_DEPTH = log2(DMAC_CH7_FIFO_DEPTH/8) 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH7_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_MULT_SIZE parameter. Maxium burst transaction size. CH7_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH7_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH7_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH7_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH7_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH7_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH7_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH7_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH7_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH7_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH7_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH7_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D0h
Read/write access: R
DMA component parameters register 5 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH6_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH6_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH6_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_MULT_SIZE parameter. Maxium burst transaction size. CH6_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH6_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH6_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH6_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH6_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH6_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH6_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH6_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH6_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH6_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH6_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH6_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH6_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D4h
Read/write access: R
DMA component parameters register 5 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH5_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH5_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH5_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_MULT_SIZE parameter. Maxium burst transaction size. CH5_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH5_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH5_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH5_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH5_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH5_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH5_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH5_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH5_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH5_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH5_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH5_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH5_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D8h
Read/write access: R
DMA component parameters register 4 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH4_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH4_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH4_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_MULT_SIZE parameter. Maxium burst transaction size. CH4_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH4_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH4_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH4_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH4_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH4_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH4_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH4_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112.0x0 = FALSE 0x1 = TRUE |
8 |
CH4_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH4_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH4_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH4_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH4_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3DCh
Read/write access: R
DMA component parameters register 4 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH3_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH3_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH3_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_MULT_SIZE parameter. Maxium burst transaction size. CH3_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH3_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH3_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH3_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH3_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH3_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH3_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH3_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH3_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH3_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH3_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH3_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E0h
Read/write access: R
DMA component parameters register 3 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH2_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH2_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH2_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_MULT_SIZE parameter. Maxium burst transaction size. CH2_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH2_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH2_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH2_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH2_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH2_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH2_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH2_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH2_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH2_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH2_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH2_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E4h
Read/write access: R
DMA component parameters register 3 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH1_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH1_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH1_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_MULT_SIZE parameter. Maxium burst transaction size. CH1_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH1_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH1_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH1_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH1_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH1_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH1_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH1_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH1_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH1_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH1_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH1_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E8h
Read/write access: R
DMA component parameters register 2 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH0_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH0_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH0_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_MULT_SIZE parameter. Maxium burst transaction size. CH0_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH0_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH0_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH0_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH0_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH0_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH0_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH0_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH0_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH0_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH0_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH0_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3ECh
Read/write access: R
DMA component parameters register 2 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:28 |
CH7_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
27:24 |
CH6_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
23:20 |
CH5_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
19:16 |
CH4_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
15:12 |
CH3_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
11:8 |
CH2_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
7:4 |
CH1_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
3:0 |
CH0_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
REG_DMA_COMP_PARAMS_1_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F0h
Read/write access: R
DMA component parameters register 1 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH3_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH3_MAX_BLK_SIZE from config_form.vh CH3_MAX_BLK_SIZE = log2(DMAC_CH3_MAX_BLK_SIZE) + 1 |
23:16 |
CH2_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH2_MAX_BLK_SIZE from config_form.vh CH2_MAX_BLK_SIZE = log2(DMAC_CH2_MAX_BLK_SIZE) + 1 |
15:8 |
CH1_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH1_MAX_BLK_SIZE from config_form.vh CH1_MAX_BLK_SIZE = log2(DMAC_CH1_MAX_BLK_SIZE) + 1 |
7:0 |
CH0_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH0_MAX_BLK_SIZE from config_form.vh CH0_MAX_BLK_SIZE = log2(DMAC_CH0_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_1_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F4h
Read/write access: R
DMA component parameters register 1 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
HIGH_BIT_NUM_HS_INT3 |
R |
0x0 |
Number of hardware handshake interfaces. If it is 128, this bit read value is 1. |
30 |
HIGH_BIT_NUM_HS_INT2 |
R |
0x0 |
Number of hardware handshake interfaces. If it is greater than 63 and less than 128, this bit read value is 1. |
29 |
HIGH_BIT_NUM_HS_INT1 |
R |
0x0 |
Number of hardware handshake interfaces. If it is greater than 31 and less than 64, this bit read value is 1. |
28 |
STATIC_ENDIAN_SELECT |
R |
0 |
The value of this register is derived from the DMAC_STATIC_ENDIAN_SELECT parameter. 0 = FALSE (dynamic endian fixed) 1 = TRUE (not supported) |
27 |
ADD_ENCODED_PARAMS |
R |
1 |
The value of this register is derived from the DMAC_ADD_ENCODED_PARAMS parameter. 0 = FALSE 1 = TRUE |
26:22 |
NUM_HS_INT |
R |
0x1E |
Number of hardware handshake interfaces. The value of this register is derived from the DMAC_NUM_HS_INT parameter. NUM_HAS_INT = DMAC_NUM_HS_INT[4:0] 0x00 = 0 … 0x10 = 16 |
21:18 |
RSVD |
R |
- |
Reserved |
17:16 |
M2_DATA_WIDTH |
R |
0x0 |
AXI Master2 data width. The value of this register is derived from the DMAC_M2_DATA_WIDTH parameter. Master2 data width should be equal to that of Master 1. M2_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
15:14 |
M1_DATA_WIDTH |
R |
0x0 |
AXI Master1 data width. The value of this register is derived from the DMAC_M1_DATA_WIDTH parameter. Master1 data width should be equal to that of Master 2. M1_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
13:12 |
S_DATA_WIDTH |
R |
0x0 |
APB slave interface data width.The value of this register is derived from the DMAC_S_DATA_WIDTH parameter. The width is fixed to 32 bits for now. S_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = Reserved 0x2 = Reserved 0x3 = Reserved |
11:10 |
NUM_MASTER_INT |
R |
0x1 |
Number of master interface. The value of this register is derived from the DMAC_NUM_MASTER_INT parameter. This value is fixed to 1 (only 2 AXI masters supported now.) 0x0 = Reserved 0x1 = 2 0x2 = Reserved 0x3 = Reserved |
9:6 |
NUM_CHANNELS |
R |
0x7 |
Number of channels. The value of this register is derived from the DMAC_NUM_CHASNNELS parameter. NUM_CHANNELS = DMAC_NUM_CHASNNELS -1 0x0 = 1 … 0xf = 16 |
5:2 |
RSVD |
R |
- |
Reserved |
1:0 |
INTR_IO |
R |
0x0 |
Interrupt output format.The value of this register is derived from the DMAC_INTR_IO parameter. 0x0 = ALL 0x1 = TYPE 0x2 = COMBINED 0x3 = reserved |
REG_DMA_COMPONENT_ID_REGS_L
Name: DMAC ID
Size: 32
Address offset: 3F8h
Read/write access: R
DMA component ID register low, identifies the DMA controller release date
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMA_COMPONENT_ID |
R |
32'h21111118 |
DMAC ID (release_date_. Configure it in config form. |
REG_DMA_COMPONENT_ID_REGS_H
Name: It is obtained from the high 32 bits from git logs in git server.
Size: 32
Address offset: 3FCh
Read/write access: R
DMA component ID register high, identifies the DMA controller rtl version
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RTL_GIT_VER |
R |
32'h00201028 |
It is obtained from the high 32 bits from git logs in git server. |
REGISTER_CONTENTS=RTL8720E
REGISTER_CONTENTS=RTL8720E
REGISTER_CONTENTS=RTL8720E
Base Address: 0x400E0000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
004h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
008h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
00Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
010h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
018h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
01Ch |
R |
Control register high for DMA channel x for block size |
|
040h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
044h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
058h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
05Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
060h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
064h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
068h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
070h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
074h |
R |
Control register high for DMA channel x for block size |
|
098h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
09Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
0B0h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
0B4h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
0B8h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
0BCh |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
0C0h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
0C8h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
0CCh |
R |
Control register high for DMA channel x for block size |
|
0F0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
0F4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
108h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
10Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
110h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
114h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
118h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
120h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
124h |
R |
Control register high for DMA channel x for block size |
|
148h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
14Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
160h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
164h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
168h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
16Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
170h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
178h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
17Ch |
R |
Control register high for DMA channel x for block size |
|
1A0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1A4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
1B8h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
1BCh |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
1C0h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
1C4h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
1C8h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
1D0h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
1D4h |
R |
Control register high for DMA channel x for block size |
|
1F8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1FCh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
210h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
214h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
218h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
21Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
220h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
228h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
22Ch |
R |
Control register high for DMA channel x for block size |
|
250h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
254h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
268h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
26Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
270h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
274h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
278h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
280h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
284h |
R |
Control register high for DMA channel x for block size |
|
2A8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
2ACh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
2C0h |
R |
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts |
|
2C8h |
R |
Raw block transfer complete interrupt status register, shows unmasked block transfer complete interrupts |
|
2E0h |
R |
Raw error interrupt status register low, shows unmasked protocol error interrupts |
|
2E4h |
R |
Raw error interrupt status register high, shows unmasked secure error interrupts |
|
2E8h |
R |
Transfer complete interrupt status register, shows masked transfer complete interrupts |
|
2F0h |
R |
Block transfer complete interrupt status register, shows masked block transfer complete interrupts |
|
308h |
R |
Error interrupt status register low, shows masked protocol error interrupts |
|
30Ch |
R |
Error interrupt status register high, shows masked secure error interrupts |
|
310h |
R/W |
Transfer complete interrupt mask register, enables or disables transfer complete interrupts |
|
318h |
R/W |
Block transfer complete interrupt mask register, enables or disables block transfer complete interrupts |
|
330h |
R/W |
Error interrupt mask register low, enables or disables protocol error interrupts |
|
334h |
R/W |
Error interrupt mask register high, enables or disables secure error interrupts |
|
338h |
R/W |
Transfer complete interrupt clear register, clears transfer complete interrupt status |
|
340h |
R/W |
Block transfer complete interrupt clear register, clears block transfer complete interrupt status |
|
358h |
R/W |
Error interrupt clear register low, clears protocol error interrupt status |
|
35Ch |
R/W |
Error interrupt clear register high, clears secure error interrupt status |
|
360h |
R |
Interrupt status register low, shows combined interrupt status |
|
364h |
R |
Interrupt status register high, shows combined interrupt status |
|
398h |
R/W |
DMA configuration register, configures global DMA controller settings |
|
3A0h |
R/W |
Channel enable register, enables or disables DMA channels |
|
3A8h |
R |
DMA ID register, Hardcoded RTK_DMAC peripheral ID |
|
3C8h |
R |
DMA component parameters register 6 low, contains component identification information |
|
3CCh |
R |
DMA component parameters register 6 high, contains component identification information |
|
3D0h |
R |
DMA component parameters register 5 low, contains component identification information |
|
3D4h |
R |
DMA component parameters register 5 high, contains component identification information |
|
3D8h |
R |
DMA component parameters register 4 low, contains component identification information |
|
3DCh |
R |
DMA component parameters register 4 high, contains component identification information |
|
3E0h |
R |
DMA component parameters register 3 low, contains component identification information |
|
3E4h |
R |
DMA component parameters register 3 high, contains component identification information |
|
3E8h |
R |
DMA component parameters register 2 low, contains component identification information |
|
3ECh |
R |
DMA component parameters register 2 high, contains component identification information |
|
3F0h |
R |
DMA component parameters register 1 low, contains component identification information |
|
3F4h |
R |
DMA component parameters register 1 high, contains component identification information |
|
3F8h |
R |
DMA component ID register low, identifies the DMA controller release date |
|
3FCh |
R |
DMA component ID register high, identifies the DMA controller rtl version |
REG_SAR0
Name: Channel 0 Source Address Register
Size: 32
Address offset: 000h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR0 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR0
Name: The read back value is channel 0 source reading address at present
Size: 32
Address offset: 004h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR0 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR0
Name: Channel 0 Destination Address Register
Size: 32
Address offset: 008h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR0 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR0
Name: The read back value is channel 0 destination writing address at present
Size: 32
Address offset: 00Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR0 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP0_L
Name: Channel 0 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 010h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP0_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL0_L
Name: Channel 0 low-32 bits Control Register
Size: 32
Address offset: 018h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL0_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL0_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL0_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL0_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL0_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL0_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL0_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL0_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL0_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL0_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL0_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL0_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL0_H
Name: Channel 0 high-32 bits Control Register
Size: 32
Address offset: 01Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL0_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG0_L
Name: Channel 0 low-32 bits Configuration Register
Size: 32
Address offset: 040h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG0_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG0_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG0_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG0_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG0_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG0_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG0_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG0_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG0_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG0_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG0_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG0_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG0_H
Name: Channel 0 high-32 bits Configuration Register
Size: 32
Address offset: 044h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:19 |
RSVD |
R |
- |
Reserved |
18 |
CFG0_H_EXTENDED_DEST_PER2 |
R/W |
0x1 |
The extended 5th bit of DEST_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
17 |
CFG0_H_EXTENDED_SRC_PER2 |
R/W |
0x2 |
The extended 5th bit of SRC_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
16 |
CFG0_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG0_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG0_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG0_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG0_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG0_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR1
Name: Channel 1 Source Address Register
Size: 32
Address offset: 058h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR1 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR1
Name: The read back value is channel 1 source reading address at present
Size: 32
Address offset: 05Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR1 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR1
Name: Channel 1 Destination Address Register
Size: 32
Address offset: 060h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR1 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR1
Name: The read back value is channel 1 destination writing address at present
Size: 32
Address offset: 064h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR1 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP1_L
Name: Channel 1 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 068h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP1_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL1_L
Name: Channel 1 low-32 bits Control Register
Size: 32
Address offset: 070h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL1_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL1_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL1_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL1_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL1_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL1_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL1_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL1_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL1_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL1_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL1_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL1_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL1_H
Name: Channel 1 high-32 bits Control Register
Size: 32
Address offset: 074h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL1_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG1_L
Name: Channel 1 low-32 bits Configuration Register
Size: 32
Address offset: 098h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG1_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG1_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG1_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG1_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG1_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG1_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG1_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG1_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG1_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG1_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG1_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG1_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG1_H
Name: Channel 1 high-32 bits Configuration Register
Size: 32
Address offset: 09Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:19 |
RSVD |
R |
- |
Reserved |
18 |
CFG1_H_EXTENDED_DEST_PER2 |
R/W |
0x1 |
The extended 5th bit of DEST_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
17 |
CFG1_H_EXTENDED_SRC_PER2 |
R/W |
0x2 |
The extended 5th bit of SRC_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
16 |
CFG1_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG1_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG1_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG1_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG1_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG1_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR2
Name: Channel 2 Source Address Register
Size: 32
Address offset: 0B0h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR2 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR2
Name: The read back value is channel 2 source reading address at present
Size: 32
Address offset: 0B4h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR2 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR2
Name: Channel 2 Destination Address Register
Size: 32
Address offset: 0B8h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR2 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR2
Name: The read back value is channel 2 destination writing address at present
Size: 32
Address offset: 0BCh
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR2 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP2_L
Name: Channel 2 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 0C0h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP2_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL2_L
Name: Channel 2 low-32 bits Control Register
Size: 32
Address offset: 0C8h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL2_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL2_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL2_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL2_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL2_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL2_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL2_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL2_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL2_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL2_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL2_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL2_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL2_H
Name: Channel 2 high-32 bits Control Register
Size: 32
Address offset: 0CCh
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL2_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG2_L
Name: Channel 2 low-32 bits Configuration Register
Size: 32
Address offset: 0F0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG2_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG2_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG2_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG2_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG2_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG2_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG2_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG2_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG2_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG2_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG2_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG2_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG2_H
Name: Channel 2 high-32 bits Configuration Register
Size: 32
Address offset: 0F4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:19 |
RSVD |
R |
- |
Reserved |
18 |
CFG2_H_EXTENDED_DEST_PER2 |
R/W |
0x1 |
The extended 5th bit of DEST_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
17 |
CFG2_H_EXTENDED_SRC_PER2 |
R/W |
0x2 |
The extended 5th bit of SRC_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
16 |
CFG2_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG2_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG2_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG2_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG2_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG2_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR3
Name: Channel 3 Source Address Register
Size: 32
Address offset: 108h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR3 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR3
Name: The read back value is channel 3 source reading address at present
Size: 32
Address offset: 10Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR3 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR3
Name: Channel 3 Destination Address Register
Size: 32
Address offset: 110h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR3 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR3
Name: The read back value is channel 3 destination writing address at present
Size: 32
Address offset: 114h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR3 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP3_L
Name: Channel 3 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 118h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP3_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL3_L
Name: Channel 3 low-32 bits Control Register
Size: 32
Address offset: 120h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL3_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL3_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL3_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL3_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL3_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL3_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL3_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL3_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL3_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL3_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL3_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL3_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL3_H
Name: Channel 3 high-32 bits Control Register
Size: 32
Address offset: 124h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL3_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG3_L
Name: Channel 3 low-32 bits Configuration Register
Size: 32
Address offset: 148h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG3_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG3_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG3_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG3_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG3_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG3_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG3_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG3_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG3_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG3_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG3_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG3_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG3_H
Name: Channel 3 high-32 bits Configuration Register
Size: 32
Address offset: 14Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:19 |
RSVD |
R |
- |
Reserved |
18 |
CFG3_H_EXTENDED_DEST_PER2 |
R/W |
0x1 |
The extended 5th bit of DEST_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
17 |
CFG3_H_EXTENDED_SRC_PER2 |
R/W |
0x2 |
The extended 5th bit of SRC_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
16 |
CFG3_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG3_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG3_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG3_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG3_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG3_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR4
Name: Channel 4 Source Address Register
Size: 32
Address offset: 160h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR4 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR4
Name: The read back value is channel 4 source reading address at present
Size: 32
Address offset: 164h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR4 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR4
Name: Channel 4 Destination Address Register
Size: 32
Address offset: 168h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR4 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR4
Name: The read back value is channel 4 destination writing address at present
Size: 32
Address offset: 16Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR4 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP4_L
Name: Channel 4 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 170h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP4_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL4_L
Name: Channel 4 low-32 bits Control Register
Size: 32
Address offset: 178h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL4_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL4_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL4_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL4_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL4_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL4_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL4_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL4_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL4_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL4_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL4_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL4_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL4_H
Name: Channel 4 high-32 bits Control Register
Size: 32
Address offset: 17Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL4_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG4_L
Name: Channel 4 low-32 bits Configuration Register
Size: 32
Address offset: 1A0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG4_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG4_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG4_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG4_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG4_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG4_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG4_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG4_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG4_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG4_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG4_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG4_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG4_H
Name: Channel 4 high-32 bits Configuration Register
Size: 32
Address offset: 1A4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:19 |
RSVD |
R |
- |
Reserved |
18 |
CFG4_H_EXTENDED_DEST_PER2 |
R/W |
0x1 |
The extended 5th bit of DEST_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
17 |
CFG4_H_EXTENDED_SRC_PER2 |
R/W |
0x2 |
The extended 5th bit of SRC_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
16 |
CFG4_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG4_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG4_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG4_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG4_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG4_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR5
Name: Channel 5 Source Address Register
Size: 32
Address offset: 1B8h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR5 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR5
Name: The read back value is channel 5 source reading address at present
Size: 32
Address offset: 1BCh
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR5 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR5
Name: Channel 5 Destination Address Register
Size: 32
Address offset: 1C0h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR5 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR5
Name: The read back value is channel 5 destination writing address at present
Size: 32
Address offset: 1C4h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR5 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP5_L
Name: Channel 5 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 1C8h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP5_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL5_L
Name: Channel 5 low-32 bits Control Register
Size: 32
Address offset: 1D0h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL5_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL5_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL5_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL5_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL5_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL5_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL5_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL5_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL5_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL5_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL5_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL5_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL5_H
Name: Channel 5 high-32 bits Control Register
Size: 32
Address offset: 1D4h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL5_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG5_L
Name: Channel 5 low-32 bits Configuration Register
Size: 32
Address offset: 1F8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG5_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG5_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG5_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG5_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG5_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG5_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG5_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG5_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG5_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG5_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG5_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG5_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG5_H
Name: Channel 5 high-32 bits Configuration Register
Size: 32
Address offset: 1FCh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:19 |
RSVD |
R |
- |
Reserved |
18 |
CFG5_H_EXTENDED_DEST_PER2 |
R/W |
0x1 |
The extended 5th bit of DEST_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
17 |
CFG5_H_EXTENDED_SRC_PER2 |
R/W |
0x2 |
The extended 5th bit of SRC_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
16 |
CFG5_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG5_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG5_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG5_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG5_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG5_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR6
Name: Channel 6 Source Address Register
Size: 32
Address offset: 210h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR6 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR6
Name: The read back value is channel 6 source reading address at present
Size: 32
Address offset: 214h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR6 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR6
Name: Channel 6 Destination Address Register
Size: 32
Address offset: 218h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR6 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR6
Name: The read back value is channel 6 destination writing address at present
Size: 32
Address offset: 21Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR6 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP6_L
Name: Channel 6 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 220h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP6_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL6_L
Name: Channel 6 low-32 bits Control Register
Size: 32
Address offset: 228h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL6_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL6_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL6_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL6_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL6_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL6_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL6_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL6_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL6_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL6_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL6_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL6_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL6_H
Name: Channel 6 high-32 bits Control Register
Size: 32
Address offset: 22Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL6_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG6_L
Name: Channel 6 low-32 bits Configuration Register
Size: 32
Address offset: 250h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG6_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG6_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG6_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG6_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG6_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG6_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG6_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG6_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG6_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG6_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG6_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG6_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG6_H
Name: Channel 6 high-32 bits Configuration Register
Size: 32
Address offset: 254h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:19 |
RSVD |
R |
- |
Reserved |
18 |
CFG6_H_EXTENDED_DEST_PER2 |
R/W |
0x1 |
The extended 5th bit of DEST_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
17 |
CFG6_H_EXTENDED_SRC_PER2 |
R/W |
0x2 |
The extended 5th bit of SRC_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
16 |
CFG6_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG6_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG6_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG6_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG6_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG6_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SAR7
Name: Channel 7 Source Address Register
Size: 32
Address offset: 268h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR7 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR7
Name: The read back value is channel 7 source reading address at present
Size: 32
Address offset: 26Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR7 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR7
Name: Channel 7 Destination Address Register
Size: 32
Address offset: 270h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR7 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR7
Name: The read back value is channel 7 destination writing address at present
Size: 32
Address offset: 274h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR7 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP7_L
Name: Channel 7 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 278h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP7_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL7_L
Name: Channel 7 low-32 bits Control Register
Size: 32
Address offset: 280h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL7_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL7_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL7_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL7_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL7_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL7_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL7_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL7_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL7_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL7_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL7_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL7_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL7_H
Name: Channel 7 high-32 bits Control Register
Size: 32
Address offset: 284h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL7_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG7_L
Name: Channel 7 low-32 bits Configuration Register
Size: 32
Address offset: 2A8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG7_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG7_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG7_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG7_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG7_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG7_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG7_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG7_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG7_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG7_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG7_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG7_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG7_H
Name: Channel 7 high-32 bits Configuration Register
Size: 32
Address offset: 2ACh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:19 |
RSVD |
R |
- |
Reserved |
18 |
CFG7_H_EXTENDED_DEST_PER2 |
R/W |
0x1 |
The extended 5th bit of DEST_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
17 |
CFG7_H_EXTENDED_SRC_PER2 |
R/W |
0x2 |
The extended 5th bit of SRC_PER when hardware handshake interfaces number is configured to (32, 64], else this bit can only be read. |
16 |
CFG7_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG7_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG7_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG7_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG7_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG7_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_RAWTFR_L
Name: Raw Status for IntTfr Interrupt
Size: 32
Address offset: 2C0h
Read/write access: R
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWTFR_L_RAW_TFR |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWBLOCK_L
Name: Raw Status for IntBlock Interrupt
Size: 32
Address offset: 2C8h
Read/write access: R
Raw block transfer complete interrupt status register, shows unmasked block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWBLOCK_L_RAW_BLOCK |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWERR_L
Name: Raw Status for IntErr Interrupt(protocol error)
Size: 32
Address offset: 2E0h
Read/write access: R
Raw error interrupt status register low, shows unmasked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_L_RAW_ERR |
R |
0x0 |
Raw interrupt status for chn0-chn15. (Protocol error) |
REG_RAWERR_H
Name: Raw Status for non-secure access secure register error if defined
Size: 32
Address offset: 2E4h
Read/write access: R
Raw error interrupt status register high, shows unmasked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_H_RAW_ERR |
R |
0x0 |
Raw interrupt status. (Non-secure access secure register error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_STATUSTFR_L
Name: Status for IntTfr Interrupt
Size: 32
Address offset: 2E8h
Read/write access: R
Transfer complete interrupt status register, shows masked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSTFR_L_STATUS_TFR |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSBLOCK_L
Name: Status for IntBlock Interrupt
Size: 32
Address offset: 2F0h
Read/write access: R
Block transfer complete interrupt status register, shows masked block transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSBLOCK_L_STATUS_BLOCK |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSERR_L
Name: Status for IntErr Interrupt
Size: 32
Address offset: 308h
Read/write access: R
Error interrupt status register low, shows masked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_L_STATUS_ERR |
R |
0x0 |
Interrupt status for chn0-chn15. (Protocol error) |
REG_STATUSERR_H
Name: Status for non-secure access secure register error if defined
Size: 32
Address offset: 30Ch
Read/write access: R
Error interrupt status register high, shows masked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_H_STATUS_ERR |
R |
0x0 |
Interrupt status. (Non-secure access secure register error, Sec Error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_MASKTFR_L
Name: Mask for IntTfr Interrupt (chn0-7)
Size: 32
Address offset: 310h
Read/write access: R/W
Transfer complete interrupt mask register, enables or disables transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKTFR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKTFR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKBLOCK_L
Name: Mask for IntBlock Interrupt
Size: 32
Address offset: 318h
Read/write access: R/W
Block transfer complete interrupt mask register, enables or disables block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKBLOCK_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKBLOCK_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_L
Name: Mask for IntErr Interrupt
Size: 32
Address offset: 330h
Read/write access: R/W
Error interrupt mask register low, enables or disables protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKERR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_H
Name: Mask for non-secure access secure register error if defined
Size: 32
Address offset: 334h
Read/write access: R/W
Error interrupt mask register high, enables or disables secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_H_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled These bits only exist when DMAC_ SECURE_MODE has beed defined |
7:0 |
MASKERR_H_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked These bits only exist when DMAC_ SECURE_MODE has beed defined |
REG_CLEARTFR_L
Name: Clear for IntTfr Interrupt
Size: 32
Address offset: 338h
Read/write access: R/W
Transfer complete interrupt clear register, clears transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARTFR_L_CLEAR_TFR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 0 = no effect 1= clear interrupt |
REG_CLEARBLOCK_L
Name: Clear for IntBlock Interrupt
Size: 32
Address offset: 340h
Read/write access: R/W
Block transfer complete interrupt clear register, clears block transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARBLOCK_L_CLEAR_BLOCK |
R/W |
0x0 |
Interrupt clear for chn0-chn15 |
REG_CLEARERR_L
Name: Clear for IntErr Interrupt
Size: 32
Address offset: 358h
Read/write access: R/W
Error interrupt clear register low, clears protocol error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_L_CLEAR_PROTOCOL_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15. (Protocol error) |
REG_CLEARERR_H
Name: Clear for non-secure access secure register error if defined
Size: 32
Address offset: 35Ch
Read/write access: R/W
Error interrupt clear register high, clears secure error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_H_CLEAR_SEC_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 (Non-secure access secure register error, Sec Error) when DMAC_SECURE_MODE has beed defined, else it is reserved; |
REG_STATUSINT_L
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 360h
Read/write access: R
Interrupt status register low, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
STATUSINT_L_ERROR |
R |
0x0 |
OR of the contents of StatusErr register. |
3:2 |
RSVD |
R |
- |
Reserved |
1 |
STATUSINT_L_BLOCK |
R |
0x0 |
OR of the contents of StatusBlock register. |
0 |
STATUSINT_L_TFR |
R |
0x0 |
OR of the contents of StatusTfr register. |
REG_STATUSINT_H
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 364h
Read/write access: R
Interrupt status register high, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_DMACFGREG_L
Name: DMA low-32 bits Configuration Register
Size: 32
Address offset: 398h
Read/write access: R/W
DMA configuration register, configures global DMA controller settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
DMACFGREG_L_DMA_EN |
R/W |
0x1 |
RTK_DMAC Enable bit. 0 = RTK_DMAC Disabled 1 = RTK_DMAC Enabled |
REG_CHENREG_L_1
Name: DMA low-32 bits Channel Enable Register if configed chn number is less than or equal to 8
Size: 32
Address offset: 3A0h
Read/write access: R/W
Channel enable register, enables or disables DMA channels
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
CHENREG_L_1_CH_EN_WE |
R/W |
0x0 |
Channel enable write enable. |
7:0 |
CHENREG_L_1_CH_EN |
R/W |
0x0 |
Enables/Disables the channel. Setting this bit enables a channel; clearing this bit disables the channel. 0 = Disable the Channel 1 = Enable the Channel The CHENREG_L.CH_EN bit is automatically cleared by hardware to disable the channel after the last AXI transfer of the DMA transfer to the destination has completed. Software can therefore poll this bit to determine when this channel is free for a new DMA transfer. |
REG_DMAIDREG_L
Name: DMA low-32 bits ID Register
Size: 32
Address offset: 3A8h
Read/write access: R
DMA ID register, Hardcoded RTK_DMAC peripheral ID
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMAIDREG_L_DMA_ID |
R |
32'h21071318 |
Hardcoded RTK_DMAC Peripheral ID |
REG_DMA_COMP_PARAMS_6_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3C8h
Read/write access: R
DMA component parameters register 6 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH7_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH7_MAX_BLK_SIZE from config_form.vh CH7_MAX_BLK_SIZE = log2(DMAC_CH7_MAX_BLK_SIZE) + 1 |
23:16 |
CH6_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH6_MAX_BLK_SIZE from config_form.vh CH6_MAX_BLK_SIZE = log2(DMAC_CH6_MAX_BLK_SIZE) + 1 |
15:8 |
CH5_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH5_MAX_BLK_SIZE from config_form.vh CH5_MAX_BLK_SIZE = log2(DMAC_CH5_MAX_BLK_SIZE) + 1 |
7:0 |
CH4_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH4_MAX_BLK_SIZE from config_form.vh CH4_MAX_BLK_SIZE = log2(DMAC_CH4_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_6_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3CCh
Read/write access: R
DMA component parameters register 6 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH7_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH7_FIFO_DEPTH parameter. Default value is 0x0. CH7_FIFO_DEPTH = log2(DMAC_CH7_FIFO_DEPTH/8) 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH7_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_MULT_SIZE parameter. Maxium burst transaction size. CH7_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH7_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH7_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH7_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH7_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH7_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH7_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH7_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH7_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH7_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH7_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH7_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D0h
Read/write access: R
DMA component parameters register 5 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH6_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH6_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH6_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_MULT_SIZE parameter. Maxium burst transaction size. CH6_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH6_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH6_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH6_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH6_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH6_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH6_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH6_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH6_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH6_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH6_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH6_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH6_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D4h
Read/write access: R
DMA component parameters register 5 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH5_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH5_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH5_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_MULT_SIZE parameter. Maxium burst transaction size. CH5_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH5_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH5_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH5_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH5_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH5_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH5_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH5_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH5_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH5_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH5_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH5_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH5_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D8h
Read/write access: R
DMA component parameters register 4 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH4_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH4_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH4_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_MULT_SIZE parameter. Maxium burst transaction size. CH4_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH4_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH4_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH4_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH4_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH4_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH4_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH4_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112.0x0 = FALSE 0x1 = TRUE |
8 |
CH4_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH4_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH4_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH4_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH4_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3DCh
Read/write access: R
DMA component parameters register 4 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH3_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH3_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH3_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_MULT_SIZE parameter. Maxium burst transaction size. CH3_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH3_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH3_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH3_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH3_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH3_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH3_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH3_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH3_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH3_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH3_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH3_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E0h
Read/write access: R
DMA component parameters register 3 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH2_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH2_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH2_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_MULT_SIZE parameter. Maxium burst transaction size. CH2_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH2_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH2_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH2_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH2_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH2_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH2_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH2_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH2_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH2_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH2_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH2_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E4h
Read/write access: R
DMA component parameters register 3 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH1_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH1_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH1_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_MULT_SIZE parameter. Maxium burst transaction size. CH1_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH1_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH1_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH1_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH1_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH1_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH1_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH1_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH1_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH1_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH1_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH1_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E8h
Read/write access: R
DMA component parameters register 2 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH0_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH0_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH0_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_MULT_SIZE parameter. Maxium burst transaction size. CH0_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH0_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH0_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH0_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH0_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH0_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH0_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH0_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH0_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH0_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH0_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH0_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3ECh
Read/write access: R
DMA component parameters register 2 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:28 |
CH7_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
27:24 |
CH6_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
23:20 |
CH5_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
19:16 |
CH4_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
15:12 |
CH3_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
11:8 |
CH2_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
7:4 |
CH1_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
3:0 |
CH0_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
REG_DMA_COMP_PARAMS_1_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F0h
Read/write access: R
DMA component parameters register 1 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH3_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH3_MAX_BLK_SIZE from config_form.vh CH3_MAX_BLK_SIZE = log2(DMAC_CH3_MAX_BLK_SIZE) + 1 |
23:16 |
CH2_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH2_MAX_BLK_SIZE from config_form.vh CH2_MAX_BLK_SIZE = log2(DMAC_CH2_MAX_BLK_SIZE) + 1 |
15:8 |
CH1_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH1_MAX_BLK_SIZE from config_form.vh CH1_MAX_BLK_SIZE = log2(DMAC_CH1_MAX_BLK_SIZE) + 1 |
7:0 |
CH0_MAX_BLK_SIZE |
R |
0x10 |
The value of this register is derived from the DMAC_CH0_MAX_BLK_SIZE from config_form.vh CH0_MAX_BLK_SIZE = log2(DMAC_CH0_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_1_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F4h
Read/write access: R
DMA component parameters register 1 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
HIGH_BIT_NUM_HS_INT3 |
R |
0x0 |
Number of hardware handshake interfaces. If it is 128, this bit read value is 1. |
30 |
HIGH_BIT_NUM_HS_INT2 |
R |
0x0 |
Number of hardware handshake interfaces. If it is greater than 63 and less than 128, this bit read value is 1. |
29 |
HIGH_BIT_NUM_HS_INT1 |
R |
0x1 |
Number of hardware handshake interfaces. If it is greater than 31 and less than 64, this bit read value is 1. |
28 |
STATIC_ENDIAN_SELECT |
R |
0 |
The value of this register is derived from the DMAC_STATIC_ENDIAN_SELECT parameter. 0 = FALSE (dynamic endian fixed) 1 = TRUE (not supported) |
27 |
ADD_ENCODED_PARAMS |
R |
1 |
The value of this register is derived from the DMAC_ADD_ENCODED_PARAMS parameter. 0 = FALSE 1 = TRUE |
26:22 |
NUM_HS_INT |
R |
0x22 |
Number of hardware handshake interfaces. The value of this register is derived from the DMAC_NUM_HS_INT parameter. NUM_HAS_INT = DMAC_NUM_HS_INT[4:0] 0x00 = 0 … 0x10 = 16 |
21:18 |
RSVD |
R |
- |
Reserved |
17:16 |
M2_DATA_WIDTH |
R |
0x0 |
AXI Master2 data width. The value of this register is derived from the DMAC_M2_DATA_WIDTH parameter. Master2 data width should be equal to that of Master 1. M2_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
15:14 |
M1_DATA_WIDTH |
R |
0x0 |
AXI Master1 data width. The value of this register is derived from the DMAC_M1_DATA_WIDTH parameter. Master1 data width should be equal to that of Master 2. M1_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
13:12 |
S_DATA_WIDTH |
R |
0x0 |
APB slave interface data width.The value of this register is derived from the DMAC_S_DATA_WIDTH parameter. The width is fixed to 32 bits for now. S_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = Reserved 0x2 = Reserved 0x3 = Reserved |
11:10 |
NUM_MASTER_INT |
R |
0x1 |
Number of master interface. The value of this register is derived from the DMAC_NUM_MASTER_INT parameter. This value is fixed to 1 (only 2 AXI masters supported now.) 0x0 = Reserved 0x1 = 2 0x2 = Reserved 0x3 = Reserved |
9:6 |
NUM_CHANNELS |
R |
0x7 |
Number of channels. The value of this register is derived from the DMAC_NUM_CHASNNELS parameter. NUM_CHANNELS = DMAC_NUM_CHASNNELS -1 0x0 = 1 … 0xf = 16 |
5:2 |
RSVD |
R |
- |
Reserved |
1:0 |
INTR_IO |
R |
0x0 |
Interrupt output format.The value of this register is derived from the DMAC_INTR_IO parameter. 0x0 = ALL 0x1 = TYPE 0x2 = COMBINED 0x3 = reserved |
REG_DMA_COMPONENT_ID_REGS_L
Name: DMAC ID
Size: 32
Address offset: 3F8h
Read/write access: R
DMA component ID register low, identifies the DMA controller release date
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMA_COMPONENT_ID |
R |
32'h21071318 |
DMAC ID (release_date_. Configure it in config form. |
REG_DMA_COMPONENT_ID_REGS_H
Name: It is obtained from the high 32 bits from git logs in git server.
Size: 32
Address offset: 3FCh
Read/write access: R
DMA component ID register high, identifies the DMA controller rtl version
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RTL_GIT_VER |
R |
32'h00201028 |
It is obtained from the high 32 bits from git logs in git server. |
Base Address: 0x40120000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
004h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
008h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
00Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
010h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
018h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
01Ch |
R |
Control register high for DMA channel x for block size |
|
040h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
044h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
048h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
04Ch |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
050h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
054h |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
058h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
05Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
060h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
064h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
068h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
070h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
074h |
R |
Control register high for DMA channel x for block size |
|
098h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
09Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
0A0h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
0A4h |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
0A8h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
0ACh |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
0B0h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
0B4h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
0B8h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
0BCh |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
0C0h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
0C8h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
0CCh |
R |
Control register high for DMA channel x for block size |
|
0F0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
0F4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
0F8h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
0FCh |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
100h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
104h |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
108h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
10Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
110h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
114h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
118h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
120h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
124h |
R |
Control register high for DMA channel x for block size |
|
148h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
14Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
150h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
154h |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
158h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
15Ch |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
160h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
164h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
168h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
16Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
170h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
178h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
17Ch |
R |
Control register high for DMA channel x for block size |
|
1A0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1A4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
1A8h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
1ACh |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
1B0h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
1B4h |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
1B8h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
1BCh |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
1C0h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
1C4h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
1C8h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
1D0h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
1D4h |
R |
Control register high for DMA channel x for block size |
|
1F8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1FCh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
200h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
204h |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
208h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
20Ch |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
210h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
214h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
218h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
21Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
220h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
228h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
22Ch |
R |
Control register high for DMA channel x for block size |
|
250h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
254h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
258h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
25Ch |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
260h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
264h |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
268h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
26Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
270h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
274h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
278h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
280h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
284h |
R |
Control register high for DMA channel x for block size |
|
2A8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
2ACh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
2B0h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
2B4h |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
2B8h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
2BCh |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
2C0h |
R |
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts |
|
2C8h |
R |
Raw block transfer complete interrupt status register, shows unmasked block transfer complete interrupts |
|
2E0h |
R |
Raw error interrupt status register low, shows unmasked protocol error interrupts |
|
2E4h |
R |
Raw error interrupt status register high, shows unmasked secure error interrupts |
|
2E8h |
R |
Transfer complete interrupt status register, shows masked transfer complete interrupts |
|
2F0h |
R |
Block transfer complete interrupt status register, shows masked block transfer complete interrupts |
|
308h |
R |
Error interrupt status register low, shows masked protocol error interrupts |
|
30Ch |
R |
Error interrupt status register high, shows masked secure error interrupts |
|
310h |
R/W |
Transfer complete interrupt mask register, enables or disables transfer complete interrupts |
|
318h |
R/W |
Block transfer complete interrupt mask register, enables or disables block transfer complete interrupts |
|
330h |
R/W |
Error interrupt mask register low, enables or disables protocol error interrupts |
|
334h |
R/W |
Error interrupt mask register high, enables or disables secure error interrupts |
|
338h |
R/W |
Transfer complete interrupt clear register, clears transfer complete interrupt status |
|
340h |
R/W |
Block transfer complete interrupt clear register, clears block transfer complete interrupt status |
|
358h |
R/W |
Error interrupt clear register low, clears protocol error interrupt status |
|
35Ch |
R/W |
Error interrupt clear register high, clears secure error interrupt status |
|
360h |
R |
Interrupt status register low, shows combined interrupt status |
|
364h |
R |
Interrupt status register high, shows combined interrupt status |
|
398h |
R/W |
DMA configuration register, configures global DMA controller settings |
|
3A0h |
R/W |
Channel enable register, enables or disables DMA channels |
|
3A8h |
R |
DMA ID register, Hardcoded RTK_DMAC peripheral ID |
|
3C8h |
R |
DMA component parameters register 6 low, contains component identification information |
|
3CCh |
R |
DMA component parameters register 6 high, contains component identification information |
|
3D0h |
R |
DMA component parameters register 5 low, contains component identification information |
|
3D4h |
R |
DMA component parameters register 5 high, contains component identification information |
|
3D8h |
R |
DMA component parameters register 4 low, contains component identification information |
|
3DCh |
R |
DMA component parameters register 4 high, contains component identification information |
|
3E0h |
R |
DMA component parameters register 3 low, contains component identification information |
|
3E4h |
R |
DMA component parameters register 3 high, contains component identification information |
|
3E8h |
R |
DMA component parameters register 2 low, contains component identification information |
|
3ECh |
R |
DMA component parameters register 2 high, contains component identification information |
|
3F0h |
R |
DMA component parameters register 1 low, contains component identification information |
|
3F4h |
R |
DMA component parameters register 1 high, contains component identification information |
|
3F8h |
R |
DMA component ID register low, identifies the DMA controller release date |
|
3FCh |
R |
DMA component ID register high, identifies the DMA controller rtl version |
REG_SAR0
Name: Channel 0 Source Address Register
Size: 32
Address offset: 000h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR0 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR0
Name: The read back value is channel 0 source reading address at present
Size: 32
Address offset: 004h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR0 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR0
Name: Channel 0 Destination Address Register
Size: 32
Address offset: 008h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR0 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR0
Name: The read back value is channel 0 destination writing address at present
Size: 32
Address offset: 00Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR0 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP0_L
Name: Channel 0 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 010h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP0_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL0_L
Name: Channel 0 low-32 bits Control Register
Size: 32
Address offset: 018h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL0_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL0_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL0_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL0_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL0_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL0_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL0_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL0_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL0_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL0_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL0_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL0_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL0_H
Name: Channel 0 high-32 bits Control Register
Size: 32
Address offset: 01Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL0_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG0_L
Name: Channel 0 low-32 bits Configuration Register
Size: 32
Address offset: 040h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG0_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG0_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG0_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG0_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG0_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG0_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG0_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG0_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG0_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG0_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG0_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG0_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG0_H
Name: Channel 0 high-32 bits Configuration Register
Size: 32
Address offset: 044h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG0_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG0_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG0_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG0_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG0_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG0_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR0_L
Name: Channel 0 low-32 bits Source Gather Register
Size: 32
Address offset: 048h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR0_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR0_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR0_H
Name: Channel 0 high-32 bits Source Gather Register
Size: 32
Address offset: 04Ch
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR0_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR0_L
Name: Channel 0 low-32 bits Destination Scatter Register
Size: 32
Address offset: 050h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR0_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR0_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR0_H
Name: Channel 0 high-32 bits Destination Scatter Register
Size: 32
Address offset: 054h
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR0_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR1
Name: Channel 1 Source Address Register
Size: 32
Address offset: 058h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR1 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR1
Name: The read back value is channel 1 source reading address at present
Size: 32
Address offset: 05Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR1 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR1
Name: Channel 1 Destination Address Register
Size: 32
Address offset: 060h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR1 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR1
Name: The read back value is channel 1 destination writing address at present
Size: 32
Address offset: 064h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR1 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP1_L
Name: Channel 1 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 068h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP1_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL1_L
Name: Channel 1 low-32 bits Control Register
Size: 32
Address offset: 070h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL1_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL1_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL1_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL1_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL1_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL1_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL1_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL1_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL1_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL1_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL1_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL1_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL1_H
Name: Channel 1 high-32 bits Control Register
Size: 32
Address offset: 074h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL1_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG1_L
Name: Channel 1 low-32 bits Configuration Register
Size: 32
Address offset: 098h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG1_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG1_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG1_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG1_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG1_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG1_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG1_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG1_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG1_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG1_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG1_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG1_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG1_H
Name: Channel 1 high-32 bits Configuration Register
Size: 32
Address offset: 09Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG1_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG1_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG1_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG1_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG1_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG1_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR1_L
Name: Channel 1 low-32 bits Source Gather Register
Size: 32
Address offset: 0A0h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR1_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR1_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR1_H
Name: Channel 1 high-32 bits Source Gather Register
Size: 32
Address offset: 0A4h
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR1_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR1_L
Name: Channel 1 low-32 bits Destination Scatter Register
Size: 32
Address offset: 0A8h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR1_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR1_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR1_H
Name: Channel 1 high-32 bits Destination Scatter Register
Size: 32
Address offset: 0ACh
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR1_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR2
Name: Channel 2 Source Address Register
Size: 32
Address offset: 0B0h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR2 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR2
Name: The read back value is channel 2 source reading address at present
Size: 32
Address offset: 0B4h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR2 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR2
Name: Channel 2 Destination Address Register
Size: 32
Address offset: 0B8h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR2 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR2
Name: The read back value is channel 2 destination writing address at present
Size: 32
Address offset: 0BCh
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR2 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP2_L
Name: Channel 2 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 0C0h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP2_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL2_L
Name: Channel 2 low-32 bits Control Register
Size: 32
Address offset: 0C8h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL2_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL2_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL2_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL2_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL2_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL2_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL2_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL2_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL2_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL2_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL2_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL2_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL2_H
Name: Channel 2 high-32 bits Control Register
Size: 32
Address offset: 0CCh
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL2_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG2_L
Name: Channel 2 low-32 bits Configuration Register
Size: 32
Address offset: 0F0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG2_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG2_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG2_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG2_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG2_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG2_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG2_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG2_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG2_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG2_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG2_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG2_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG2_H
Name: Channel 2 high-32 bits Configuration Register
Size: 32
Address offset: 0F4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG2_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG2_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG2_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG2_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG2_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG2_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR2_L
Name: Channel 2 low-32 bits Source Gather Register
Size: 32
Address offset: 0F8h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR2_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR2_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR2_H
Name: Channel 2 high-32 bits Source Gather Register
Size: 32
Address offset: 0FCh
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR2_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR2_L
Name: Channel 2 low-32 bits Destination Scatter Register
Size: 32
Address offset: 100h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR2_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR2_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR2_H
Name: Channel 2 high-32 bits Destination Scatter Register
Size: 32
Address offset: 104h
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR2_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR3
Name: Channel 3 Source Address Register
Size: 32
Address offset: 108h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR3 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR3
Name: The read back value is channel 3 source reading address at present
Size: 32
Address offset: 10Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR3 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR3
Name: Channel 3 Destination Address Register
Size: 32
Address offset: 110h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR3 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR3
Name: The read back value is channel 3 destination writing address at present
Size: 32
Address offset: 114h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR3 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP3_L
Name: Channel 3 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 118h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP3_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL3_L
Name: Channel 3 low-32 bits Control Register
Size: 32
Address offset: 120h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL3_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL3_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL3_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL3_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL3_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL3_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL3_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL3_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL3_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL3_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL3_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL3_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL3_H
Name: Channel 3 high-32 bits Control Register
Size: 32
Address offset: 124h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL3_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG3_L
Name: Channel 3 low-32 bits Configuration Register
Size: 32
Address offset: 148h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG3_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG3_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG3_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG3_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG3_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG3_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG3_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG3_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG3_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG3_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG3_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG3_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG3_H
Name: Channel 3 high-32 bits Configuration Register
Size: 32
Address offset: 14Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG3_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG3_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG3_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG3_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG3_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG3_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR3_L
Name: Channel 3 low-32 bits Source Gather Register
Size: 32
Address offset: 150h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR3_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR3_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR3_H
Name: Channel 3 high-32 bits Source Gather Register
Size: 32
Address offset: 154h
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR3_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR3_L
Name: Channel 3 low-32 bits Destination Scatter Register
Size: 32
Address offset: 158h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR3_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR3_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR3_H
Name: Channel 3 high-32 bits Destination Scatter Register
Size: 32
Address offset: 15Ch
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR3_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR4
Name: Channel 4 Source Address Register
Size: 32
Address offset: 160h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR4 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR4
Name: The read back value is channel 4 source reading address at present
Size: 32
Address offset: 164h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR4 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR4
Name: Channel 4 Destination Address Register
Size: 32
Address offset: 168h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR4 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR4
Name: The read back value is channel 4 destination writing address at present
Size: 32
Address offset: 16Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR4 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP4_L
Name: Channel 4 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 170h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP4_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL4_L
Name: Channel 4 low-32 bits Control Register
Size: 32
Address offset: 178h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL4_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL4_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL4_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL4_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL4_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL4_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL4_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL4_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL4_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL4_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL4_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL4_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL4_H
Name: Channel 4 high-32 bits Control Register
Size: 32
Address offset: 17Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL4_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG4_L
Name: Channel 4 low-32 bits Configuration Register
Size: 32
Address offset: 1A0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG4_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG4_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG4_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG4_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG4_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG4_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG4_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG4_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG4_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG4_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG4_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG4_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG4_H
Name: Channel 4 high-32 bits Configuration Register
Size: 32
Address offset: 1A4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG4_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG4_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG4_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG4_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG4_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG4_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR4_L
Name: Channel 4 low-32 bits Source Gather Register
Size: 32
Address offset: 1A8h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR4_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR4_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR4_H
Name: Channel 4 high-32 bits Source Gather Register
Size: 32
Address offset: 1ACh
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR4_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR4_L
Name: Channel 4 low-32 bits Destination Scatter Register
Size: 32
Address offset: 1B0h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR4_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR4_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR4_H
Name: Channel 4 high-32 bits Destination Scatter Register
Size: 32
Address offset: 1B4h
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR4_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR5
Name: Channel 5 Source Address Register
Size: 32
Address offset: 1B8h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR5 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR5
Name: The read back value is channel 5 source reading address at present
Size: 32
Address offset: 1BCh
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR5 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR5
Name: Channel 5 Destination Address Register
Size: 32
Address offset: 1C0h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR5 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR5
Name: The read back value is channel 5 destination writing address at present
Size: 32
Address offset: 1C4h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR5 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP5_L
Name: Channel 5 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 1C8h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP5_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL5_L
Name: Channel 5 low-32 bits Control Register
Size: 32
Address offset: 1D0h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL5_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL5_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL5_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL5_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL5_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL5_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL5_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL5_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL5_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL5_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL5_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL5_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL5_H
Name: Channel 5 high-32 bits Control Register
Size: 32
Address offset: 1D4h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL5_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG5_L
Name: Channel 5 low-32 bits Configuration Register
Size: 32
Address offset: 1F8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG5_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG5_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG5_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG5_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG5_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG5_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG5_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG5_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG5_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG5_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG5_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG5_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG5_H
Name: Channel 5 high-32 bits Configuration Register
Size: 32
Address offset: 1FCh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG5_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG5_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG5_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG5_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG5_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG5_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR5_L
Name: Channel 5 low-32 bits Source Gather Register
Size: 32
Address offset: 200h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR5_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR5_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR5_H
Name: Channel 5 high-32 bits Source Gather Register
Size: 32
Address offset: 204h
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR5_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR5_L
Name: Channel 5 low-32 bits Destination Scatter Register
Size: 32
Address offset: 208h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR5_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR5_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR5_H
Name: Channel 5 high-32 bits Destination Scatter Register
Size: 32
Address offset: 20Ch
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR5_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR6
Name: Channel 6 Source Address Register
Size: 32
Address offset: 210h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR6 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR6
Name: The read back value is channel 6 source reading address at present
Size: 32
Address offset: 214h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR6 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR6
Name: Channel 6 Destination Address Register
Size: 32
Address offset: 218h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR6 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR6
Name: The read back value is channel 6 destination writing address at present
Size: 32
Address offset: 21Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR6 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP6_L
Name: Channel 6 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 220h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP6_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL6_L
Name: Channel 6 low-32 bits Control Register
Size: 32
Address offset: 228h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL6_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL6_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL6_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL6_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL6_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL6_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL6_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL6_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL6_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL6_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL6_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL6_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL6_H
Name: Channel 6 high-32 bits Control Register
Size: 32
Address offset: 22Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL6_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG6_L
Name: Channel 6 low-32 bits Configuration Register
Size: 32
Address offset: 250h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG6_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG6_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG6_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG6_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG6_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG6_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG6_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG6_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG6_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG6_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG6_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG6_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG6_H
Name: Channel 6 high-32 bits Configuration Register
Size: 32
Address offset: 254h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG6_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG6_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG6_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG6_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG6_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG6_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR6_L
Name: Channel 6 low-32 bits Source Gather Register
Size: 32
Address offset: 258h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR6_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR6_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR6_H
Name: Channel 6 high-32 bits Source Gather Register
Size: 32
Address offset: 25Ch
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR6_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR6_L
Name: Channel 6 low-32 bits Destination Scatter Register
Size: 32
Address offset: 260h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR6_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR6_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR6_H
Name: Channel 6 high-32 bits Destination Scatter Register
Size: 32
Address offset: 264h
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR6_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR7
Name: Channel 7 Source Address Register
Size: 32
Address offset: 268h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR7 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR7
Name: The read back value is channel 7 source reading address at present
Size: 32
Address offset: 26Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR7 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR7
Name: Channel 7 Destination Address Register
Size: 32
Address offset: 270h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR7 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR7
Name: The read back value is channel 7 destination writing address at present
Size: 32
Address offset: 274h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR7 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP7_L
Name: Channel 7 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 278h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP7_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL7_L
Name: Channel 7 low-32 bits Control Register
Size: 32
Address offset: 280h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL7_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL7_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL7_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL7_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL7_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL7_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL7_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL7_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL7_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL7_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL7_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL7_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL7_H
Name: Channel 7 high-32 bits Control Register
Size: 32
Address offset: 284h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL7_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG7_L
Name: Channel 7 low-32 bits Configuration Register
Size: 32
Address offset: 2A8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG7_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG7_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG7_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG7_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG7_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG7_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG7_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG7_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG7_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG7_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG7_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG7_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG7_H
Name: Channel 7 high-32 bits Configuration Register
Size: 32
Address offset: 2ACh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG7_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG7_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG7_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG7_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG7_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG7_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR7_L
Name: Channel 7 low-32 bits Source Gather Register
Size: 32
Address offset: 2B0h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR7_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR7_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR7_H
Name: Channel 7 high-32 bits Source Gather Register
Size: 32
Address offset: 2B4h
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR7_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR7_L
Name: Channel 7 low-32 bits Destination Scatter Register
Size: 32
Address offset: 2B8h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR7_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR7_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR7_H
Name: Channel 7 high-32 bits Destination Scatter Register
Size: 32
Address offset: 2BCh
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR7_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_RAWTFR_L
Name: Raw Status for IntTfr Interrupt
Size: 32
Address offset: 2C0h
Read/write access: R
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWTFR_L_RAW_TFR |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWBLOCK_L
Name: Raw Status for IntBlock Interrupt
Size: 32
Address offset: 2C8h
Read/write access: R
Raw block transfer complete interrupt status register, shows unmasked block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWBLOCK_L_RAW_BLOCK |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWERR_L
Name: Raw Status for IntErr Interrupt(protocol error)
Size: 32
Address offset: 2E0h
Read/write access: R
Raw error interrupt status register low, shows unmasked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_L_RAW_ERR |
R |
0x0 |
Raw interrupt status for chn0-chn15. (Protocol error) |
REG_RAWERR_H
Name: Raw Status for non-secure access secure register error if defined
Size: 32
Address offset: 2E4h
Read/write access: R
Raw error interrupt status register high, shows unmasked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_H_RAW_ERR |
R |
0x0 |
Raw interrupt status. (Non-secure access secure register error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_STATUSTFR_L
Name: Status for IntTfr Interrupt
Size: 32
Address offset: 2E8h
Read/write access: R
Transfer complete interrupt status register, shows masked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSTFR_L_STATUS_TFR |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSBLOCK_L
Name: Status for IntBlock Interrupt
Size: 32
Address offset: 2F0h
Read/write access: R
Block transfer complete interrupt status register, shows masked block transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSBLOCK_L_STATUS_BLOCK |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSERR_L
Name: Status for IntErr Interrupt
Size: 32
Address offset: 308h
Read/write access: R
Error interrupt status register low, shows masked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_L_STATUS_ERR |
R |
0x0 |
Interrupt status for chn0-chn15. (Protocol error) |
REG_STATUSERR_H
Name: Status for non-secure access secure register error if defined
Size: 32
Address offset: 30Ch
Read/write access: R
Error interrupt status register high, shows masked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_H_STATUS_ERR |
R |
0x0 |
Interrupt status. (Non-secure access secure register error, Sec Error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_MASKTFR_L
Name: Mask for IntTfr Interrupt (chn0-7)
Size: 32
Address offset: 310h
Read/write access: R/W
Transfer complete interrupt mask register, enables or disables transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKTFR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKTFR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKBLOCK_L
Name: Mask for IntBlock Interrupt
Size: 32
Address offset: 318h
Read/write access: R/W
Block transfer complete interrupt mask register, enables or disables block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKBLOCK_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKBLOCK_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_L
Name: Mask for IntErr Interrupt
Size: 32
Address offset: 330h
Read/write access: R/W
Error interrupt mask register low, enables or disables protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKERR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_H
Name: Mask for non-secure access secure register error if defined
Size: 32
Address offset: 334h
Read/write access: R/W
Error interrupt mask register high, enables or disables secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_H_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled These bits only exist when DMAC_ SECURE_MODE has beed defined |
7:0 |
MASKERR_H_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked These bits only exist when DMAC_ SECURE_MODE has beed defined |
REG_CLEARTFR_L
Name: Clear for IntTfr Interrupt
Size: 32
Address offset: 338h
Read/write access: R/W
Transfer complete interrupt clear register, clears transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARTFR_L_CLEAR_TFR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 0 = no effect 1= clear interrupt |
REG_CLEARBLOCK_L
Name: Clear for IntBlock Interrupt
Size: 32
Address offset: 340h
Read/write access: R/W
Block transfer complete interrupt clear register, clears block transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARBLOCK_L_CLEAR_BLOCK |
R/W |
0x0 |
Interrupt clear for chn0-chn15 |
REG_CLEARERR_L
Name: Clear for IntErr Interrupt
Size: 32
Address offset: 358h
Read/write access: R/W
Error interrupt clear register low, clears protocol error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_L_CLEAR_PROTOCOL_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15. (Protocol error) |
REG_CLEARERR_H
Name: Clear for non-secure access secure register error if defined
Size: 32
Address offset: 35Ch
Read/write access: R/W
Error interrupt clear register high, clears secure error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_H_CLEAR_SEC_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 (Non-secure access secure register error, Sec Error) when DMAC_SECURE_MODE has beed defined, else it is reserved; |
REG_STATUSINT_L
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 360h
Read/write access: R
Interrupt status register low, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
STATUSINT_L_ERROR |
R |
0x0 |
OR of the contents of StatusErr register. |
3:2 |
RSVD |
R |
- |
Reserved |
1 |
STATUSINT_L_BLOCK |
R |
0x0 |
OR of the contents of StatusBlock register. |
0 |
STATUSINT_L_TFR |
R |
0x0 |
OR of the contents of StatusTfr register. |
REG_STATUSINT_H
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 364h
Read/write access: R
Interrupt status register high, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_DMACFGREG_L
Name: DMA low-32 bits Configuration Register
Size: 32
Address offset: 398h
Read/write access: R/W
DMA configuration register, configures global DMA controller settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
DMACFGREG_L_DMA_EN |
R/W |
0x1 |
RTK_DMAC Enable bit. 0 = RTK_DMAC Disabled 1 = RTK_DMAC Enabled |
REG_CHENREG_L_1
Name: DMA low-32 bits Channel Enable Register if configed chn number is less than or equal to 8
Size: 32
Address offset: 3A0h
Read/write access: R/W
Channel enable register, enables or disables DMA channels
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
CHENREG_L_1_CH_EN_WE |
R/W |
0x0 |
Channel enable write enable. |
7:0 |
CHENREG_L_1_CH_EN |
R/W |
0x0 |
Enables/Disables the channel. Setting this bit enables a channel; clearing this bit disables the channel. 0 = Disable the Channel 1 = Enable the Channel The CHENREG_L.CH_EN bit is automatically cleared by hardware to disable the channel after the last AXI transfer of the DMA transfer to the destination has completed. Software can therefore poll this bit to determine when this channel is free for a new DMA transfer. |
REG_DMAIDREG_L
Name: DMA low-32 bits ID Register
Size: 32
Address offset: 3A8h
Read/write access: R
DMA ID register, Hardcoded RTK_DMAC peripheral ID
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMAIDREG_L_DMA_ID |
R |
32'h20240513 |
Hardcoded RTK_DMAC Peripheral ID |
REG_DMA_COMP_PARAMS_6_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3C8h
Read/write access: R
DMA component parameters register 6 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH7_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH7_MAX_BLK_SIZE from config_form.vh CH7_MAX_BLK_SIZE = log2(DMAC_CH7_MAX_BLK_SIZE) + 1 |
23:16 |
CH6_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH6_MAX_BLK_SIZE from config_form.vh CH6_MAX_BLK_SIZE = log2(DMAC_CH6_MAX_BLK_SIZE) + 1 |
15:8 |
CH5_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH5_MAX_BLK_SIZE from config_form.vh CH5_MAX_BLK_SIZE = log2(DMAC_CH5_MAX_BLK_SIZE) + 1 |
7:0 |
CH4_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH4_MAX_BLK_SIZE from config_form.vh CH4_MAX_BLK_SIZE = log2(DMAC_CH4_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_6_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3CCh
Read/write access: R
DMA component parameters register 6 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH7_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH7_FIFO_DEPTH parameter. Default value is 0x0. CH7_FIFO_DEPTH = log2(DMAC_CH7_FIFO_DEPTH/8) 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH7_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_MULT_SIZE parameter. Maxium burst transaction size. CH7_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH7_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH7_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH7_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH7_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH7_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH7_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH7_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH7_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH7_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH7_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH7_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D0h
Read/write access: R
DMA component parameters register 5 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH6_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH6_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH6_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_MULT_SIZE parameter. Maxium burst transaction size. CH6_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH6_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH6_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH6_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH6_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH6_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH6_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH6_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH6_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH6_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH6_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH6_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH6_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D4h
Read/write access: R
DMA component parameters register 5 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH5_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH5_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH5_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_MULT_SIZE parameter. Maxium burst transaction size. CH5_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH5_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH5_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH5_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH5_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH5_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH5_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH5_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH5_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH5_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH5_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH5_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH5_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D8h
Read/write access: R
DMA component parameters register 4 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH4_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH4_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH4_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_MULT_SIZE parameter. Maxium burst transaction size. CH4_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH4_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH4_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH4_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH4_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH4_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH4_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH4_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112.0x0 = FALSE 0x1 = TRUE |
8 |
CH4_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH4_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH4_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH4_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH4_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3DCh
Read/write access: R
DMA component parameters register 4 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH3_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH3_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH3_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_MULT_SIZE parameter. Maxium burst transaction size. CH3_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH3_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH3_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH3_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH3_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH3_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH3_SRC_GAT_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH3_DST_SCA_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH3_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH3_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH3_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH3_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E0h
Read/write access: R
DMA component parameters register 3 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH2_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH2_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH2_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_MULT_SIZE parameter. Maxium burst transaction size. CH2_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH2_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH2_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH2_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH2_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH2_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH2_SRC_GAT_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH2_DST_SCA_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH2_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH2_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH2_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH2_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E4h
Read/write access: R
DMA component parameters register 3 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH1_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH1_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH1_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_MULT_SIZE parameter. Maxium burst transaction size. CH1_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH1_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH1_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH1_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH1_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH1_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH1_SRC_GAT_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH1_DST_SCA_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH1_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH1_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH1_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH1_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E8h
Read/write access: R
DMA component parameters register 2 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH0_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH0_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH0_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_MULT_SIZE parameter. Maxium burst transaction size. CH0_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH0_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH0_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH0_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH0_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH0_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH0_SRC_GAT_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH0_DST_SCA_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH0_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH0_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH0_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH0_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3ECh
Read/write access: R
DMA component parameters register 2 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:28 |
CH7_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
27:24 |
CH6_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
23:20 |
CH5_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
19:16 |
CH4_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
15:12 |
CH3_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
11:8 |
CH2_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
7:4 |
CH1_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
3:0 |
CH0_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
REG_DMA_COMP_PARAMS_1_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F0h
Read/write access: R
DMA component parameters register 1 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH3_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH3_MAX_BLK_SIZE from config_form.vh CH3_MAX_BLK_SIZE = log2(DMAC_CH3_MAX_BLK_SIZE) + 1 |
23:16 |
CH2_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH2_MAX_BLK_SIZE from config_form.vh CH2_MAX_BLK_SIZE = log2(DMAC_CH2_MAX_BLK_SIZE) + 1 |
15:8 |
CH1_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH1_MAX_BLK_SIZE from config_form.vh CH1_MAX_BLK_SIZE = log2(DMAC_CH1_MAX_BLK_SIZE) + 1 |
7:0 |
CH0_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH0_MAX_BLK_SIZE from config_form.vh CH0_MAX_BLK_SIZE = log2(DMAC_CH0_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_1_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F4h
Read/write access: R
DMA component parameters register 1 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
HIGH_BIT_NUM_HS_INT3 |
R |
0x0 |
Number of hardware handshake interfaces. If it is 128, this bit read value is 1. |
30 |
HIGH_BIT_NUM_HS_INT2 |
R |
0x0 |
Number of hardware handshake interfaces. If it is greater than 63 and less than 128, this bit read value is 1. |
29 |
HIGH_BIT_NUM_HS_INT1 |
R |
0x0 |
Number of hardware handshake interfaces. If it is greater than 31 and less than 64, this bit read value is 1. |
28 |
STATIC_ENDIAN_SELECT |
R |
0 |
The value of this register is derived from the DMAC_STATIC_ENDIAN_SELECT parameter. 0 = FALSE (dynamic endian fixed) 1 = TRUE (not supported) |
27 |
ADD_ENCODED_PARAMS |
R |
1 |
The value of this register is derived from the DMAC_ADD_ENCODED_PARAMS parameter. 0 = FALSE 1 = TRUE |
26:22 |
NUM_HS_INT |
R |
0x1E |
Number of hardware handshake interfaces. The value of this register is derived from the DMAC_NUM_HS_INT parameter. NUM_HAS_INT = DMAC_NUM_HS_INT[4:0] 0x00 = 0 … 0x10 = 16 |
21:18 |
RSVD |
R |
- |
Reserved |
17:16 |
M2_DATA_WIDTH |
R |
0x0 |
AXI Master2 data width. The value of this register is derived from the DMAC_M2_DATA_WIDTH parameter. Master2 data width should be equal to that of Master 1. M2_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
15:14 |
M1_DATA_WIDTH |
R |
0x0 |
AXI Master1 data width. The value of this register is derived from the DMAC_M1_DATA_WIDTH parameter. Master1 data width should be equal to that of Master 2. M1_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
13:12 |
S_DATA_WIDTH |
R |
0x0 |
APB slave interface data width.The value of this register is derived from the DMAC_S_DATA_WIDTH parameter. The width is fixed to 32 bits for now. S_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = Reserved 0x2 = Reserved 0x3 = Reserved |
11:10 |
NUM_MASTER_INT |
R |
0x1 |
Number of master interface. The value of this register is derived from the DMAC_NUM_MASTER_INT parameter. This value is fixed to 1 (only 2 AXI masters supported now.) 0x0 = Reserved 0x1 = 2 0x2 = Reserved 0x3 = Reserved |
9:6 |
NUM_CHANNELS |
R |
0x7 |
Number of channels. The value of this register is derived from the DMAC_NUM_CHASNNELS parameter. NUM_CHANNELS = DMAC_NUM_CHASNNELS -1 0x0 = 1 … 0xf = 16 |
5:2 |
RSVD |
R |
- |
Reserved |
1:0 |
INTR_IO |
R |
0x0 |
Interrupt output format.The value of this register is derived from the DMAC_INTR_IO parameter. 0x0 = ALL 0x1 = TYPE 0x2 = COMBINED 0x3 = reserved |
REG_DMA_COMPONENT_ID_REGS_L
Name: DMAC ID
Size: 32
Address offset: 3F8h
Read/write access: R
DMA component ID register low, identifies the DMA controller release date
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMA_COMPONENT_ID |
R |
32'h20240513 |
DMAC ID (release_date_. Configure it in config form. |
REG_DMA_COMPONENT_ID_REGS_H
Name: It is obtained from the high 32 bits from git logs in git server.
Size: 32
Address offset: 3FCh
Read/write access: R
DMA component ID register high, identifies the DMA controller rtl version
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RTL_GIT_VER |
R |
32'h482f5d83 |
It is obtained from the high 32 bits from git logs in git server. |
Base Address:
GDMA0_REG : 0x401C0000
AES_SHA_DMA_REG : 0x41002000
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
004h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
008h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
00Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
010h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
018h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
01Ch |
R |
Control register high for DMA channel x for block size |
|
040h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
044h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
048h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
04Ch |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
050h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
054h |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
058h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
05Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
060h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
064h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
068h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
070h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
074h |
R |
Control register high for DMA channel x for block size |
|
098h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
09Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
0A0h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
0A4h |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
0A8h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
0ACh |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
0B0h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
0B4h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
0B8h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
0BCh |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
0C0h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
0C8h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
0CCh |
R |
Control register high for DMA channel x for block size |
|
0F0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
0F4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
0F8h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
0FCh |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
100h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
104h |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
108h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
10Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
110h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
114h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
118h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
120h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
124h |
R |
Control register high for DMA channel x for block size |
|
148h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
14Ch |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
150h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
154h |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
158h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
15Ch |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
160h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
164h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
168h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
16Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
170h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
178h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
17Ch |
R |
Control register high for DMA channel x for block size |
|
1A0h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1A4h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
1A8h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
1ACh |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
1B0h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
1B4h |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
1B8h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
1BCh |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
1C0h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
1C4h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
1C8h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
1D0h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
1D4h |
R |
Control register high for DMA channel x for block size |
|
1F8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
1FCh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
200h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
204h |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
208h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
20Ch |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
210h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
214h |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
218h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
21Ch |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
220h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
228h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
22Ch |
R |
Control register high for DMA channel x for block size |
|
250h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
254h |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
258h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
25Ch |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
260h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
264h |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
268h |
R/W |
Source address register for DMA channel x, specifies the source memory address |
|
26Ch |
R |
Current source address register for DMA channel x, indicates the current source address during transfer |
|
270h |
R/W |
Destination address register for DMA channel x, specifies the destination memory address |
|
274h |
R |
Current destination address register for DMA channel x, indicates the current destination address during transfer |
|
278h |
R/W |
Linked list pointer register low for DMA channel x, points to the starting address of linked list item |
|
280h |
R/W |
Control register low for DMA channel x, configures channel control settings |
|
284h |
R |
Control register high for DMA channel x for block size |
|
2A8h |
R/W |
Configuration register low for DMA channel x, configures transfer parameters |
|
2ACh |
R/W |
Configuration register high for DMA channel x, configures additional transfer parameters |
|
2B0h |
R/W |
Source gather register low for DMA channel x, configures source address increment pattern |
|
2B4h |
R |
Source gather register high for DMA channel x, read-only status of source gather settings |
|
2B8h |
R/W |
Destination scatter register low for DMA channel x, configures destination address increment pattern |
|
2BCh |
R |
Destination scatter register high for DMA channel x, read-only status of destination scatter settings |
|
2C0h |
R |
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts |
|
2C8h |
R |
Raw block transfer complete interrupt status register, shows unmasked block transfer complete interrupts |
|
2E0h |
R |
Raw error interrupt status register low, shows unmasked protocol error interrupts |
|
2E4h |
R |
Raw error interrupt status register high, shows unmasked secure error interrupts |
|
2E8h |
R |
Transfer complete interrupt status register, shows masked transfer complete interrupts |
|
2F0h |
R |
Block transfer complete interrupt status register, shows masked block transfer complete interrupts |
|
308h |
R |
Error interrupt status register low, shows masked protocol error interrupts |
|
30Ch |
R |
Error interrupt status register high, shows masked secure error interrupts |
|
310h |
R/W |
Transfer complete interrupt mask register, enables or disables transfer complete interrupts |
|
318h |
R/W |
Block transfer complete interrupt mask register, enables or disables block transfer complete interrupts |
|
330h |
R/W |
Error interrupt mask register low, enables or disables protocol error interrupts |
|
334h |
R/W |
Error interrupt mask register high, enables or disables secure error interrupts |
|
338h |
R/W |
Transfer complete interrupt clear register, clears transfer complete interrupt status |
|
340h |
R/W |
Block transfer complete interrupt clear register, clears block transfer complete interrupt status |
|
358h |
R/W |
Error interrupt clear register low, clears protocol error interrupt status |
|
35Ch |
R/W |
Error interrupt clear register high, clears secure error interrupt status |
|
360h |
R |
Interrupt status register low, shows combined interrupt status |
|
364h |
R |
Interrupt status register high, shows combined interrupt status |
|
398h |
R/W |
DMA configuration register, configures global DMA controller settings |
|
3A0h |
R/W |
Channel enable register, enables or disables DMA channels |
|
3A8h |
R |
DMA ID register, Hardcoded RTK_DMAC peripheral ID |
|
3C8h |
R |
DMA component parameters register 6 low, contains component identification information |
|
3CCh |
R |
DMA component parameters register 6 high, contains component identification information |
|
3D0h |
R |
DMA component parameters register 5 low, contains component identification information |
|
3D4h |
R |
DMA component parameters register 5 high, contains component identification information |
|
3D8h |
R |
DMA component parameters register 4 low, contains component identification information |
|
3DCh |
R |
DMA component parameters register 4 high, contains component identification information |
|
3E0h |
R |
DMA component parameters register 3 low, contains component identification information |
|
3E4h |
R |
DMA component parameters register 3 high, contains component identification information |
|
3E8h |
R |
DMA component parameters register 2 low, contains component identification information |
|
3ECh |
R |
DMA component parameters register 2 high, contains component identification information |
|
3F0h |
R |
DMA component parameters register 1 low, contains component identification information |
|
3F4h |
R |
DMA component parameters register 1 high, contains component identification information |
|
3F8h |
R |
DMA component ID register low, identifies the DMA controller release date |
|
3FCh |
R |
DMA component ID register high, identifies the DMA controller rtl version |
REG_SAR0
Name: Channel 0 Source Address Register
Size: 32
Address offset: 000h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR0 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR0
Name: The read back value is channel 0 source reading address at present
Size: 32
Address offset: 004h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR0 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR0
Name: Channel 0 Destination Address Register
Size: 32
Address offset: 008h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR0 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR0
Name: The read back value is channel 0 destination writing address at present
Size: 32
Address offset: 00Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR0 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP0_L
Name: Channel 0 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 010h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP0_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL0_L
Name: Channel 0 low-32 bits Control Register
Size: 32
Address offset: 018h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL0_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL0_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL0_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL0_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL0_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL0_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL0_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL0_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL0_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL0_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL0_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL0_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL0_H
Name: Channel 0 high-32 bits Control Register
Size: 32
Address offset: 01Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL0_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG0_L
Name: Channel 0 low-32 bits Configuration Register
Size: 32
Address offset: 040h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG0_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG0_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG0_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG0_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG0_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG0_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG0_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG0_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG0_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG0_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG0_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG0_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG0_H
Name: Channel 0 high-32 bits Configuration Register
Size: 32
Address offset: 044h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG0_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG0_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG0_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG0_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG0_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG0_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR0_L
Name: Channel 0 low-32 bits Source Gather Register
Size: 32
Address offset: 048h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR0_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR0_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR0_H
Name: Channel 0 high-32 bits Source Gather Register
Size: 32
Address offset: 04Ch
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR0_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR0_L
Name: Channel 0 low-32 bits Destination Scatter Register
Size: 32
Address offset: 050h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR0_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR0_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR0_H
Name: Channel 0 high-32 bits Destination Scatter Register
Size: 32
Address offset: 054h
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR0_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR1
Name: Channel 1 Source Address Register
Size: 32
Address offset: 058h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR1 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR1
Name: The read back value is channel 1 source reading address at present
Size: 32
Address offset: 05Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR1 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR1
Name: Channel 1 Destination Address Register
Size: 32
Address offset: 060h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR1 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR1
Name: The read back value is channel 1 destination writing address at present
Size: 32
Address offset: 064h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR1 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP1_L
Name: Channel 1 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 068h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP1_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL1_L
Name: Channel 1 low-32 bits Control Register
Size: 32
Address offset: 070h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL1_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL1_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL1_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL1_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL1_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL1_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL1_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL1_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL1_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL1_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL1_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL1_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL1_H
Name: Channel 1 high-32 bits Control Register
Size: 32
Address offset: 074h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL1_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG1_L
Name: Channel 1 low-32 bits Configuration Register
Size: 32
Address offset: 098h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG1_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG1_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG1_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG1_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG1_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG1_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG1_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG1_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG1_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG1_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG1_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG1_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG1_H
Name: Channel 1 high-32 bits Configuration Register
Size: 32
Address offset: 09Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG1_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG1_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG1_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG1_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG1_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG1_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR1_L
Name: Channel 1 low-32 bits Source Gather Register
Size: 32
Address offset: 0A0h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR1_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR1_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR1_H
Name: Channel 1 high-32 bits Source Gather Register
Size: 32
Address offset: 0A4h
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR1_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR1_L
Name: Channel 1 low-32 bits Destination Scatter Register
Size: 32
Address offset: 0A8h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR1_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR1_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR1_H
Name: Channel 1 high-32 bits Destination Scatter Register
Size: 32
Address offset: 0ACh
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR1_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR2
Name: Channel 2 Source Address Register
Size: 32
Address offset: 0B0h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR2 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR2
Name: The read back value is channel 2 source reading address at present
Size: 32
Address offset: 0B4h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR2 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR2
Name: Channel 2 Destination Address Register
Size: 32
Address offset: 0B8h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR2 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR2
Name: The read back value is channel 2 destination writing address at present
Size: 32
Address offset: 0BCh
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR2 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP2_L
Name: Channel 2 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 0C0h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP2_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL2_L
Name: Channel 2 low-32 bits Control Register
Size: 32
Address offset: 0C8h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL2_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL2_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL2_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL2_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL2_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL2_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL2_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL2_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL2_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL2_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL2_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL2_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL2_H
Name: Channel 2 high-32 bits Control Register
Size: 32
Address offset: 0CCh
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL2_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG2_L
Name: Channel 2 low-32 bits Configuration Register
Size: 32
Address offset: 0F0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG2_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG2_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG2_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG2_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG2_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG2_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG2_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG2_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG2_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG2_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG2_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG2_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG2_H
Name: Channel 2 high-32 bits Configuration Register
Size: 32
Address offset: 0F4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG2_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG2_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG2_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG2_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG2_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG2_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR2_L
Name: Channel 2 low-32 bits Source Gather Register
Size: 32
Address offset: 0F8h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR2_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR2_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR2_H
Name: Channel 2 high-32 bits Source Gather Register
Size: 32
Address offset: 0FCh
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR2_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR2_L
Name: Channel 2 low-32 bits Destination Scatter Register
Size: 32
Address offset: 100h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR2_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR2_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR2_H
Name: Channel 2 high-32 bits Destination Scatter Register
Size: 32
Address offset: 104h
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR2_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR3
Name: Channel 3 Source Address Register
Size: 32
Address offset: 108h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR3 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR3
Name: The read back value is channel 3 source reading address at present
Size: 32
Address offset: 10Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR3 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR3
Name: Channel 3 Destination Address Register
Size: 32
Address offset: 110h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR3 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR3
Name: The read back value is channel 3 destination writing address at present
Size: 32
Address offset: 114h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR3 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP3_L
Name: Channel 3 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 118h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP3_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL3_L
Name: Channel 3 low-32 bits Control Register
Size: 32
Address offset: 120h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL3_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL3_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL3_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL3_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL3_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL3_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL3_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL3_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL3_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL3_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL3_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL3_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL3_H
Name: Channel 3 high-32 bits Control Register
Size: 32
Address offset: 124h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL3_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG3_L
Name: Channel 3 low-32 bits Configuration Register
Size: 32
Address offset: 148h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG3_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG3_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG3_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG3_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG3_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG3_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG3_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG3_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG3_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG3_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG3_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG3_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG3_H
Name: Channel 3 high-32 bits Configuration Register
Size: 32
Address offset: 14Ch
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG3_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG3_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG3_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG3_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG3_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG3_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR3_L
Name: Channel 3 low-32 bits Source Gather Register
Size: 32
Address offset: 150h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR3_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR3_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR3_H
Name: Channel 3 high-32 bits Source Gather Register
Size: 32
Address offset: 154h
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR3_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR3_L
Name: Channel 3 low-32 bits Destination Scatter Register
Size: 32
Address offset: 158h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR3_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR3_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR3_H
Name: Channel 3 high-32 bits Destination Scatter Register
Size: 32
Address offset: 15Ch
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR3_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR4
Name: Channel 4 Source Address Register
Size: 32
Address offset: 160h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR4 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR4
Name: The read back value is channel 4 source reading address at present
Size: 32
Address offset: 164h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR4 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR4
Name: Channel 4 Destination Address Register
Size: 32
Address offset: 168h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR4 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR4
Name: The read back value is channel 4 destination writing address at present
Size: 32
Address offset: 16Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR4 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP4_L
Name: Channel 4 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 170h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP4_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL4_L
Name: Channel 4 low-32 bits Control Register
Size: 32
Address offset: 178h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL4_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL4_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL4_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL4_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL4_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL4_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL4_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL4_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL4_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL4_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL4_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL4_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL4_H
Name: Channel 4 high-32 bits Control Register
Size: 32
Address offset: 17Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL4_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG4_L
Name: Channel 4 low-32 bits Configuration Register
Size: 32
Address offset: 1A0h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG4_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG4_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG4_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG4_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG4_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG4_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG4_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG4_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG4_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG4_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG4_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG4_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG4_H
Name: Channel 4 high-32 bits Configuration Register
Size: 32
Address offset: 1A4h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG4_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG4_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG4_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG4_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG4_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG4_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR4_L
Name: Channel 4 low-32 bits Source Gather Register
Size: 32
Address offset: 1A8h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR4_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR4_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR4_H
Name: Channel 4 high-32 bits Source Gather Register
Size: 32
Address offset: 1ACh
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR4_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR4_L
Name: Channel 4 low-32 bits Destination Scatter Register
Size: 32
Address offset: 1B0h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR4_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR4_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR4_H
Name: Channel 4 high-32 bits Destination Scatter Register
Size: 32
Address offset: 1B4h
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR4_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR5
Name: Channel 5 Source Address Register
Size: 32
Address offset: 1B8h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR5 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR5
Name: The read back value is channel 5 source reading address at present
Size: 32
Address offset: 1BCh
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR5 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR5
Name: Channel 5 Destination Address Register
Size: 32
Address offset: 1C0h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR5 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR5
Name: The read back value is channel 5 destination writing address at present
Size: 32
Address offset: 1C4h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR5 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP5_L
Name: Channel 5 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 1C8h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP5_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL5_L
Name: Channel 5 low-32 bits Control Register
Size: 32
Address offset: 1D0h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL5_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL5_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL5_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL5_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL5_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL5_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL5_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL5_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL5_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL5_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL5_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL5_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL5_H
Name: Channel 5 high-32 bits Control Register
Size: 32
Address offset: 1D4h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL5_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG5_L
Name: Channel 5 low-32 bits Configuration Register
Size: 32
Address offset: 1F8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG5_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG5_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG5_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG5_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG5_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG5_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG5_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG5_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG5_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG5_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG5_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG5_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG5_H
Name: Channel 5 high-32 bits Configuration Register
Size: 32
Address offset: 1FCh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG5_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG5_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG5_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG5_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG5_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG5_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR5_L
Name: Channel 5 low-32 bits Source Gather Register
Size: 32
Address offset: 200h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR5_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR5_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR5_H
Name: Channel 5 high-32 bits Source Gather Register
Size: 32
Address offset: 204h
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR5_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR5_L
Name: Channel 5 low-32 bits Destination Scatter Register
Size: 32
Address offset: 208h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR5_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR5_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR5_H
Name: Channel 5 high-32 bits Destination Scatter Register
Size: 32
Address offset: 20Ch
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR5_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR6
Name: Channel 6 Source Address Register
Size: 32
Address offset: 210h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR6 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR6
Name: The read back value is channel 6 source reading address at present
Size: 32
Address offset: 214h
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR6 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR6
Name: Channel 6 Destination Address Register
Size: 32
Address offset: 218h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR6 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR6
Name: The read back value is channel 6 destination writing address at present
Size: 32
Address offset: 21Ch
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR6 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP6_L
Name: Channel 6 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 220h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP6_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL6_L
Name: Channel 6 low-32 bits Control Register
Size: 32
Address offset: 228h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL6_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL6_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL6_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL6_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL6_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL6_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL6_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL6_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL6_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL6_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL6_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL6_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL6_H
Name: Channel 6 high-32 bits Control Register
Size: 32
Address offset: 22Ch
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL6_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG6_L
Name: Channel 6 low-32 bits Configuration Register
Size: 32
Address offset: 250h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG6_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG6_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG6_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG6_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG6_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG6_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG6_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG6_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG6_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG6_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG6_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG6_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG6_H
Name: Channel 6 high-32 bits Configuration Register
Size: 32
Address offset: 254h
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG6_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG6_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG6_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG6_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG6_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG6_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR6_L
Name: Channel 6 low-32 bits Source Gather Register
Size: 32
Address offset: 258h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR6_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR6_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR6_H
Name: Channel 6 high-32 bits Source Gather Register
Size: 32
Address offset: 25Ch
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR6_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR6_L
Name: Channel 6 low-32 bits Destination Scatter Register
Size: 32
Address offset: 260h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR6_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR6_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR6_H
Name: Channel 6 high-32 bits Destination Scatter Register
Size: 32
Address offset: 264h
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR6_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_SAR7
Name: Channel 7 Source Address Register
Size: 32
Address offset: 268h
Read/write access: R/W
Source address register for DMA channel x, specifies the source memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
SAR7 |
R/W |
Unknown |
Source Address of DMA transfer.Updated after each source transfer. The SINC field in the CTLx register determines whether the address increments, or is left unchanged on every source transfer throughout the block transfer. |
REG_CURR_SAR7
Name: The read back value is channel 7 source reading address at present
Size: 32
Address offset: 26Ch
Read/write access: R
Current source address register for DMA channel x, indicates the current source address during
transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_SAR7 |
R |
0x0 |
The read back value is source reading address at present |
REG_DAR7
Name: Channel 7 Destination Address Register
Size: 32
Address offset: 270h
Read/write access: R/W
Destination address register for DMA channel x, specifies the destination memory address
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DAR7 |
R/W |
Unknown |
Destination address of DMA transfer.Updated after each destination transfer. The DINC field in the CTLx register determines whether the address increments, or is left unchanged on every destination transfer throughout the block transfer. |
REG_CURR_DAR7
Name: The read back value is channel 7 destination writing address at present
Size: 32
Address offset: 274h
Read/write access: R
Current destination address register for DMA channel x, indicates the current destination address
during transfer
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CURR_DAR7 |
R |
0x0 |
The read back value is destination writing address at present |
REG_LLP7_L
Name: Channel 7 low-32 bits Linked List Pointer Register
Size: 32
Address offset: 278h
Read/write access: R/W
Linked list pointer register low for DMA channel x, points to the starting address of linked list
item
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:2 |
LLP7_L_LOC |
R/W |
Unknown |
Starting Address In Memory of next LLI if block chaining is enabled. Note that the two LSBs of the starting address are not stored because the address is assumed to be aligned to a 32-bit boundary.LLI accesses are always 32-bit accesses aligned to 32-bit boundaries and cannot be changed or programmed to anything other than 32-bit. |
1:0 |
RSVD |
R |
- |
Reserved |
REG_CTL7_L
Name: Channel 7 low-32 bits Control Register
Size: 32
Address offset: 280h
Read/write access: R/W
Control register low for DMA channel x, configures channel control settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:29 |
RSVD |
R |
- |
Reserved |
28 |
CTL7_L_LLP_SRC_EN |
R/W |
0x0 |
Block chanining is enabled on the source side only if the LLP_SRC_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
27 |
CTL7_L_LLP_DST_EN |
R/W |
0x0 |
Block chanining is enabled on the destination side only if the LLP_DST_EN field id high and LLPx_L.LOC is non-zero; for more information,see 7.4.1.1 “Block Chaining Using Linked Lists” Dependencies:This field does not exist if the configuration parameterDMAC_CHx_MULTI_BLK_EN is not selected or if DMAC_CHx_HC_LLP is selected; in this case, the read-back value is always 0. |
26:23 |
RSVD |
R |
- |
Reserved |
22:20 |
CTL7_L_TT_FC |
R/W |
0x0 |
Transfer Type and Flow Control.The following transfer types are supported.
Flow Control can be assigned to the RTK_DMAC, the source peripheral, or the destination peripheral. Table 6-4 lists the decoding for this field. For more information on transfer types and flow control, refer to “Setup/Operation of RTK_DMAC Transfers”. Reset Value: 3’h0 Dependencies: If hardware handshake isn’t support, then TT_FC can only be set to 3’b0. TT_FC[2] can only be read. |
19 |
RSVD |
R |
- |
Reserved |
18 |
CTL7_L_DST_SCATTER_EN |
R/W |
0x0 |
Destination scatter enable bit:0 = Scatter disabled1 = Scatter enabledScatter on the destination side is applicable only when the CTLx_L.DINC bit indicates an incrementing address control and DARx should be aligned with DST_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_DST_SCA_EN is not selected. |
17 |
CTL7_L_SRC_GATHER_EN |
R/W |
0x0 |
Source gather enable bit: 0 = Gather disabled 1 = Gather enabled Gather on the source side is applicable only when the CTLx_L.SINC bit indicates an incrementing address control and SARx should be aligned with SRC_TR_WIDTH. Dependencies: This field does not exist if DMAC_CHx_SRC_GAT_EN is not selected. |
16:14 |
CTL7_L_SRC_MSIZE |
R/W |
0x1 |
Source Burst Transaction Length. Number of data items, each of width CTLx_L.SRC_TR_WIDTH if source is not memory, otherwise each of width DMAC_TR_WIDTH_DEFAULT, to be read from the source every time a source burst transaction request is made from either the corresponding hardware or software handshaking interface. Read burst transaction length on bus (ARLen) will not exceed this value, but may be less than this value. If SINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-0 lists the decoding for this field. |
13:11 |
CTL7_L_DEST_MSIZE |
R/W |
0x1 |
Destination Burst Transaction Length. Number of data items, each of width DATA_WIDTH, to be written to the destination every time a destination burst transaction request is made from either the corresponding hardware or software handshaking interface. Write burst transaction length on bus (AWLen) will not exceed this value, but may be less than this value. If DINC is setted to “no change”, this value should not be greater than 16 to conform to the AXI protocol. If enabled ‘DMAC_CHx_MSIZE_BIGGER_THAN_FIFO_DEPTH’ feature, to improve performance, can set CTLx_L.SRC_MSIZE to a high value to make DMAC send longer burst length command. But to avoid deadlock, if Source slave and Destination slave is the same slave, should not set CTLx_L.SRC_MSIZE over than FIFO_depth; Table 6-2-1 lists the decoding for this field. |
10:9 |
CTL7_L_SINC |
R/W |
0x0 |
Source Address Increment. Indicates whether to increment the source address on every source transfer. If the device is fetching data from a source peripheral FIFO with a fixed address, then set this field to “No change.”If source is memory appointed by CTLx_L.TT_FC, and set SINC=No change, then SRC_TR_WIDTH must be set to BUS width. And DMAC will read data from the fixed memory address until block transfer finish, but It is not recommended to read memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01 =Not support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.SRC_TR_WIDTH boundary. |
8:7 |
CTL7_L_DINC |
R/W |
0x0 |
Destination Address Increment. Indicates whether to increment destination address on every destination transfer. If your device is writing data to a destination peripheral FIFO with a fixed address, then set this field to “No change.”If destination is memory appointed by CTLx_L.TT_FC, and set DINC=No change, then DST_TR_WIDTH must be set to BUS width. And DMAC will write data to the fixed memory address until block transfer finish, but It is not recommended to write memory like this, because some memory controller not support fixed burst transaction and may transform the fixed burst transaction to incremental burst transaction. 00 = Increment 01=Not Support 1x = No change 备注 Incrementing is done for alignment to the next CTLx_L.DST_TR_WIDTH boundary. |
6:4 |
CTL7_L_SRC_TR_WIDTH |
R/W |
0x0 |
Source Transfer Width. Table 6-3 lists the decoding for this field.It can’t be mapped to AXI bus data width directly. Since AXI bus data width is fixed (such as 32bit/64bit), AXI use byte enable signal for byte/half word transfer (still burst). So, the SRC_TR_WIDTH is only used for total block data size calculation and streaming mode byte/half word transfer (for FIFO transfer). 备注 SRC_TR_WIDTH must not be bigger than BUS width. |
3:1 |
CTL7_L_DST_TR_WIDTH |
R/W |
0x0 |
Destination Transfer Width.Table 6-3 lists the decoding for this field. It can’t be mapped to AXI bus data width directly. For a non-memory peripheral, typically the peripheral (destination) FIFO width.Note: DST_TR_WIDTH must not be bigger than BUS width |
0 |
CTL7_L_INT_EN |
R/W |
0x1 |
Interrupt Enable Bit. If set, then all interrupt-generating sources are enabled. Functions as a global mask bit for all interrupts for the channel; raw* interrupt registers still assert if CTLx_L.INT_EN = 0. |
REG_CTL7_H
Name: Channel 7 high-32 bits Control Register
Size: 32
Address offset: 284h
Read/write access: R
Control register high for DMA channel x for block size
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CTL7_H_TRANS_DATA_CNT |
R |
0x0 |
Data Transfered Count.Once the transfer starts, the read-back value is the total number of data bytes already write to destination memory or peripheral. |
REG_CFG7_L
Name: Channel 7 low-32 bits Configuration Register
Size: 32
Address offset: 2A8h
Read/write access: R/W
Configuration register low for DMA channel x, configures transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
CFG7_L_RELOAD_DST |
R/W |
0x0 |
Automatic Destination Reload. The DARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated.This register does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
30 |
CFG7_L_RELOAD_SRC |
R/W |
0x0 |
Automatic Source Reload. The SARx register can be automatically reloaded from its initial value at the end of every block for multi-block transfers. A new block transfer is then initiated. This field does not exist if the configuration parameter DMAC_CHx_MULTI_BLK_EN is not selected; in this case, the read-back value is always 0. |
29:20 |
RSVD |
R |
- |
Reserved |
19 |
CFG7_L_SRC_HS_POL |
R/W |
0x0 |
Source Handshaking Interface Polarity. 0 = Active high 1 = Active low |
18 |
CFG7_L_DST_HS_POL |
R/W |
0x0 |
Destination Handshaking Interface Polarity. 0 = Active high 1 = Active low For information on this, refer to “Handshaking Interface” . |
17:12 |
RSVD |
R |
- |
Reserved |
11 |
CFG7_L_HS_SEL_SRC |
R/W |
0x1 |
Source Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for source requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware-initiated transaction requests are ignored. If the source peripheral is memory, then this bit is ignored. |
10 |
CFG7_L_HS_SEL_DST |
R/W |
0x1 |
Destination Software or Hardware Handshaking Select. This register selects which of the handshaking interfaces – hardware or software – is active for destination requests on this channel. 0 = Hardware handshaking interface. Software-initiated transaction requests are ignored. 1 = Software handshaking interface. Hardware- initiated transaction requests are ignored. If the destination peripheral is memory, then this bit is ignored. |
9 |
CFG7_L_FIFO_EMPTY |
R |
0x1 |
Indicates if there is data left in the channel FIFO. 1 = Channel FIFO empty 0 = Channel FIFO not empty |
8 |
CFG7_L_CH_SUSP |
R/W |
0x0 |
Channel Suspend. Suspends all DMA data transfers from the source until this bit is cleared. There is no guarantee that the current transaction will complete. Can also be used in conjunction with CFGx_l.INACTIVE to cleanly disable a channel without losing any data. 0 = Not suspended 1 = Suspend DMA transfer from the source. This field will be reset to 0 after “Disabling a Channel Prior to Transfer Completion” automatically by hardware.For more information, refer to “7.7 Disabling a Channel Prior to Transfer Completion” . 备注 if user not define DMAC_CH*_SUPPORT_SUSPEND, it only can be readed. |
7:4 |
CFG7_L_CH_PRIOR |
R/W |
0x0 |
Channel priority. RTK DMAC supports three kinds of channel priority now, fixed priority, round robin priority and programmable priority. The default way is fixed priority to reduce area, and channel0 has the highest priority, channel15 has the lowest priority. Changing the definition of parameter FIX_PRIORITY or Programmable_PRIORITY can change priority way. If RTK DMAC is configured to support Programmable priority, this field will be used to set priority between channels. CH_PRIOR’s legal value is 0 ~ (DMAC_NUM_CHANNELS-1), and 0 is the highest priority value, (DMAC_NUM_CHANNELS-1) is the lowest priroty value. If more than one channel are set with the same priroty value, the channel with small channel number index has higher priority. If DMAC is configured to support fix priority or round-robin priority, this field is not exist. 备注 if user not define ProgrammablePriority, it only can be readed. |
3 |
RSVD |
R |
- |
Reserved |
2 |
CFG7_L_DST_PCTL_OVER |
R |
0x1 |
DMA destination bus protocol finish, indicating the current write command has finished. |
1 |
CFG7_L_SRC_PCTL_OVER |
R |
0x1 |
DMA Source bus protocol finish, indicating the current read command has finished. |
0 |
CFG7_L_INACTIVE |
R |
0x1 |
Indicates if the channel is inactive. Can be used in conjunction with CFGx_L.CH_SUSP to cleanly disable a channel when destination is peripheral. For more information, refer to “Disabling a Channel Prior to Transfer Completion” . 1 = Channel Inactive for axi interface 0 = Channel not Inactive for axi interface |
REG_CFG7_H
Name: Channel 7 high-32 bits Configuration Register
Size: 32
Address offset: 2ACh
Read/write access: R/W
Configuration register high for DMA channel x, configures additional transfer parameters
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CFG7_H_EXTENDED_DEST_PER1 |
R/W |
0x0 |
The extened 4th bit of DEST_PER when hardware handshake interfaces number is configured to 32. |
15 |
CFG7_H_EXTENDED_SRC_PER1 |
R/W |
0x0 |
The extened 4th bit of SRC_PER when hardware handshake interfaces number is configured to 32. |
14:11 |
CFG7_H_DEST_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the destination of channel x if the FGx.HS_SEL_DST field is 0; otherwise, this field is ignored. The channel can then communicate with the destinationperipheral connected to that interface through the assignedhardware handshaking interface. NOTE1: For correct DMA operation, only one peripheral (sourceor destination) should be assigned to the same handshaking interface NOTE2: This field does not exist if the configuration parameterDMAC_NUM_HS_INT is set to 0. |
10:7 |
CFG7_H_SRC_PER |
R/W |
0x0 |
Assigns a hardware handshaking interface(0 – DMAC_NUM_HS_INT-1) to the source of channel x if the CFGx.HS_SEL_SRC field is 0; otherwise, this field is ignored. The channel can then communicate with the source peripheral connected to that interface through the assigned hardware handshaking interface. NOTE1: For correct RTK_DMAC operation, only one peripheral (source or destination) should be assigned to the same handshaking interface. NOTE2: This field does not exist if the configuration parameter DMAC_NUM_HS_INT is set to 0. |
6:4 |
RSVD |
R |
- |
Reserved |
3 |
CFG7_H_PROTCTL |
R/W |
0x1 |
Protection Control.Set the bit 35 to 0 will enable the channel secure DMA transfer. Set the bit 35 to 1 will enable the channel non-secure DMAC transfer. 备注 if user not define DMAC_SECURE_MODE, it only can be readed. |
2:1 |
RSVD |
R |
- |
Reserved |
0 |
CFG7_H_FCMODE |
R/W |
0x0 |
Flow Control Mode. Determines when source transaction requests are serviced when the Destination Peripheral is the flow controller. 0 = Source transaction requests are servied when they occur. Data pre-fetching is enabled. 1 = Source transaction requests are not serviced until a destination transaction request occurs. Data pre-fetching is disabled. 备注 Please keep this bit 0 when Transfer Type and Flow Control is not ”destination peripheral is the flow controller and transfer type is peripheral to peripheral” (TT_FC!=7). |
REG_SGR7_L
Name: Channel 7 low-32 bits Source Gather Register
Size: 32
Address offset: 2B0h
Read/write access: R/W
Source gather register low for DMA channel x, configures source address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
SGR7_L_SGC |
R/W |
Unknown |
Source gather count. Source contiguous transfer count between successive gather boundaries. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
19:0 |
SGR7_L_SGI |
R/W |
Unknown |
Source gather interval. 备注 if user not define DMAC_SRC_GAT_EN, it only can be readed. |
REG_SGR7_H
Name: Channel 7 high-32 bits Source Gather Register
Size: 32
Address offset: 2B4h
Read/write access: R
Source gather register high for DMA channel x, read-only status of source gather settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
SGR7_H_BLOCK_TS_L |
R |
0x2 |
Low 16-bits of Block Transfer Size.The number programmed into CTLX.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high part. The low 16 bits is stored into SGRx.BLOCK_TS_L while the high part is stored into DSRx.BLOCK_TS_H Width: The width of the single transaction is determined by CTLx.SRC_TR_WIDTH. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_DSR7_L
Name: Channel 7 low-32 bits Destination Scatter Register
Size: 32
Address offset: 2B8h
Read/write access: R/W
Destination scatter register low for DMA channel x, configures destination address increment pattern
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:20 |
DSR7_L_DSC |
R/W |
Unknown |
Destination scatter count. Destination contiguous transfer count between successive scatter boundaries. 备注 if user not define DMAC_DST_SCA_EN, it only can be readed. |
19:0 |
DSR7_L_DSI |
R/W |
Unknown |
Destination scatter interval.Note: if user not define DMAC_DST_SCA_EN, it only can be readed. |
REG_DSR7_H
Name: Channel 7 high-32 bits Destination Scatter Register
Size: 32
Address offset: 2BCh
Read/write access: R
Destination scatter register high for DMA channel x, read-only status of destination scatter
settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:21 |
RSVD |
R |
- |
Reserved |
20:16 |
DSR7_H_BLOCK_TS_H |
R |
0x0 |
High part of Block Transfer SizeThe number programmed into CTLx_H.BLOCK_TS, which indicates the total number of single transactions to perform for every block transfer, is separated into low 16 bits and high 16 bits. The low 16-bits is stored into SGRx_H.BLOCK_TS_LOW while the high 16-bits is stored into DSRx_H.BLOCK_TS_HIGH Width: The width of the single transaction is determined by CTLx_L.SRC_TR_WIDTH.b = log2 (DMAC_CHx_MAX_BLK_SIZE). Dependencies: The maximum value of DMAC_CHx_MAX_BLK_SIZE is 2 ^ (31-log2 (DMAC_DATA_WIDTH/8)) – 1. |
15:0 |
RSVD |
R |
- |
Reserved |
REG_RAWTFR_L
Name: Raw Status for IntTfr Interrupt
Size: 32
Address offset: 2C0h
Read/write access: R
Raw transfer complete interrupt status register, shows unmasked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWTFR_L_RAW_TFR |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWBLOCK_L
Name: Raw Status for IntBlock Interrupt
Size: 32
Address offset: 2C8h
Read/write access: R
Raw block transfer complete interrupt status register, shows unmasked block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWBLOCK_L_RAW_BLOCK |
R |
0x0 |
Raw interrupt status for chn0-chn15 |
REG_RAWERR_L
Name: Raw Status for IntErr Interrupt(protocol error)
Size: 32
Address offset: 2E0h
Read/write access: R
Raw error interrupt status register low, shows unmasked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_L_RAW_ERR |
R |
0x0 |
Raw interrupt status for chn0-chn15. (Protocol error) |
REG_RAWERR_H
Name: Raw Status for non-secure access secure register error if defined
Size: 32
Address offset: 2E4h
Read/write access: R
Raw error interrupt status register high, shows unmasked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
RAWERR_H_RAW_ERR |
R |
0x0 |
Raw interrupt status. (Non-secure access secure register error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_STATUSTFR_L
Name: Status for IntTfr Interrupt
Size: 32
Address offset: 2E8h
Read/write access: R
Transfer complete interrupt status register, shows masked transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSTFR_L_STATUS_TFR |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSBLOCK_L
Name: Status for IntBlock Interrupt
Size: 32
Address offset: 2F0h
Read/write access: R
Block transfer complete interrupt status register, shows masked block transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSBLOCK_L_STATUS_BLOCK |
R |
0x0 |
Interrupt status for chn0-chn15 |
REG_STATUSERR_L
Name: Status for IntErr Interrupt
Size: 32
Address offset: 308h
Read/write access: R
Error interrupt status register low, shows masked protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_L_STATUS_ERR |
R |
0x0 |
Interrupt status for chn0-chn15. (Protocol error) |
REG_STATUSERR_H
Name: Status for non-secure access secure register error if defined
Size: 32
Address offset: 30Ch
Read/write access: R
Error interrupt status register high, shows masked secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
STATUSERR_H_STATUS_ERR |
R |
0x0 |
Interrupt status. (Non-secure access secure register error, Sec Error) if DMAC_SECURE_MODE has been defined; else it is reserved. |
REG_MASKTFR_L
Name: Mask for IntTfr Interrupt (chn0-7)
Size: 32
Address offset: 310h
Read/write access: R/W
Transfer complete interrupt mask register, enables or disables transfer complete interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKTFR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKTFR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKBLOCK_L
Name: Mask for IntBlock Interrupt
Size: 32
Address offset: 318h
Read/write access: R/W
Block transfer complete interrupt mask register, enables or disables block transfer complete
interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKBLOCK_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKBLOCK_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_L
Name: Mask for IntErr Interrupt
Size: 32
Address offset: 330h
Read/write access: R/W
Error interrupt mask register low, enables or disables protocol error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_L_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled |
7:0 |
MASKERR_L_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked |
REG_MASKERR_H
Name: Mask for non-secure access secure register error if defined
Size: 32
Address offset: 334h
Read/write access: R/W
Error interrupt mask register high, enables or disables secure error interrupts
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
MASKERR_H_INT_MASK_WE |
R/W |
0x0 |
Interrupt Mask Write Enable(chn0-chn7) 0 = write disabled 1 = write enabled These bits only exist when DMAC_ SECURE_MODE has beed defined |
7:0 |
MASKERR_H_INT_MASK |
R/W |
0x0 |
Interrupt Mask(chn0-chn7) 0 = masked 1 = unmasked These bits only exist when DMAC_ SECURE_MODE has beed defined |
REG_CLEARTFR_L
Name: Clear for IntTfr Interrupt
Size: 32
Address offset: 338h
Read/write access: R/W
Transfer complete interrupt clear register, clears transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARTFR_L_CLEAR_TFR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 0 = no effect 1= clear interrupt |
REG_CLEARBLOCK_L
Name: Clear for IntBlock Interrupt
Size: 32
Address offset: 340h
Read/write access: R/W
Block transfer complete interrupt clear register, clears block transfer complete interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARBLOCK_L_CLEAR_BLOCK |
R/W |
0x0 |
Interrupt clear for chn0-chn15 |
REG_CLEARERR_L
Name: Clear for IntErr Interrupt
Size: 32
Address offset: 358h
Read/write access: R/W
Error interrupt clear register low, clears protocol error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_L_CLEAR_PROTOCOL_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15. (Protocol error) |
REG_CLEARERR_H
Name: Clear for non-secure access secure register error if defined
Size: 32
Address offset: 35Ch
Read/write access: R/W
Error interrupt clear register high, clears secure error interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:0 |
CLEARERR_H_CLEAR_SEC_ERROR |
R/W |
0x0 |
Interrupt clear for chn0-chn15 (Non-secure access secure register error, Sec Error) when DMAC_SECURE_MODE has beed defined, else it is reserved; |
REG_STATUSINT_L
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 360h
Read/write access: R
Interrupt status register low, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
STATUSINT_L_ERROR |
R |
0x0 |
OR of the contents of StatusErr register. |
3:2 |
RSVD |
R |
- |
Reserved |
1 |
STATUSINT_L_BLOCK |
R |
0x0 |
OR of the contents of StatusBlock register. |
0 |
STATUSINT_L_TFR |
R |
0x0 |
OR of the contents of StatusTfr register. |
REG_STATUSINT_H
Name: Combined Interrupt Sataus Register
Size: 32
Address offset: 364h
Read/write access: R
Interrupt status register high, shows combined interrupt status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RSVD |
R |
- |
Reserved |
REG_DMACFGREG_L
Name: DMA low-32 bits Configuration Register
Size: 32
Address offset: 398h
Read/write access: R/W
DMA configuration register, configures global DMA controller settings
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
DMACFGREG_L_DMA_EN |
R/W |
0x1 |
RTK_DMAC Enable bit. 0 = RTK_DMAC Disabled 1 = RTK_DMAC Enabled |
REG_CHENREG_L_1
Name: DMA low-32 bits Channel Enable Register if configed chn number is less than or equal to 8
Size: 32
Address offset: 3A0h
Read/write access: R/W
Channel enable register, enables or disables DMA channels
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:16 |
RSVD |
R |
- |
Reserved |
15:8 |
CHENREG_L_1_CH_EN_WE |
R/W |
0x0 |
Channel enable write enable. |
7:0 |
CHENREG_L_1_CH_EN |
R/W |
0x0 |
Enables/Disables the channel. Setting this bit enables a channel; clearing this bit disables the channel. 0 = Disable the Channel 1 = Enable the Channel The CHENREG_L.CH_EN bit is automatically cleared by hardware to disable the channel after the last AXI transfer of the DMA transfer to the destination has completed. Software can therefore poll this bit to determine when this channel is free for a new DMA transfer. |
REG_DMAIDREG_L
Name: DMA low-32 bits ID Register
Size: 32
Address offset: 3A8h
Read/write access: R
DMA ID register, Hardcoded RTK_DMAC peripheral ID
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMAIDREG_L_DMA_ID |
R |
32'h20250311 |
Hardcoded RTK_DMAC Peripheral ID |
REG_DMA_COMP_PARAMS_6_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3C8h
Read/write access: R
DMA component parameters register 6 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH7_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH7_MAX_BLK_SIZE from config_form.vh CH7_MAX_BLK_SIZE = log2(DMAC_CH7_MAX_BLK_SIZE) + 1 |
23:16 |
CH6_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH6_MAX_BLK_SIZE from config_form.vh CH6_MAX_BLK_SIZE = log2(DMAC_CH6_MAX_BLK_SIZE) + 1 |
15:8 |
CH5_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH5_MAX_BLK_SIZE from config_form.vh CH5_MAX_BLK_SIZE = log2(DMAC_CH5_MAX_BLK_SIZE) + 1 |
7:0 |
CH4_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH4_MAX_BLK_SIZE from config_form.vh CH4_MAX_BLK_SIZE = log2(DMAC_CH4_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_6_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3CCh
Read/write access: R
DMA component parameters register 6 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH7_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH7_FIFO_DEPTH parameter. Default value is 0x0. CH7_FIFO_DEPTH = log2(DMAC_CH7_FIFO_DEPTH/8) 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH7_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_MULT_SIZE parameter. Maxium burst transaction size. CH7_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH7_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH7_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH7_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH7_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH7_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH7_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH7_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH7_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH7_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH7_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH7_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH7_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH7_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH7_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D0h
Read/write access: R
DMA component parameters register 5 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH6_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH6_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH6_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_MULT_SIZE parameter. Maxium burst transaction size. CH6_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH6_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH6_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH6_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH6_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH6_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH6_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH6_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH6_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH6_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH6_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH6_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH6_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH6_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH6_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_5_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D4h
Read/write access: R
DMA component parameters register 5 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH5_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH5_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH5_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_MULT_SIZE parameter. Maxium burst transaction size. CH5_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH5_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH5_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH5_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH5_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH5_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH5_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH5_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH5_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH5_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH5_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH5_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH5_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH5_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH5_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3D8h
Read/write access: R
DMA component parameters register 4 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH4_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH4_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH4_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_MULT_SIZE parameter. Maxium burst transaction size. CH4_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH4_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH4_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH4_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH4_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH4_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH4_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH4_SRC_GAT_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112.0x0 = FALSE 0x1 = TRUE |
8 |
CH4_DST_SCA_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH4_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH4_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH4_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH4_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH4_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH4_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_4_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3DCh
Read/write access: R
DMA component parameters register 4 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH3_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH3_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH3_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_MULT_SIZE parameter. Maxium burst transaction size. CH3_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH3_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH3_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH3_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH3_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH3_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH3_SRC_GAT_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH3_DST_SCA_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH3_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH3_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH3_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH3_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH3_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH3_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH3_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E0h
Read/write access: R
DMA component parameters register 3 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH2_FIFO_DEPTH |
R |
0x2 |
The value of this register is derived from the DMAC_CH2_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH2_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_MULT_SIZE parameter. Maxium burst transaction size. CH2_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH2_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH2_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH2_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH2_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH2_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH2_SRC_GAT_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH2_DST_SCA_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH2_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH2_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH2_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH2_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH2_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH2_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH2_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_3_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E4h
Read/write access: R
DMA component parameters register 3 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH1_FIFO_DEPTH |
R |
0x4 |
The value of this register is derived from the DMAC_CH1_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH1_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_MULT_SIZE parameter. Maxium burst transaction size. CH1_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH1_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH1_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH1_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH1_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH1_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH1_SRC_GAT_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_SRC_GAT_EN parameter. 0x0 = FALSE 0x1 = TRUE |
8 |
CH1_DST_SCA_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH1_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH1_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH1_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH1_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH1_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH1_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH1_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3E8h
Read/write access: R
DMA component parameters register 2 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
RSVD |
R |
- |
Reserved |
30:28 |
CH0_FIFO_DEPTH |
R |
0x5 |
The value of this register is derived from the DMAC_CH0_FIFO_DEPTH parameter. Default value is 0x0. 0x0 = 8 bytes 0x1 = 16 0x2 = 32 0x3 = 64 0x4 = 128 0x5 = Reserved 0x6 = Reserved 0x7 = Reserved |
27:19 |
RSVD |
R |
- |
Reserved |
18:16 |
CH0_MAX_MULT_SIZE |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_MULT_SIZE parameter. Maxium burst transaction size. CH0_MAX_MULT_SIZE = log2(256/DMAC_DATA_WIDTH) 0x3 = 32 bits 0x2 = 64 bits 0x1 = 128 bits |
15:14 |
CH0_FC |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_FC parameter. 0x0 = DMA 0x1 = SRC 0x2 = DST 0x3 = ANY |
13 |
CH0_HC_LLP |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_HC_LLP parameter. 0x0 = FALSE 0x1 = TRUE |
12 |
CH0_CTL_WB_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_CTL_WB_EN parameter. 0x0 = FALSE 0x1 = TRUE |
11 |
CH0_MULTI_BLK_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_MULTI_BLK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
10 |
CH0_LOCK_EN |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_LOCK_EN parameter. 0x0 = FALSE 0x1 = TRUE |
9 |
CH0_SRC_GAT_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_SRC_GAT_EN parameter. For a description of this parameter, refer to page 112. 0x0 = FALSE 0x1 = TRUE |
8 |
CH0_DST_SCA_EN |
R |
0x1 |
The value of this register is derived from the DMAC_CH0_DST_SCA_EN parameter. 0x0 = FALSE 0x1 = TRUE |
7 |
CH0_STAT_SRC |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_SRC parameter. 0x0 = FALSE 0x1 = TRUE |
6 |
CH0_STAT_DST |
R |
0x0 |
The value of this register is derived from the DMAC_CH0_STAT_DST parameter. 0x0 = FALSE 0x1 = TRUE |
5:3 |
CH0_STW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_STW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
2:0 |
CH0_DTW |
R |
0x3 |
The value of this register is derived from the DMAC_CH0_DTW parameter. 0x0 = NO_HARDCODE 0x1 = 8 0x2 = 16 0x3 = 32 0x4 = 64 0x5 = 128 0x6 = 256 0x7 = reserved |
REG_DMA_COMP_PARAMS_2_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3ECh
Read/write access: R
DMA component parameters register 2 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:28 |
CH7_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
27:24 |
CH6_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
23:20 |
CH5_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
19:16 |
CH4_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
15:12 |
CH3_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
11:8 |
CH2_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
7:4 |
CH1_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
3:0 |
CH0_MULTI_BLK_TYPE |
R |
0x0 |
The values of these bit fields are derived from the DMAC_CHx_MULTI_BLK_TYPE parameter. 0x0 = NO_HARDCODE 0x1 = CONT_RELOAD 0x2 = RELOAD_CONT 0x3 = RELOAD_RELOAD 0x4 = CONT_LLP 0x5 = RELOAD_LLP 0x6 = LLP_CONT 0x7 = LLP_RELOAD 0x8 = LLP_LLP |
REG_DMA_COMP_PARAMS_1_L
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F0h
Read/write access: R
DMA component parameters register 1 low, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:24 |
CH3_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH3_MAX_BLK_SIZE from config_form.vh CH3_MAX_BLK_SIZE = log2(DMAC_CH3_MAX_BLK_SIZE) + 1 |
23:16 |
CH2_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH2_MAX_BLK_SIZE from config_form.vh CH2_MAX_BLK_SIZE = log2(DMAC_CH2_MAX_BLK_SIZE) + 1 |
15:8 |
CH1_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH1_MAX_BLK_SIZE from config_form.vh CH1_MAX_BLK_SIZE = log2(DMAC_CH1_MAX_BLK_SIZE) + 1 |
7:0 |
CH0_MAX_BLK_SIZE |
R |
0x15 |
The value of this register is derived from the DMAC_CH0_MAX_BLK_SIZE from config_form.vh CH0_MAX_BLK_SIZE = log2(DMAC_CH0_MAX_BLK_SIZE) + 1 |
REG_DMA_COMP_PARAMS_1_H
Name: Refer to the bit table in the description for it
Size: 32
Address offset: 3F4h
Read/write access: R
DMA component parameters register 1 high, contains component identification information
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
HIGH_BIT_NUM_HS_INT3 |
R |
0x0 |
Number of hardware handshake interfaces. If it is 128, this bit read value is 1. |
30 |
HIGH_BIT_NUM_HS_INT2 |
R |
0x0 |
Number of hardware handshake interfaces. If it is greater than 63 and less than 128, this bit read value is 1. |
29 |
HIGH_BIT_NUM_HS_INT1 |
R |
0x1 |
Number of hardware handshake interfaces. If it is greater than 31 and less than 64, this bit read value is 1. |
28 |
STATIC_ENDIAN_SELECT |
R |
0 |
The value of this register is derived from the DMAC_STATIC_ENDIAN_SELECT parameter. 0 = FALSE (dynamic endian fixed) 1 = TRUE (not supported) |
27 |
ADD_ENCODED_PARAMS |
R |
1 |
The value of this register is derived from the DMAC_ADD_ENCODED_PARAMS parameter. 0 = FALSE 1 = TRUE |
26:22 |
NUM_HS_INT |
R |
0x10 |
Number of hardware handshake interfaces. The value of this register is derived from the DMAC_NUM_HS_INT parameter. NUM_HAS_INT = DMAC_NUM_HS_INT[4:0] 0x00 = 0 … 0x10 = 16 |
21:18 |
RSVD |
R |
- |
Reserved |
17:16 |
M2_DATA_WIDTH |
R |
0x0 |
AXI Master2 data width. The value of this register is derived from the DMAC_M2_DATA_WIDTH parameter. Master2 data width should be equal to that of Master 1. M2_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
15:14 |
M1_DATA_WIDTH |
R |
0x0 |
AXI Master1 data width. The value of this register is derived from the DMAC_M1_DATA_WIDTH parameter. Master1 data width should be equal to that of Master 2. M1_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = 64 bits 0x2 = 128 bits 0x3 = Reserved |
13:12 |
S_DATA_WIDTH |
R |
0x0 |
APB slave interface data width.The value of this register is derived from the DMAC_S_DATA_WIDTH parameter. The width is fixed to 32 bits for now. S_DATA_WIDTH = log2(DMAC_DATA_WIDTH/32) 0x0 = 32 bits 0x1 = Reserved 0x2 = Reserved 0x3 = Reserved |
11:10 |
NUM_MASTER_INT |
R |
0x1 |
Number of master interface. The value of this register is derived from the DMAC_NUM_MASTER_INT parameter. This value is fixed to 1 (only 2 AXI masters supported now.) 0x0 = Reserved 0x1 = 2 0x2 = Reserved 0x3 = Reserved |
9:6 |
NUM_CHANNELS |
R |
0x7 |
Number of channels. The value of this register is derived from the DMAC_NUM_CHASNNELS parameter. NUM_CHANNELS = DMAC_NUM_CHASNNELS -1 0x0 = 1 … 0xf = 16 |
5:2 |
RSVD |
R |
- |
Reserved |
1:0 |
INTR_IO |
R |
0x0 |
Interrupt output format.The value of this register is derived from the DMAC_INTR_IO parameter. 0x0 = ALL 0x1 = TYPE 0x2 = COMBINED 0x3 = reserved |
REG_DMA_COMPONENT_ID_REGS_L
Name: DMAC ID
Size: 32
Address offset: 3F8h
Read/write access: R
DMA component ID register low, identifies the DMA controller release date
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DMA_COMPONENT_ID |
R |
32'h20250311 |
DMAC ID (release_date_. Configure it in config form. |
REG_DMA_COMPONENT_ID_REGS_H
Name: It is obtained from the high 32 bits from git logs in git server.
Size: 32
Address offset: 3FCh
Read/write access: R
DMA component ID register high, identifies the DMA controller rtl version
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
RTL_GIT_VER |
R |
32'ha89a8bb5 |
It is obtained from the high 32 bits from git logs in git server. |