寄存器
请查看
寄存器访问类型
,了解 Access 列缩写的含义。
Base Address:
TIMER0_REG : 0x41017000
TIMER1_REG : 0x41017200
TIMER2_REG : 0x41017400
TIMER3_REG : 0x41017600
TIMER4_REG : 0x41017800
TIMER5_REG : 0x41017A00
TIMER6_REG : 0x41017C00
TIMER7_REG : 0x41017E00
TIMER10_REG : 0x41100400
TIMER11_REG : 0x41100600
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
Users can configure and observe the counter operation. |
|
004h |
R/W |
This register is about the update operation. |
|
008h |
R/W |
This is the interrupt enable register. |
|
00Ch |
R/W |
This register is about timer interrupt and update status. |
|
010h |
R/W |
This register is about update generation, and is user defined. |
|
014h |
R |
This is the timer count register. |
|
01Ch |
R/W |
This is the auto-reload value register. |
|
020h |
R/W |
This register is about security status. |
|
024h |
R/W |
REG_TIM_EN
Name: TIM enable register
Size: 32
Address offset: 000h
Read/write access: R/W
Users can configure and observe the counter operation.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CNT_EN |
R |
0x0 |
Counter working status
|
15:9 |
RSVD |
R |
- |
Reserved |
8 |
CNT_RUN |
R |
0x0 |
Counter run status
|
7:2 |
RSVD |
R |
- |
Reserved |
1 |
CNT_STOP |
R/W |
0x0 |
Disable the counter Poll CNT_RUN to see the counter status. If CNT_RUN is 0, it means that the counter has been disabled internally. |
0 |
CNT_START |
R/W |
0x0 |
Enable the counter Poll CNT_RUN to see the counter status. If CNT_RUN is 1, it means that the counter has been enabled internally. |
REG_TIM_CR
Name: TIM control register
Size: 32
Address offset: 004h
Read/write access: R/W
This register is about the update operation.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
ARPE |
R/W |
0x0 |
Enable auto-reload preloading
|
3 |
RSVD |
R |
- |
Reserved |
2 |
URS |
R/W |
0x0 |
Update request source
|
1 |
UDIS |
R/W |
0x0 |
Disable UEV Shadow registers keep their values. Otherwise, buffered registers are then loaded with their preload values when UEV happens. |
0 |
RSVD |
R |
- |
Reserved |
REG_TIM_DIER
Name: TIM interrupt enable register
Size: 32
Address offset: 008h
Read/write access: R/W
This is the interrupt enable register.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UIE |
R/W |
0x0 |
Enable update interrupt |
REG_TIM_SR
Name: TIM status register
Size: 32
Address offset: 00Ch
Read/write access: R/W
This register is about timer interrupt and update status.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
UG_DONE |
R |
0x1 |
UG operation status This bit is cleared by hardware when the UG bit in the TIMx_EGR register is set. When the UG operation is done, hardware set this bit to '1'. So, software can poll this bit to see the UG operation status. |
30:1 |
RSVD |
R |
- |
Reserved |
0 |
UIF |
R/W |
0x0 |
Update interrupt flag |
REG_TIM_EGR
Name: TIM event generation register
Size: 32
Address offset: 010h
Read/write access: R/W
This register is about update generation, and is user defined.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UG |
R/W |
0x0 |
Update generation Re-initialize the counter and generate an update of registers. Note that the prescaler counter is cleared too. (anyway the prescaler ratio is not affected) |
REG_TIM_CNT
Name: TIM counter register
Size: 32
Address offset: 014h
Read/write access: R
This is the timer count register.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CNT |
R |
0x0 |
Counter value |
REG_TIM_ARR
Name: TIM auto-reload register
Size: 32
Address offset: 01Ch
Read/write access: R/W
This is the auto-reload value register.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
ARR |
R/W |
0xFFFFFFFF |
The value to be loaded in the actual auto-reload register. It can be preloaded by setting ARPE bit in TIM_CR. |
REG_TIM_SEC
Name: TIM security control register
Size: 32
Address offset: 020h
Read/write access: R/W
This register is about security status.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
SEC |
R/W |
0x0 |
Secure timer enable
|
REG_TIM_BASIC_DUMMY
Name: Timer Basic Dummy Register
Size: 32
Address offset: 024h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DUMMY |
R/W |
ffffh |
Dummy register |
Base Address:
TIMER0_REG : 0x41018000
TIMER1_REG : 0x41018200
TIMER2_REG : 0x41018400
TIMER3_REG : 0x41018600
TIMER4_REG : 0x41018800
TIMER5_REG : 0x41018A00
TIMER6_REG : 0x41018C00
TIMER7_REG : 0x41018E00
TIMER10_REG : 0x41019400
TIMER11_REG : 0x41019600
TIMER12_REG : 0x41019800
TIMER13_REG : 0x41019A00
TIMER14_REG : 0x41019C00
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
User can configure and observe the counter operation. |
|
004h |
R/W |
This is the register about update operation. |
|
008h |
R/W |
||
00Ch |
R/W |
This is the register about timer interrupt and update status. |
|
010h |
R/W |
Update generation, user defined |
|
014h |
R |
||
01Ch |
R/W |
||
020h |
R/W |
This is the register about security status. |
|
024h |
R/W |
REG_TIM_EN
Name: TIM enable register
Size: 32
Address offset: 000h
Read/write access: R/W
User can configure and observe the counter operation.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CNT_EN |
R |
0x0 |
Counter working status
|
15:9 |
RSVD |
R |
- |
Reserved |
8 |
CNT_RUN |
R |
0x0 |
Counter run status
|
7:2 |
RSVD |
R |
- |
Reserved |
1 |
CNT_STOP |
R/W |
0x0 |
Disable the counter. Poll CNT_RUN to see the counter status. If CNT_RUN is 0, it means that the counter has been disabled internally. |
0 |
CNT_START |
R/W |
0x0 |
Enable the counter. Poll CNT_RUN to see the counter status. If CNT_RUN is 1, it means that the counter has been enabled internally. |
REG_TIM_CR
Name: TIM control register
Size: 32
Address offset: 004h
Read/write access: R/W
This is the register about update operation.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
ARPE |
R/W |
0x0 |
Enable auto-reload preloading
|
3 |
RSVD |
R |
- |
Reserved |
2 |
URS |
R/W |
0x0 |
Update request source
|
1 |
UDIS |
R/W |
0x0 |
Disable UEV Shadow registers keep their values. Otherwise, buffered registers are then loaded with their preload values when UEV happens. |
0 |
RSVD |
R |
- |
Reserved |
REG_TIM_DIER
Name: TIM interupt enable register
Size: 32
Address offset: 008h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UIE |
R/W |
0x0 |
Enable update interrupt |
REG_TIM_SR
Name: TIM status register
Size: 32
Address offset: 00Ch
Read/write access: R/W
This is the register about timer interrupt and update status.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
UG_DONE |
R |
0x1 |
UG operation status This bit is cleared by hardware when the UG bit in the TIMx_EGR register is set. When the UG operation is done, hardware sets this bit to '1'. So, software can poll this bit to see the UG operation status. |
30:1 |
RSVD |
R |
- |
Reserved |
0 |
UIF |
R/W |
0x0 |
Update interrupt flag |
REG_TIM_EGR
Name: TIM event generation register
Size: 32
Address offset: 010h
Read/write access: R/W
Update generation, user defined
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UG |
R/W |
0x0 |
Update generation. Re-initialize the counter and generate an update of registers. Note that the prescaler counter is cleared too. (Anyway the prescaler ratio is not affected) |
REG_TIM_CNT
Name: TIM counter register
Size: 32
Address offset: 014h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CNT |
R |
0x0 |
Counter value |
REG_TIM_ARR
Name: TIM auto-reload register
Size: 32
Address offset: 01Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
ARR |
R/W |
0xFFFFFFFF |
The value to be loaded in the actual auto-reload register. It can be preloaded by setting ARPE bit in TIM_CR. |
REG_TIM_SEC
Name: TIM security control register
Size: 32
Address offset: 020h
Read/write access: R/W
This is the register about security status.
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
SEC |
R/W |
0x0 |
Secure timer enable
|
REG_TIM_BASIC_DUMMY
Name: Timer Baisc Dummy Register
Size: 32
Address offset: 024h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DUMMY |
R/W |
ffffh |
Dummy register |
REGISTER_CONTENTS=RTL8720E
REGISTER_CONTENTS=RTL8720E
REGISTER_CONTENTS=RTL8720E
Base Address:
TIMER0_REG : 0x4200B000
TIMER1_REG : 0x4200B200
TIMER2_REG : 0x4200B400
TIMER3_REG : 0x4200B600
TIMER4_REG : 0x4200B800
TIMER5_REG : 0x4200BA00
TIMER6_REG : 0x4200BC00
TIMER7_REG : 0x4200BE00
TIMER10_REG : 0x4100A400
TIMER11_REG : 0x4100A600
TIMER12_REG : 0x4100A800
TIMER13_REG : 0x4100AA00
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
||
004h |
R/W |
||
008h |
R/W |
||
00Ch |
R/W |
||
010h |
R/W |
||
014h |
R |
||
01Ch |
R/W |
||
020h |
R/W |
REG_TIM_EN
Name: TIM enable register
Size: 32
Address offset: 000h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CNT_EN |
R |
0x0 |
Counter working status
|
15:9 |
RSVD |
R |
- |
Reserved |
8 |
CNT_RUN |
R |
0x0 |
Counter run status
|
7:2 |
RSVD |
R |
- |
Reserved |
1 |
CNT_STOP |
R/W |
0x0 |
Disable the counter. Poll cnt_run to see the counter status. If cnt_run is 0, it means that the counter has been disabled internally. |
0 |
CNT_START |
R/W |
0x0 |
Enable the counter. Poll cnt_run to see the counter status. If cnt_run is 1, it means that the counter has been enabled internally. |
REG_TIM_CR
Name: TIM control register
Size: 32
Address offset: 004h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
ARPE |
R/W |
0x0 |
Enable auto-reload preloading
|
3 |
RSVD |
R |
- |
Reserved |
2 |
URS |
R/W |
0x0 |
Update request source
|
1 |
UDIS |
R/W |
0x0 |
Disable uev. Shadow registers keep their values. Otherwise, buffered registers are then loaded with their preload values when uev happen. |
0 |
RSVD |
R |
- |
Reserved |
REG_TIM_DIER
Name: TIM interupt enable register
Size: 32
Address offset: 008h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UIE |
R/W |
0x0 |
Enable update interrupt |
REG_TIM_SR
Name: TIM status register
Size: 32
Address offset: 00Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
UG_DONE |
R |
0x1 |
Ug operation status.This bit is cleared by hardware when the ug bit in the timx_egr register is set. When the ug operation is done, hardware set this bit to '1'. So, software can poll this bit to see the ug operation status. |
30:1 |
RSVD |
R |
- |
Reserved |
0 |
UIF |
R/W |
0x0 |
Update interrupt flag |
REG_TIM_EGR
Name: TIM event generation register
Size: 32
Address offset: 010h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UG |
R/W |
0x0 |
Update generation. Re-initialize the counter and generate an update of registers. Note that the prescaler counter is cleared too.(anyway the prescaler ratio is not affected) |
REG_TIM_CNT
Name: TIM counter
Size: 32
Address offset: 014h
Read/write access: R
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CNT |
R |
0x0 |
Counter value |
REG_TIM_ARR
Name: TIM auto-reload register
Size: 32
Address offset: 01Ch
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
ARR |
R/W |
0xFFFFFFFF |
The value to be loaded in the actual auto-reload register. It can be preloaded by setting arpe bit in tim_cr. |
REG_TIM_SEC
Name: TIM security control register
Size: 32
Address offset: 020h
Read/write access: R/W
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
SEC |
R/W |
0x0 |
Secure timer enable.
|
Base Address:
TIMER0_REG : 0x40819000
TIMER1_REG : 0x40819200
TIMER2_REG : 0x40819400
TIMER3_REG : 0x40819600
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
User can configure and observe the counter operation |
|
004h |
R/W |
Registers about the update operation |
|
008h |
R/W |
Interrupt enable |
|
00Ch |
R/W |
Registers about timer interrupt and update status |
|
010h |
R/W |
Update generation user defined |
|
014h |
R |
Timer count |
|
01Ch |
R/W |
Auto-reload value |
|
020h |
R/W |
Security status |
|
024h |
R/W |
Dummy register |
REG_TIM_EN
Name: TIM enable register
Size: 32
Address offset: 000h
Read/write access: R/W
User can configure and observe the counter operation
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CNT_EN |
R |
0x0 |
Counter working status
|
15:9 |
RSVD |
R |
- |
Reserved |
8 |
CNT_RUN |
R |
0x0 |
Counter run status
|
7:2 |
RSVD |
R |
- |
Reserved |
1 |
CNT_STOP |
R/W |
0x0 |
Disable the counter. Poll CNT_RUN to see the counter status. If CNT_RUN is 0, it means that the counter has been disabled internally. |
0 |
CNT_START |
R/W |
0x0 |
Enable the counter. Poll CNT_RUN to see the counter status. If CNT_RUN is 1, it means that the counter has been enabled internally. |
REG_TIM_CR
Name: TIM control register
Size: 32
Address offset: 004h
Read/write access: R/W
Registers about the update operation
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
ARPE |
R/W |
0x0 |
Enable auto-reload preloading
|
3 |
RSVD |
R |
- |
Reserved |
2 |
URS |
R/W |
0x0 |
Update request source
|
1 |
UDIS |
R/W |
0x0 |
Disable UEV. Shadow registers keep their values. Otherwise, buffered registers are then loaded with their preload values when UEV happen. |
0 |
RSVD |
R |
- |
Reserved |
REG_TIM_DIER
Name: TIM interupt enable register
Size: 32
Address offset: 008h
Read/write access: R/W
Interrupt enable
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UIE |
R/W |
0x0 |
Enable update interrupt |
REG_TIM_SR
Name: TIM status register
Size: 32
Address offset: 00Ch
Read/write access: R/W
Registers about timer interrupt and update status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
UG_DONE |
R |
0x1 |
UG operation status This bit is cleared by hardware when the UG bit in the TIMx_EGR register is set. When the UG operation is done, hardware set this bit to '1'. So, software can poll this bit to see the UG operation status. |
30:1 |
RSVD |
R |
- |
Reserved |
0 |
UIF |
R/W |
0x0 |
Update interrupt flag |
REG_TIM_EGR
Name: TIM event generation register
Size: 32
Address offset: 010h
Read/write access: R/W
Update generation user defined
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UG |
R/W |
0x0 |
Update generation. Re-initialize the counter and generate an update of registers. Note that the prescaler counter is cleared too.(anyway the prescaler ratio is not affected) |
REG_TIM_CNT
Name: TIM counter
Size: 32
Address offset: 014h
Read/write access: R
Timer count
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CNT |
R |
0x0 |
Counter value |
REG_TIM_ARR
Name: TIM auto-reload register
Size: 32
Address offset: 01Ch
Read/write access: R/W
Auto-reload value
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
ARR |
R/W |
0xFFFFFFFF |
The value to be loaded in the actual auto-reload register. It can be preloaded by setting ARPE bit in TIM_CR. |
REG_TIM_SEC
Name: TIM security control register
Size: 32
Address offset: 020h
Read/write access: R/W
Security status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
SEC |
R/W |
0x0 |
Secure timer enable.
|
REG_TIM_BASIC_DUMMY
Name: Timer Baisc Dummy Register
Size: 32
Address offset: 024h
Read/write access: R/W
Dummy register
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
DUMMY |
R/W |
ffffh |
Dummy register |
Base Address:
TIMER0_REG : 0x40808000
TIMER1_REG : 0x40808200
TIMER2_REG : 0x40808400
TIMER3_REG : 0x40808600
Name |
Address offset |
Access |
Description |
|---|---|---|---|
000h |
R/W |
User can configure and observe the counter operation |
|
004h |
R/W |
Registers about the update operation |
|
008h |
R/W |
Interrupt enable |
|
00Ch |
R/W |
Registers about timer interrupt and update status |
|
010h |
R/W |
Update generation user defined |
|
014h |
R |
Timer count |
|
01Ch |
R/W |
Auto-reload value |
|
020h |
R/W |
Security status |
|
024h |
R/W |
Dummy register |
REG_TIM_EN
Name: TIM enable register
Size: 32
Address offset: 000h
Read/write access: R/W
User can configure and observe the counter operation
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:17 |
RSVD |
R |
- |
Reserved |
16 |
CNT_EN |
R |
0x0 |
Counter working status
|
15:9 |
RSVD |
R |
- |
Reserved |
8 |
CNT_RUN |
R |
0x0 |
Counter run status
|
7:2 |
RSVD |
R |
- |
Reserved |
1 |
CNT_STOP |
R/W |
0x0 |
Disable the counter. Poll CNT_RUN to see the counter status. If CNT_RUN is 0, it means that the counter has been disabled internally. |
0 |
CNT_START |
R/W |
0x0 |
Enable the counter. Poll CNT_RUN to see the counter status. If CNT_RUN is 1, it means that the counter has been enabled internally. |
REG_TIM_CR
Name: TIM control register
Size: 32
Address offset: 004h
Read/write access: R/W
Registers about the update operation
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:5 |
RSVD |
R |
- |
Reserved |
4 |
ARPE |
R/W |
0x0 |
Enable auto-reload preloading
|
3 |
RSVD |
R |
- |
Reserved |
2 |
URS |
R/W |
0x0 |
Update request source
|
1 |
UDIS |
R/W |
0x0 |
Disable UEV. Shadow registers keep their values. Otherwise, buffered registers are then loaded with their preload values when UEV happen. |
0 |
RSVD |
R |
- |
Reserved |
REG_TIM_DIER
Name: TIM interupt enable register
Size: 32
Address offset: 008h
Read/write access: R/W
Interrupt enable
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UIE |
R/W |
0x0 |
Enable update interrupt |
REG_TIM_SR
Name: TIM status register
Size: 32
Address offset: 00Ch
Read/write access: R/W
Registers about timer interrupt and update status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31 |
UG_DONE |
R |
0x1 |
UG operation status This bit is cleared by hardware when the UG bit in the TIMx_EGR register is set. When the UG operation is done, hardware set this bit to '1'. So, software can poll this bit to see the UG operation status. |
30:1 |
RSVD |
R |
- |
Reserved |
0 |
UIF |
R/W |
0x0 |
Update interrupt flag |
REG_TIM_EGR
Name: TIM event generation register
Size: 32
Address offset: 010h
Read/write access: R/W
Update generation user defined
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
UG |
R/W |
0x0 |
Update generation. Re-initialize the counter and generate an update of registers. Note that the prescaler counter is cleared too.(anyway the prescaler ratio is not affected) |
REG_TIM_CNT
Name: TIM counter
Size: 32
Address offset: 014h
Read/write access: R
Timer count
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
CNT |
R |
0x0 |
Counter value |
REG_TIM_ARR
Name: TIM auto-reload register
Size: 32
Address offset: 01Ch
Read/write access: R/W
Auto-reload value
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:0 |
ARR |
R/W |
0xFFFFFFFF |
The value to be loaded in the actual auto-reload register. It can be preloaded by setting ARPE bit in TIM_CR. |
REG_TIM_SEC
Name: TIM security control register
Size: 32
Address offset: 020h
Read/write access: R/W
Security status
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:1 |
RSVD |
R |
- |
Reserved |
0 |
SEC |
R/W |
0x0 |
Secure timer enable.
|
REG_TIM_BASIC_DUMMY
Name: Timer Baisc Dummy Register
Size: 32
Address offset: 024h
Read/write access: R/W
Dummy register
Bit |
Symbol |
Access |
INI |
Description |
|---|---|---|---|---|
31:8 |
RSVD |
R |
- |
Reserved |
7:0 |
DUMMY |
R/W |
8'hf0 |
Dummy register |